[Federal Register Volume 90, Number 81 (Tuesday, April 29, 2025)]
[Proposed Rules]
[Pages 17743-17746]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2025-07269]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2025-0742; Project Identifier MCAI-2024-00682-T]
RIN 2120-AA64
Airworthiness Directives; Airbus SAS Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to supersede Airworthiness Directive (AD)
2020-02-14, which applies to certain Airbus SAS Model A350-941 and -
1041 airplanes. AD 2020-02-14 requires a one-time inspection of the
oxygen containers and adjacent panels and applicable corrective
actions. Since the FAA issued AD 2020-02-14, it was determined that
additional airplanes may be affected by the same unsafe condition. This
proposed AD would continue to require the actions in AD 2020-02-14 and
would require expanding the applicability to include additional
airplanes, as specified in a European Union Aviation Safety Agency
(EASA) AD, which is proposed for incorporation by reference (IBR). The
FAA is proposing this AD to address the unsafe condition on these
products.
DATES: The FAA must receive comments on this proposed AD by June 13,
2025.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to regulations.gov. Follow
the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
AD Docket: You may examine the AD docket at regulations.gov under
Docket No. FAA-2025-0742; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this NPRM, the mandatory continuing airworthiness
information (MCAI), any comments received, and other information. The
street address for Docket Operations is listed above.
[[Page 17744]]
Material Incorporated by Reference:
For Airbus material identified in this AD, contact Airbus
SAS, Airworthiness Office--EAL, Rond-Point Emile Dewoitine No: 2, 31700
Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 45
80; email airbus.com">continued-airworthiness.a350@airbus.com; website airbus.com.
For EASA material identified in this proposed AD, contact
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221
8999 000; email [email protected]. You may find this material on the
EASA website at ad.easa.europa.eu. It is also available at
regulations.gov under Docket No. FAA-2025-0742.
You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th St., Des
Moines, WA. For information on the availability of this material at the
FAA, call 206-231-3195.
FOR FURTHER INFORMATION CONTACT: Nicole Tsang, Aviation Safety
Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 206-
231-3959; email: [email protected].
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under the ADDRESSES section. Include ``Docket No. FAA-2025-0742;
Project Identifier MCAI-2024-00682-T'' at the beginning of your
comments. The most helpful comments reference a specific portion of the
proposal, explain the reason for any recommended change, and include
supporting data. The FAA will consider all comments received by the
closing date and may amend this proposal because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
regulations.gov, including any personal information you provide. The
agency will also post a report summarizing each substantive verbal
contact received about this NPRM.
Confidential Business Information
CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this NPRM contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this NPRM, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this NPRM. Submissions containing CBI should be sent to
Nicole Tsang, Aviation Safety Engineer, FAA, 2200 South 216th St., Des
Moines, WA 98198; phone: 206-231-3959; email: [email protected].
Any commentary that the FAA receives which is not specifically
designated as CBI will be placed in the public docket for this
rulemaking.
Background
The FAA issued AD 2020-02-14, Amendment 39-19828 (85 FR 6757,
February 6, 2020) (AD 2020-02-14), for certain Airbus SAS Model A350-
941 and -1041 airplanes. AD 2020-02-14 was prompted by an MCAI
originated by EASA, which is the Technical Agent for the Member States
of the European Union. EASA issued AD 2019-0210, dated August 26, 2019
(EASA AD 2019-0210), to correct an unsafe condition.
AD 2020-02-14 requires a one-time inspection of the oxygen
containers and adjacent panels, and applicable corrective actions. The
FAA issued AD 2020-02-14 to address damaged and unlocked fasteners of
the oxygen containers and adjacent panels in the passenger supply
channels (PSCs), which could result in insufficient clearance between
the oxygen container and adjacent panels and prevent the opening of the
oxygen containers, and consequent failure of the oxygen masks to deploy
and provide supplemental oxygen in case of an in-flight decompression,
possibly resulting in injury to cabin occupants.
Actions Since AD 2020-02-14 Was Issued
Since the FAA issued AD 2020-02-14, EASA superseded EASA AD 2019-
0210 and issued EASA AD 2024-0220, dated November 20, 2024 (EASA AD
2024-0220) (also referred to as the MCAI), to correct an unsafe
condition for certain Airbus SAS Model A350-941 and -1041 airplanes.
The MCAI states that since EASA AD 2019-0210 was issued, it was
determined that additional A350 manufacturer serial numbers (airplanes)
may be affected by the same unsafe condition.
The FAA is proposing this AD to address the unsafe condition on
these products. You may examine the MCAI in the AD docket at
regulations.gov under Docket No. FAA-2025-0742.
