[Federal Register Volume 89, Number 189 (Monday, September 30, 2024)]
[Rules and Regulations]
[Pages 79418-79420]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2024-22258]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2024-1288; Project Identifier MCAI-2024-00063-T;
Amendment 39-22818; AD 2024-16-12]
RIN 2120-AA64
Airworthiness Directives; Airbus SAS Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for
certain Airbus SAS Model A330-243, -302, -343, and -941 airplanes. This
AD was prompted by a determination that a certain aft bulkhead cover
panel may have been made with a non-conforming material. This AD
requires replacing the aft bulkhead cover panel and prohibits the
installation of affected parts, as specified in a European Union
Aviation Safety Agency (EASA) AD, which is incorporated by reference.
The FAA is issuing this AD to address the unsafe condition on these
products.
DATES: This AD is effective November 4, 2024.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of November 4,
2024.
ADDRESSES:
[[Page 79419]]
AD Docket: You may examine the AD docket at regulations.gov under
Docket No. FAA-2024-1288; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this final rule, the mandatory continuing airworthiness
information (MCAI), any comments received, and other information. The
address for Docket Operations is U.S. Department of Transportation,
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200
New Jersey Avenue SE, Washington, DC 20590.
Material Incorporated by Reference:
For EASA material identified in this AD, contact EASA,
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999
000; email [email protected]; website easa.europa.eu. You may find
this material on the EASA website at ad.easa.europa.eu.
You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th Street,
Des Moines, WA. For information on the availability of this material at
the FAA, call 206-231-3195. It is also available at regulations.gov
under Docket No. FAA-2024-1288.
FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aviation Safety
Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590;
telephone: 206-231-3229; email: [email protected].
SUPPLEMENTARY INFORMATION:
Background
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 by adding an AD that would apply to certain Airbus SAS
Model A330-243, -302, -343, and -941 airplanes. The NPRM published in
the Federal Register on May 6, 2024 (89 FR 37142). The NPRM was
prompted by AD 2024-0023, dated January 23, 2024, issued by EASA, which
is the Technical Agent for the Member States of the European Union
(EASA AD 2024-0023) (also referred to as the MCAI). The MCAI states
that a certain aft bulkhead cover panel may have been made with a non-
conforming material. This panel is installed in galley G4 and does not
meet the heat release requirements. This condition, if not corrected,
represents a non-compliance with certification requirements that could
result in injury to occupants and reduced evacuation capacity from the
airplane in case of an emergency.
In the NPRM, the FAA proposed to require replacing the aft bulkhead
cover panel and prohibit the installation of affected parts, as
specified in EASA AD 2024-0023. The FAA is issuing this AD to address
the unsafe condition on these products.
You may examine the MCAI in the AD docket at regulations.gov under
Docket No. FAA-2024-1288.
Discussion of Final Airworthiness Directive
Comments
The FAA received a comment from Air Line Pilots Association,
International (ALPA), who supported the NPRM without change.
Conclusion
This product has been approved by the aviation authority of another
country and is approved for operation in the United States. Pursuant to
the FAA's bilateral agreement with this State of Design Authority, it
has notified the FAA of the unsafe condition described in the MCAI
referenced above. The FAA reviewed the relevant data, considered the
comment received, and determined that air safety requires adopting this
AD as proposed. Accordingly, the FAA is issuing this AD to address the
unsafe condition on this product. Except for minor editorial changes,
this AD is adopted as proposed in the NPRM. None of the changes will
increase the economic burden on any operator.
Material Incorporated by Reference Under 1 CFR Part 51
EASA AD 2024-0023 specifies replacing the aft bulkhead cover panel
installed in galley G4 and prohibits the installation of affected
parts. This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in ADDRESSES section.
Costs of Compliance
The FAA estimates that this AD affects 25 airplanes of U.S.
registry. The FAA estimates the following costs to comply with this AD:
Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
Labor cost Parts cost Cost per product Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
3.5 work-hours x $85 per hour = $298. Up to $123,000......... Up to $123,298......... Up to $3,082,450.
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Amendment
Accordingly, under the authority delegated to me by the
Administrator,
[[Page 79420]]
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
2024-16-12 Airbus SAS: Amendment 39-22818; Docket No. FAA-2024-1288;
Project Identifier MCAI-2024-00063-T.
(a) Effective Date
This airworthiness directive (AD) is effective November 4, 2024.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Airbus SAS Model A330-243, -302, -343, and -
941 airplanes, certificated in any category, as identified in
European Union Aviation Safety Agency (EASA) AD 2024-0023, dated
January 23, 2024 (EASA AD 2024-0023).
(d) Subject
Air Transport Association (ATA) of America Code 25, Equipment/
furnishings.
(e) Unsafe Condition
This AD was prompted by a determination that a certain aft
bulkhead cover panel may have been made with a non-conforming
material. The FAA is issuing this AD to address the non-conforming
aft bulkhead cover panel. The unsafe condition, if not addressed,
could result in injury to occupants, and reduced evacuation capacity
from the airplane in case of an emergency.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
Except as specified in paragraph (h) of this AD: Comply with all
required actions and compliance times specified in, and in
accordance with, EASA AD 2024-0023.
(h) Exceptions to EASA AD 2024-0023
(1) Where EASA AD 2024-0023 refers to its effective date, this
AD requires using the effective date of this AD.
(2) This AD does not adopt the ``Remarks'' section of EASA AD
2024-0023.
(i) Additional AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Validation Branch, FAA, has the authority to approve
AMOCs for this AD, if requested using the procedures found in 14 CFR
39.19. In accordance with 14 CFR 39.19, send your request to your
principal inspector or responsible Flight Standards Office, as
appropriate. If sending information directly to the manager of the
International Validation Branch, mail it to the address identified
in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your
appropriate principal inspector, or lacking a principal inspector,
the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain instructions from a manufacturer, the instructions must be
accomplished using a method approved by the Manager, International
Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design
Organization Approval (DOA). If approved by the DOA, the approval
must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by
paragraph (i)(2) of this AD: For material that contains procedures
or tests that are identified as RC, those procedures and tests must
be done to comply with this AD; any procedures or tests that are not
identified as RC are recommended. Those procedures and tests that
are not identified as RC may be deviated from using accepted methods
in accordance with the operator's maintenance or inspection program
without obtaining approval of an AMOC, provided the procedures and
tests identified as RC can be done and the airplane can be put back
in an airworthy condition. Any substitutions or changes to
procedures or tests identified as RC require approval of an AMOC.
(j) Additional Information
For more information about this AD, contact Vladimir Ulyanov,
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410,
Westbury, NY 11590; telephone: 206-231-3229; email:
[email protected].
(k) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the material listed in this
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this material as applicable to do the actions
required by this AD, unless this AD specifies otherwise.
(i) European Union Aviation Safety Agency (EASA) AD 2024-0023,
dated January 23, 2024.
(ii) [Reserved]
(3) For EASA material identified in this AD, contact EASA,
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221
8999 000; email [email protected]; website easa.europa.eu. You may
find this EASA material on the EASA website ad.easa.europa.eu.
(4) You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th
Street, Des Moines, WA. For information on the availability of this
material at the FAA, call 206-231-3195.
(5) You may view this material at the National Archives and
Records Administration (NARA). For information on the availability
of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations, or email [email protected].
Issued on August 2, 2024.
Peter A. White,
Deputy Director, Integrated Certificate Management Division, Aircraft
Certification Service.
[FR Doc. 2024-22258 Filed 9-27-24; 8:45 am]
BILLING CODE 4910-13-P