[Federal Register Volume 90, Number 130 (Thursday, July 10, 2025)]
[Rules and Regulations]
[Pages 30577-30580]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2025-12858]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2025-1352; Project Identifier MCAI-2025-00812-T;
Amendment 39-23078; AD 2025-13-12]
RIN 2120-AA64
Airworthiness Directives; Airbus SAS Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule; request for comments.
-----------------------------------------------------------------------
[[Page 30578]]
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all
Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by
a report of loss of control of an outboard aileron surface due to
hydraulic fluid contaminating an electronic card of the flight control
remote module (FCRM). This AD requires replacing any affected elevator
FCRM and prohibits installing aileron or spoiler FCRMs in place of
elevator or rudder FCRMs. This AD also limits the installation of FCRMs
under certain conditions. The FAA is issuing this AD to address the
unsafe condition on these products.
DATES: This AD is effective July 25, 2025.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of July 25,
2025.
The FAA must receive comments on this AD by August 25, 2025.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to regulations.gov. Follow
the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
AD Docket: You may examine the AD docket at regulations.gov under
Docket No. FAA-2025-1352; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this final rule, the mandatory continuing airworthiness
information (MCAI), any comments received, and other information. The
street address for Docket Operations is listed above.
Material Incorporated by Reference:
For European Union Aviation Safety Agency (EASA) material
identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668
Cologne, Germany; telephone +49 221 8999 000; email [email protected].
You may find this material on the EASA website at ad.easa.europa.eu.
You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th St., Des
Moines, WA. For information on the availability of this material at the
FAA, call 206-231-3195. It is also available at regulations.gov under
Docket No. FAA-2025-1352.
FOR FURTHER INFORMATION CONTACT: Udara Dharmasena, Aviation Safety
Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 562-
627-5295; email: [email protected].
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written data, views, or arguments
about this final rule. Send your comments using a method listed under
the ADDRESSES section. Include ``Docket No. FAA-2025-1352; Project
Identifier MCAI-2025-00812-T'' at the beginning of your comments. The
most helpful comments reference a specific portion of the final rule,
explain the reason for any recommended change, and include supporting
data. The FAA will consider all comments received by the closing date
and may amend this final rule because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
regulations.gov, including any personal information you provide. The
agency will also post a report summarizing each substantive verbal
contact received about this final rule.
Confidential Business Information
CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this AD contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this AD, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this AD. Submissions containing CBI should be sent to Udara
Dharmasena, Aviation Safety Engineer, FAA, 2200 South 216th St., Des
Moines, WA 98198; phone: 562-627-5295; email:
[email protected]. Any commentary that the FAA receives which
is not specifically designated as CBI will be placed in the public
docket for this rulemaking.
Background
EASA, which is the Technical Agent for the Member States of the
European Union, has issued EASA AD 2025-0129, dated June 5, 2025 (EASA
AD 2025-0129) (also referred to as ``the MCAI''), to correct an unsafe
condition for all Model A350-941 and -1041 airplanes. The MCAI states
that an occurrence was reported of loss of control of an outboard
aileron surface. Subsequent investigations determined that the
electronic card of the FCRM of that aileron had been contaminated by
hydraulic fluid. In addition, EASA determined that certain
servocontrols were exposed to hydraulic contamination before delivery
of the airplane to its first operator. Due to the similarity of design,
elevator and rudder FCRMs could be subject to the same failure mode.
This condition, if not detected and corrected, could lead to runaway of
rudder or elevator surface, resulting in loss of control of the
airplane.
The FAA is issuing this AD to address the unsafe condition on these
products.
You may examine the MCAI in the AD docket at regulations.gov under
Docket No. FAA-2025-1352.
Material Incorporated by Reference Under 1 CFR Part 51
The FAA reviewed EASA AD 2025-0129, which specifies procedures for
replacing affected FCRMs, which have been exposed to hydraulic fuel
contamination, with serviceable FCRMs and repairing any related
hydraulic leaks on the airplane. EASA AD 2025-0129 prohibits
``swapping'' elevator or rudder FCRMs with spoiler or aileron FCRMs.
EASA AD 2025-0129 also prohibits installing an FCRM unless it is a
serviceable FCRM.
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in the ADDRESSES section.
FAA's Determination
These products have been approved by the civil aviation authority
of another country and are approved for operation in the United States.
Pursuant to the FAA's bilateral agreement with this State of Design
Authority, that authority has notified the FAA of the unsafe condition
described in the MCAI referenced above. The FAA is issuing this AD
after determining that the unsafe condition described previously is
likely to exist or develop on other products of the same type design.
Requirements of This AD
This AD requires accomplishing the actions specified in EASA AD
2025-0129 described previously, except for
[[Page 30579]]
any differences identified as exceptions in the regulatory text of this
AD.