Explanation of Retained Requirements
Although this proposed AD does not explicitly restate the
requirements of AD 2020-02-14, this proposed AD would retain all of the
requirements of AD 2020-02-14. Those requirements are referenced in
EASA AD 2024-0220, which, in turn, is referenced in paragraph (g) of
this proposed AD.
Material Incorporated by Reference Under 1 CFR Part 51
EASA AD 2024-0220 specifies procedures for inspecting the oxygen
containers and the installation of adjacent panels located in all PSCs,
to check that each fastener of each panel/component is locked and to
measure the clearance between the oxygen container door lid and the
adjacent panel/component. EASA AD 2024-0220 also describes procedures
for applicable corrective actions, including attaining minimum
clearance, locking any unlocked fasteners, and replacing damaged parts.
The FAA reviewed Airbus Alert Operators Transmission (AOT) A35P015-
19, Revision 01, dated June 19, 2019. This material identifies affected
airplanes for the Group 1 airplanes specified in EASA AD 2024-0220.
The FAA also reviewed Airbus AOT A35P023-24, Revision 01, dated
July 25, 2024. This material identifies affected airplanes for the
Group 2 airplanes specified in EASA AD 2024-0220.
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in the ADDRESSES section.
FAA's Determination
This product has been approved by the aviation authority of another
country and is approved for operation in the United States. Pursuant to
the FAA's bilateral agreement with this State of Design Authority, it
has notified the FAA of the unsafe condition described in the MCAI
referenced above. The FAA is issuing this NPRM after determining that
the unsafe condition described previously is likely to exist or develop
in other products of the same type design.
Proposed AD Requirements in This NPRM
This proposed AD would require accomplishing the actions specified
in EASA AD 2024-0220 described previously, except for any differences
[[Page 17745]]
identified as exceptions in the regulatory text of this proposed AD.
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA developed a process to use some civil aviation
authority (CAA) ADs as the primary source of information for compliance
with requirements for corresponding FAA ADs. The FAA has been
coordinating this process with manufacturers and CAAs. As a result, the
FAA proposes to incorporate EASA AD 2024-0220 by reference in the FAA
final rule. This proposed AD would, therefore, require compliance with
EASA AD 2024-0220 in its entirety through that incorporation, except
for any differences identified as exceptions in the regulatory text of
this proposed AD. Using common terms that are the same as the heading
of a particular section in EASA AD 2024-0220 does not mean that
operators need comply only with that section. For example, where the AD
requirement refers to ``all required actions and compliance times,''
compliance with this AD requirement is not limited to the section
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2024-
0220. Material required by EASA AD 2024-0220 for compliance will be
available at regulations.gov under Docket No. FAA-2025-0742 after the
FAA final rule is published.
Costs of Compliance
The FAA estimates that this AD, if adopted as proposed, would
affect 19 airplanes of U.S. registry. The FAA estimates the following
costs to comply with this proposed AD:
Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
Cost per
Action Labor cost Parts cost product Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Retained actions from AD 2020- 4 work-hours x $85 $0 $340 $5,440 (16 airplanes).
02-14. per hour = $340.
New proposed actions........... 4 work-hours x $85 0 340 1,020 (3 airplanes).
per hour = $340.
----------------------------------------------------------------------------------------------------------------
Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
Cost per
Labor cost Parts cost product
------------------------------------------------------------------------
1 work-hour x $85 per hour = $85........ * $0 $85
------------------------------------------------------------------------
* The FAA has received no definitive data on the parts costs for the on-
condition actions.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Would not affect intrastate aviation in Alaska, and
(3) Would not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by:
0
a. Removing Airworthiness Directive (AD) 2020-02-14, Amendment 39-19828
(85 FR 6757, February 6, 2020); and
0
b. Adding the following new AD:
Airbus SAS: Docket No. FAA-2025-0742; Project Identifier MCAI-2024-
00682-T.
(a) Comments Due Date
The FAA must receive comments on this airworthiness directive
(AD) by June 13, 2025.
(b) Affected ADs
This AD replaces AD 2020-02-14, Amendment 39-19828 (85 FR 6757,
February 6, 2020) (AD 2020-02-14).
(c) Applicability
This AD applies to Airbus SAS Model A350-941 and -1041
airplanes, certificated in any category, having manufacturer serial
numbers listed in Airbus Alert Operators Transmission (AOT) A35P015-
19, Revision 01, dated June 19, 2019; and Airbus AOT A35P023-24,
Revision 01, dated July 25, 2024.
(d) Subject
Air Transport Association (ATA) of America Code 35, Oxygen.
