[Federal Register Volume 90, Number 63 (Thursday, April 3, 2025)]
[Rules and Regulations]
[Pages 14567-14569]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2025-05708]
========================================================================
Rules and Regulations
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains regulatory documents
having general applicability and legal effect, most of which are keyed
to and codified in the Code of Federal Regulations, which is published
under 50 titles pursuant to 44 U.S.C. 1510.
The Code of Federal Regulations is sold by the Superintendent of Documents.
========================================================================
Federal Register / Vol. 90, No. 63 / Thursday, April 3, 2025 / Rules
and Regulations
[[Page 14567]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2024-2542; Project Identifier MCAI-2023-00611-R;
Amendment 39-22984; AD 2025-05-12]
RIN 2120-AA64
Airworthiness Directives; Airbus Helicopters (Type Certificate
Previously Held by Eurocopter France)
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is superseding Airworthiness Directive (AD) 2008-10-01
and AD 2010-05-51, which applied to certain Eurocopter France (now
Airbus Helicopters) Model EC120B helicopters. AD 2008-10-01 required
replacing certain part-numbered and serial-numbered spherical thrust
bearings. AD 2010-05-51 required repetitively inspecting the main rotor
(M/R) head rotor hub (rotor hub) and, depending on the results, taking
corrective action. Since the FAA issued those ADs, the manufacturer
revised the airworthiness limitations section (ALS) to incorporate
various airworthiness limitations, tasks, and associated thresholds and
intervals that were previously contained in service bulletins, as well
as incorporate a new task. This AD requires revising the ALS of the
existing maintenance manual (MM) or instructions for continued
airworthiness (ICAs) and the existing approved maintenance or
inspection program, as applicable, as specified in a European Union
Aviation Safety Agency (EASA) AD, which is incorporated by reference.
The FAA is issuing this AD to address the unsafe condition on these
products.
DATES: This AD is effective May 8, 2025.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of May 8, 2025.
ADDRESSES:
AD Docket: You may examine the AD docket at regulations.gov under
Docket No. FAA-2024-2542; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this final rule, the mandatory continuing airworthiness
information (MCAI), any comments received, and other information. The
address for Docket Operations is U.S. Department of Transportation,
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200
New Jersey Avenue SE, Washington, DC 20590.
Material Incorporated by Reference:
For EASA material identified in this AD, contact EASA,
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; phone: +49 221 8999
000; email: [email protected]; website: easa.europa.eu. You may find
the EASA material on the EASA website at ad.easa.europa.eu.
You may view this material at the FAA, Office of the
Regional Counsel, Southwest Region, FAA, 10101 Hillwood Parkway, Room
6N-321, Fort Worth, TX 76177. For information on the availability of
this material at the FAA, call (817) 222-5110. It is also available at
regulations.gov under Docket No. FAA-2024-2542.
FOR FURTHER INFORMATION CONTACT: Hye Yoon Jang, Aviation Safety
Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590;
phone: (206) 231-3758; email: [email protected].
SUPPLEMENTARY INFORMATION:
Background
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 to supersede AD 2008-10-01, Amendment 39-15507 (73 FR
24856, May 6, 2008), (AD 2008-10-01) and AD 2010-05-51, Amendment 39-
16265 (75 FR 22510, April 29, 2010) (AD 2010-05-51).
AD 2008-10-01 applied to Eurocopter France (now Airbus Helicopters)
Model EC120B helicopters with spherical thrust bearings, part number
(P/N) 7050A3622036 having serial number LK0130, LK0142, LK0155, or
LK0158, installed. AD 2008-10-01 required removing any identified
spherical thrust bearing and installing an airworthy spherical thrust
bearing. AD 2008-10-01 was prompted by Direction generale de l'aviation
civile France (DGAC), which was the aviation authority for France
before the European Aviation Safety Agency, AD F-2006-040, dated
February 15, 2006 (DGAC France AD F-2006-040), to address a batch of
non-conforming spherical thrust bearings. The FAA issued AD 2008-10-01
to prevent failure of a spherical thrust bearing during flight, which,
if not addressed, could cause the M/R system to separate from the
helicopter, which would be catastrophic.
AD 2010-05-51 applied to Eurocopter France (now Airbus Helicopters)
Model EC120B helicopters with a rotor hub P/N C622A1002103,
C622A1002104, or C622A1002105, installed. AD 2010-05-51 required
repetitively inspecting the rotor hub, and depending on the results,
sanding the area to inspect for cracks, and replacing the rotor hub if
cracks are found. AD 2010-05-51 was prompted by European Aviation
Safety Agency, which was the aviation authority for France after the
DGAC and before the European Union Aviation Safety Agency, Emergency AD
2010-0026-E, dated February 19, 2010 (European Aviation Safety Agency
Emergency AD 2010-0026-E), to address failure of a rotor hub attachment
area in one of the three drag damper fittings. The FAA issued AD 2010-
05-51 to prevent failure of a rotor hub, excessive vibrations, loss of
an M/R blade, and subsequent loss of control of the helicopter.