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA developed a process to use some civil aviation
authority (CAA) ADs as the primary source of information for compliance
with requirements for corresponding FAA ADs. The FAA has been
coordinating this process with manufacturers and CAAs. As a result,
EASA AD 2025-0129 is incorporated by reference in this AD. This AD
requires compliance with EASA AD 2025-0129 in its entirety through that
incorporation, except for any differences identified as exceptions in
the regulatory text of this AD. Using common terms that are the same as
the heading of a particular section in EASA AD 2025-0129 does not mean
that operators need comply only with that section. For example, where
the AD requirement refers to ``all required actions and compliance
times,'' compliance with this AD requirement is not limited to the
section titled ``Required Action(s) and Compliance Time(s)'' in EASA AD
2025-0129. Material required by EASA AD 2025-0129 for compliance will
be available at regulations.gov under Docket No. FAA-2025-1352 after
this AD is published.
Interim Action
The FAA considers that this AD is an interim action.
Justification for Immediate Adoption and Determination of the Effective
Date
Section 553(b) of the Administrative Procedure Act (APA) (5 U.S.C.
551 et seq.) authorizes agencies to dispense with notice and comment
procedures for rules when the agency, for ``good cause,'' finds that
those procedures are ``impracticable, unnecessary, or contrary to the
public interest.'' Under this section, an agency, upon finding good
cause, may issue a final rule without providing notice and seeking
comment prior to issuance. Further, section 553(d) of the APA
authorizes agencies to make rules effective in less than thirty days,
upon a finding of good cause.
An unsafe condition exists that requires the immediate adoption of
this AD without providing an opportunity for public comments prior to
adoption. The FAA has found that the risk to the flying public
justifies forgoing notice and comment prior to adoption of this rule
because FCRM electronic cards exposed to hydraulic fluid have led to
loss of control of an outboard aileron surface and elevator FCRM
electronic cards exposed to hydraulic fluid are also subject failure,
due to their similarity of design. Control of the airplane is
significantly degraded through the loss of control of an elevator or
rudder surface, resulting in loss of control of the airplane.
Additionally, some of the corrective actions in this AD must be
accomplished before further flight, while the remaining actions must be
done within 18 or 24 days, depending on the type of FCRM. The
compliance times are shorter than the time necessary for the public to
comment and for publication of the final rule. Accordingly, notice and
opportunity for prior public comment are impracticable and contrary to
the public interest pursuant to 5 U.S.C. 553(b).
In addition, the FAA finds that good cause exists pursuant to 5
U.S.C. 553(d) for making this amendment effective in less than 30 days,
for the same reasons the FAA found good cause to forgo notice and
comment.
Regulatory Flexibility Act (RFA)
The requirements of the RFA do not apply when an agency finds good
cause pursuant to 5 U.S.C. 553 to adopt a rule without prior notice and
comment. Because the FAA has determined that it has good cause to adopt
this rule without notice and comment, RFA analysis is not required.
Costs of Compliance
The FAA estimates that this AD affects 37 airplanes of U.S.
registry. The FAA estimates the following costs to comply with this AD:
Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
Cost on U.S.
Action Labor cost Parts cost Cost per product operators
----------------------------------------------------------------------------------------------------------------
Replacement.............. Up to 12 work-hours $110,256 (if all Up to $111,276...... Up to $4,117,212.
x $85 per hour = four FCMSs are
$1,020. replaced).
----------------------------------------------------------------------------------------------------------------
The FAA estimates the following costs to do any necessary on-
condition repairs of any related hydraulic leaks on the airplane. The
FAA has no way of determining the number of airplanes that might need
this on-condition action:
Estimated Costs for On-Condition Repairs
------------------------------------------------------------------------
Labor cost Parts cost Cost per product
------------------------------------------------------------------------
3 work-hours x $85 per hour = Up to $27,564..... Up to $27,819.
$255.
------------------------------------------------------------------------
According to the manufacturer, some or all of the costs of this AD
may be covered under warranty, thereby reducing the cost impact on
affected operators. The FAA does not control warranty coverage for
affected operators. As a result, the FAA has included all known costs
in the cost estimate.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or
[[Page 30580]]
develop on products identified in this rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866, and
(2) Will not affect intrastate aviation in Alaska.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
2025-13-12 Airbus SAS: Amendment 39-23078; Docket No. FAA-2025-1352;
Project Identifier MCAI-2025-00812-T.
(a) Effective Date
This airworthiness directive (AD) is effective July 25, 2025.
(b) Affected ADs
None.
(c) Applicability
This AD applies to all Airbus SAS Model A350-941 and -1041
airplanes, certificated in any category.