(e) Unsafe Condition
This AD was prompted by a report that during inspection of the
installation of oxygen containers, certain fasteners of the oxygen
containers and adjacent panels in the passenger supply channels
(PSCs) were found damaged or unlocked; which could result in
insufficient clearance between the oxygen container and adjacent
panels. This
[[Page 17746]]
AD was also prompted by a determination that additional airplanes
may be affected by the same unsafe condition. The FAA is issuing
this AD to address damaged and unlocked fasteners of the oxygen
containers and adjacent panels in the PSCs, which could result in
insufficient clearance between the oxygen container and adjacent
panels. The unsafe condition, if not addressed, could prevent the
opening of the oxygen containers and result in failure of oxygen
masks to deploy and provide supplemental oxygen supply in case of an
in-flight decompression, possibly resulting in injury to cabin
occupants.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
Except as specified in paragraphs (h) and (i) of this AD: Comply
with all required actions and compliance times specified in, and in
accordance with, European Union Aviation Safety Agency (EASA) AD
2024-0220, dated November 20, 2024 (EASA AD 2024-0220).
(h) Exceptions to EASA AD 2024-0220
(1) Where EASA AD 2024-0220 refers to ``September 9, 2019 [the
effective date of EASA AD 2019-0210],'' this AD requires using March
12, 2020 (the effective date of AD 2020-02-14).
(2) Where EASA AD 2024-0220 refers to its effective date, this
AD requires using the effective date of this AD.
(3) Where the ``Groups'' definition in EASA AD 2024-0220
specifies ``Group 1 aeroplanes are those having an MSN as listed in
the AOT1'' this AD requires replacing that text with ``Group 1
airplanes are those having an MSN as listed in Airbus AOT A35P015-
19, Revision 01, dated June 19, 2019.''
(4) Where the ``Groups'' definition in EASA AD 2024-0220
specifies ``Group 2 aeroplanes are those having an MSN as listed in
the AOT2'' this AD requires replacing that text with ``Group 2
airplanes are those having an MSN as listed in Airbus AOT A35P023-
24, Revision 01, dated July 25, 2024.''
(5) This AD does not adopt the ``Remarks'' section of EASA AD
2024-0220.
(i) No Reporting Requirement
Although the material referenced in EASA AD 2024-0220 specifies
to submit certain information to the manufacturer, this AD does not
include that requirement.
(j) Additional AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager AIR-
520, Continued Operational Safety Branch, FAA, has the authority to
approve AMOCs for this AD, if requested using the procedures found
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request
to your principal inspector or responsible Flight Standards Office,
as appropriate. If sending information directly to the manager of
AIR-520, Continued Operational Safety Branch, send it to the
attention of the person identified in paragraph (k) of this AD and
email to: [email protected]. Before using any approved AMOC, notify your
appropriate principal inspector, or lacking a principal inspector,
the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain instructions from a manufacturer, the instructions must be
accomplished using a method approved by the Manager, AIR-520,
Continued Operational Safety Branch, FAA; or EASA; or Airbus SAS's
EASA Design Organization Approval (DOA). If approved by the DOA, the
approval must include the DOA-authorized signature.
(k) Additional Information
For more information about this AD, contact Nicole Tsang,
Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA
98198; phone: 206-231-3959; email: [email protected].
(l) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference of the material listed in this paragraph
under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this material as applicable to do the actions
required by this AD, unless this AD specifies otherwise.
(i) Airbus Alert Operators Transmission (AOT) A35P015-19,
Revision 01, dated June 19, 2019.
(ii) Airbus AOT A35P023-24, Revision 01, dated July 25, 2024.
(iii) European Union Aviation Safety Agency (EASA) AD 2024-0220,
dated November 20, 2024.
(3) For Airbus material identified in this AD, contact Airbus
SAS, Airworthiness Office--EAL, Rond-Point Emile Dewoitine No: 2,
31700 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5
61 93 45 80; email airbus.com">continued-airworthiness.a350@airbus.com; website
airbus.com.
(4) For EASA material identified in this AD, contact EASA,
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221
8999 000; email [email protected]. You may find this material on
the EASA website at ad.easa.europa.eu.
(5) You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th St.,
Des Moines, WA. For information on the availability of this material
at the FAA, call 206-231-3195.
(6) You may view this material at the National Archives and
Records Administration (NARA). For information on the availability
of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected].
Issued on April 22, 2025.
Peter A. White,
Deputy Director, Integrated Certificate Management Division, Aircraft
Certification Service.
[FR Doc. 2025-07269 Filed 4-28-25; 8:45 am]
BILLING CODE 4910-13-P