The NPRM published in the Federal Register on November 29, 2024 (89
FR 94623). The NPRM was prompted by EASA AD 2023-0083, dated April 19,
2023 (EASA AD 2023-0083) (also referred to as the MCAI), issued by
EASA, which is the Technical Agent for the Member States of the
European Union (including France), to supersede DGAC France AD F-2006-
040 and European Aviation Safety Agency Emergency AD 2010-0026-E. The
MCAI states that airworthiness limitations instructions are identified
as mandatory for continued airworthiness and that Revision 3 of AH
[Airbus Helicopters] EC 120 B Chapter 4 ALS, dated July 18, 2022, was
issued to introduce new, or more restrictive tasks, or both, including
incorporation of the requirements of DGAC France AD F-2006-040 and
European Aviation Safety Agency Emergency AD 2010-0026-E.
[[Page 14568]]
In the NPRM, the FAA proposed to require revising the ALS of the
existing MM or ICAs and the existing approved maintenance or inspection
program, as applicable, by incorporating new or more restrictive
actions and associated thresholds and intervals, including any life
limits, specified in EASA AD 2023-0083, as incorporated by reference,
except for any differences identified as exceptions in the regulatory
text of this AD and except as discussed under ``Differences Between
this AD and the EASA AD.''
You may examine the MCAI in the AD docket at regulations.gov under
Docket No. FAA-2024-2542.
Lastly, since the FAA issued AD 2008-10-01 and AD 2010-05-51,
Eurocopter France changed its name to Airbus Helicopters; this AD
reflects that change.
Discussion of Final Airworthiness Directive
Comments
The FAA received no comments on the NPRM or on the determination of
the costs.
Conclusion
These products have been approved by the aviation authority of
another country and are approved for operation in the United States.
Pursuant to the FAA's bilateral agreement with this State of Design
Authority, it has notified the FAA of the unsafe condition described in
the MCAI referenced above. The FAA reviewed the relevant data and
determined that air safety requires adopting this AD as proposed.
Accordingly, the FAA is issuing this AD to address the unsafe condition
on these products. Except for minor editorial changes, this AD is
adopted as proposed in the NPRM.
Material Incorporated by Reference Under 1 CFR Part 51
The FAA reviewed EASA AD 2023-0083, which requires replacing
components before exceeding their life limits and accomplishing all
applicable maintenance tasks within thresholds and intervals specified
in the ALS as defined within. Depending on the results of the
maintenance tasks, EASA AD 2023-0083 requires accomplishing corrective
action(s) or contacting AH [Airbus Helicopters] for approved
instructions and accomplishing those instructions.
Additionally, EASA AD 2023-0083 requires revising the Aircraft
Maintenance Programme (AMP) by incorporating the limitations, tasks,
and associated thresholds and intervals described in the specified ALS,
as applicable. Revising the AMP constitutes terminating action for the
requirement to record accomplishment of the actions of replacing
components before exceeding their life limits and accomplishing
maintenance tasks within thresholds and intervals specified in the
applicable ALS as required by EASA AD 2023-0083 for demonstration of AD
compliance on a continued basis.
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in the ADDRESSES section.
Differences Between This AD and the EASA AD
EASA AD 2023-0083 requires, as individual tasks, replacing certain
components before exceeding applicable life limits, accomplishing
certain maintenance tasks within thresholds and intervals as specified
in the ALS, as defined within, and depending on the results,
accomplishing corrective action(s), whereas this AD does not. EASA AD
2023-0083 also requires revising the approved AMP to incorporate the
limitations, tasks, and associated thresholds and intervals described
in that ALS within 12 months, whereas this AD requires revising the ALS
of the existing MM or ICAs and the existing approved maintenance or
inspection program, as applicable, by incorporating the limitations,
tasks, and associated thresholds and intervals described in that ALS
within 30 days, and clarifies that if the initial instance of an
incorporated limitation or threshold therein is reached before 30 days
after the effective date of this AD, you still have up to 30 days after
the effective date of this AD to accomplish the corresponding task.
Lastly, the material referenced in ``the ALS,'' as defined in EASA
AD 2023-0083, specifies contacting Airbus [Helicopters] if there is a
crack in the rotor hub, whereas this AD does not require contacting
Airbus Helicopters.
Costs of Compliance
The FAA estimates that this AD affects 65 helicopters of U.S.
registry. Labor rates are estimated at $85 per work-hour. Based on
these numbers, the FAA estimates the following costs to comply with
this AD.