(d) Subject
Air Transport Association (ATA) of America Code 27, Flight
Controls.
(e) Unsafe Condition
This AD was prompted by a report of loss of control of an
outboard aileron surface due to hydraulic fluid contaminating an
electronic card of the flight control remote module (FCRM). The FAA
is issuing this AD to address FCRM electronic cards exposed to
hydraulic fluid contamination. This condition, if not detected and
corrected, could lead to runaway of rudder or elevator surface,
resulting in loss of control of the airplane.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
Except as specified in paragraphs (h) and (i) of this AD: Comply
with all required actions and compliance times specified in, and in
accordance with, European Union Aviation Safety Agency (EASA) AD
2025-0129, dated June 5, 2025 (EASA AD 2025-0129).
(h) Exceptions to EASA AD 2025-0129
(1) Where EASA AD 2025-0129 refers to ``07 May 2025 [the
effective date of EASA AD 2025-0099]'', this AD requires using the
effective date of this AD.
(2) Where EASA AD 2025-0129 refers to its effective date, this
AD requires using the effective date of this AD.
(3) Where paragraph (1) of EASA AD 2025-0129 states ``do not
swap'', for this AD replace that text with ``do not replace''.
(4) Where paragraph (2) of EASA AD 2025-0129 states ``is
reported on an aeroplane'', for this AD replace that text with ``is
documented in the aircraft maintenance records or has been reported
to Airbus''.
(5) Where Table 1 of EASA AD 2025-0129 states ``close to'', for
this AD replace that text with ``adjacent to''.
(6) This AD does not adopt the ``Remarks'' section of EASA AD
2025-0129.
(i) No Reporting Requirement
Although the material referenced in EASA AD 2025-0129 specifies
to submit certain information to the manufacturer, this AD does not
include that requirement.
(j) Additional AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, AIR-
520, Continued Operational Safety Branch, FAA, has the authority to
approve AMOCs for this AD, if requested using the procedures found
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request
to your principal inspector responsible Flight Standards Office, as
appropriate. If sending information directly to the manager of the
Continued Operational Safety Branch, send it to the attention of the
person identified in paragraph (k)(1) of this AD and email to:
[email protected]. Before using any approved AMOC, notify your
appropriate principal inspector, or lacking a principal inspector,
the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain instructions from a manufacturer, the instructions must be
accomplished using a method approved by the Manager, AIR-520,
Continued Operational Safety Branch, FAA.; or EASA; or Airbus SAS's
EASA Design Organization Approval (DOA). If approved by the DOA, the
approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by
paragraph (j)(2) of this AD, if any material referenced in EASA AD
2025-0129 that contains paragraphs that are labeled as RC, the
instructions in RC paragraphs, including subparagraphs under an RC
paragraph, must be done to comply with this AD; any paragraphs,
including subparagraphs under those paragraphs, that are not
identified as RC are recommended. The instructions in paragraphs,
including subparagraphs under those paragraphs, not identified as RC
may be deviated from using accepted methods in accordance with the
operator's maintenance or inspection program without obtaining
approval of an AMOC, provided the instructions identified as RC can
be done and the airplane can be put back in an airworthy condition.
Any substitutions or changes to instructions identified as RC
require approval of an AMOC.
(k) Additional Information
(1) For more information about this AD, contact Udara
Dharmasena, Aviation Safety Engineer, FAA, 2200 South 216th St., Des
Moines, WA 98198; phone: 562-627-5295; email:
[email protected].
(2) For Airbus material identified in this AD that is not
incorporated by reference, contact Airbus SAS, Airworthiness
Office--EAL, Rond-Point Emile Dewoitine No: 2, 31700 Blagnac Cedex,
France; telephone +33 5 61 93 36 96; fax +33 5 61 93 45 80; email
airbus.com">continued-airworthiness.a350@airbus.com; website airbus.com.
(l) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference of the material listed in this paragraph
under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this material as applicable to do the actions
required by this AD, unless this AD specifies otherwise.
(i) European Union Aviation Safety Agency (EASA) AD 2025-0129,
dated June 5, 2025.
(ii) [Reserved]
(3) For EASA material identified in this AD, contact EASA,
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221
8999 000; email [email protected]. You may find this material on
the EASA website at ad.easa.europa.eu.
(4) You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th St.,
Des Moines, WA. For information on the availability of this material
at the FAA, call 206-231-3195.
(5) You may view this material at the National Archives and
Records Administration (NARA). For information on the availability
of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected].
Issued on June 30, 2025.
Peter A. White,
Deputy Director, Integrated Certificate Management Division, Aircraft
Certification Service.
[FR Doc. 2025-12858 Filed 7-8-25; 4:15 pm]
BILLING CODE 4910-13-P