Revising the ALS of the existing MM or ICAs and the existing
approved maintenance or inspection program, as applicable, takes 1
work-hour, at an estimated cost of $85 per helicopter and $5,525 for
the U.S. fleet.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA has determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by:
0
a. Removing Airworthiness Directive AD 2008-10-01, Amendment 39-15507
[[Page 14569]]
(73 FR 24856, May 6, 2008), and AD 2010-05-51, Amendment 39-16265 (75
FR 22510, April 29, 2010); and
0
b. Adding the following new airworthiness directive:
2025-05-12 Airbus Helicopters (Type Certificate previously held by
Eurocopter France): Amendment 39-22984; Docket No. FAA-2024-2542;
Project Identifier MCAI-2023-00611-R.
(a) Effective Date
This airworthiness directive (AD) is effective May 8, 2025.
(b) Affected ADs
This AD replaces AD 2008-10-01, Amendment 39-15507 (73 FR 24856,
May 6, 2008), and AD 2010-05-51, Amendment 39-16265 (75 FR 22510,
April 29, 2010).
(c) Applicability
This AD applies to Airbus Helicopters (type certificate
previously held by Eurocopter France) Model EC120B helicopters,
certificated in any category.
(d) Subject
Joint Aircraft System Component (JASC) Code: 6220, Main Rotor
Head.
(e) Unsafe Condition
This AD was prompted by new and more restrictive airworthiness
limitations. The FAA is issuing this AD to prevent failure of
certain parts, which if not addressed, could result in subsequent
loss of control of the helicopter.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Required Actions
Except as specified in paragraphs (h) and (i) of this AD: Comply
with all required actions and compliance times specified in, and in
accordance with, European Union Aviation Safety Agency AD 2023-0083,
dated April 19, 2023 (EASA AD 2023-0083).
(h) Exceptions to EASA AD 2023-0083
(1) Where EASA AD 2023-0083 refers to its effective date, this
AD requires using the effective date of this AD.
(2) This AD does not adopt paragraphs (1), (2), (4), and (5) of
EASA AD 2023-0083.
(3) Where paragraph (3) of EASA AD 2023-0083 specifies ``Within
12 months after the effective date of this AD, revise the approved
AMP,'' this AD requires replacing that text with ``Within 30 days
after the effective date of this AD, revise the airworthiness
limitations section of the existing maintenance manual or
instructions for continued airworthiness and the existing approved
maintenance or inspection program, as applicable.''
(4) Regarding ``the ALS'' as defined in EASA AD 2023-0083; where
the material referenced in ``the ALS'' in paragraph (3) of EASA AD
2023-0083 specifies contacting Airbus [Helicopters] if there is a
crack in the (main rotor head rotor) hub body, this AD does not
require contacting Airbus Helicopters.
(5) The initial compliance time for doing the tasks specified in
paragraph (3) of EASA AD 2023-0083 is on or before the applicable
``limitations'' and ``associated thresholds'' as incorporated by the
requirements of paragraph (3) of EASA AD 2023-0083 or within 30 days
after the effective date of this AD, whichever occurs later.
(6) This AD does not adopt the ``Remarks'' section of EASA AD
2023-0083.
(i) Provisions for Alternative Actions and Intervals
After the action required by paragraph (g) of this AD has been
done, no alternative actions and associated thresholds and
intervals, including life limits, are allowed unless they are
approved as specified in the provisions of the ``Ref. Publications''
section of EASA AD 2023-0083.
(j) Alternative Methods of Compliance (AMOCs)
(1) The Manager, International Validation Branch, FAA, has the
authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the manager of the International Validation Branch, send
it to the attention of the person identified in paragraph (k) of
this AD. If sending information directly to the manager of the
International Validation Branch, mail it to the address identified
in paragraph (k) of this AD or email to: [email protected]. If mailing
information, also submit information by email.
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
(k) Additional Information
For more information about this AD, contact Hye Yoon Jang,
Aviation Safety Engineer, 1600 Stewart Avenue, Suite 410, Westbury,
NY 11590; phone: (206) 231-3758; email: [email protected].
(l) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the material listed in this
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this material as applicable to do the actions
required by this AD, unless the AD specifies otherwise.
(i) European Union Aviation Safety Agency (EASA) AD 2023-0083,
dated April 19, 2023.
(ii) [Reserved]
(3) For EASA material identified in this AD, contact EASA,
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; phone: +49 221 8999
000; email: [email protected]; website: easa.europa.eu. You may
find the EASA material on the EASA website at ad.easa.europa.eu.
(4) You may view this material at the FAA, Office of the
Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 6N-
321, Fort Worth, TX 76177. For information on the availability of
this material at the FAA, call (817) 222-5110.
(5) You may view this material at the National Archives and
Records Administration (NARA). For information on the availability
of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected].
Issued on March 27, 2025.
Steven W. Thompson,
Acting Deputy Director, Compliance & Airworthiness Division, Aircraft
Certification Service.
[FR Doc. 2025-05708 Filed 4-2-25; 8:45 am]
BILLING CODE 4910-13-P