[Federal Register Volume 89, Number 162 (Wednesday, August 21, 2024)]
[Proposed Rules]
[Pages 67575-67577]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2024-18483]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2024-2025; Project Identifier MCAI-2024-00120-T]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for all Airbus SAS Model A321-251NX, -252NX, -253NX, -271NX, and -272NX 
airplanes. This proposed AD was prompted by the discovery during a 
quality review performed during manufacturing, that a torque strip 
indicator (material ``Dykem'') had been applied on the orifice fitting 
on certain slides' inflation reservoirs' venting holes. This proposed 
AD would require an inspection for discrepancies of affected parts 
(certain reservoirs having certain orifices) and replacement of 
discrepant affected parts, and would prohibit installing affected 
parts, as specified in a European Union Aviation Safety Agency (EASA) 
AD, which is proposed for incorporation by reference (IBR). The FAA is 
proposing this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by October 7, 
2024.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2024-2025; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For EASA material identified in this proposed AD, contact 
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; website easa.europa.eu. You may 
find this material on the EASA website at ad.easa.europa.eu. It is also 
available at regulations.gov under Docket No. FAA-2024-2025.
     You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Timothy Dowling, Aviation Safety 
Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone 206-231-3667; email [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2024-2025; 
Project Identifier MCAI-2024-00120-T'' at the beginning of your 
comments. The most helpful comments reference a specific portion of the 
proposal, explain the reason for any recommended change, and include 
supporting data. The FAA will consider all comments received by the 
closing date and may amend this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Timothy Dowling, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, 
Suite 410, Westbury, NY 11590; telephone 206-231-3667; email 
[email protected]. Any commentary that the FAA receives which 
is not specifically designated as CBI will be placed in the public 
docket for this rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2024-0057, dated February 28, 2024 
(EASA AD 2024-0057) (also referred to as the MCAI), to correct an 
unsafe condition for all Airbus SAS Model A321-251NX, -252NX, -253NX, -
271NX, and -272NX airplanes. The MCAI states that during a quality 
review performed during manufacturing, a quality escape was identified 
on the Model A321NX door 3 slide and offwing slide inflation 
reservoirs' venting holes, where a torque strip indicator (material 
``Dykem'') has been applied on the orifice fitting (clogging the vent 
hole). This condition, in combination with a slide reservoir pressure 
loss, if not detected and corrected, could lead to deployment in flight 
of a non-inflated slide, possibly resulting in damage to, and reduced 
control of, the airplane.
    The FAA is proposing this AD to address the unsafe condition on 
these products.

[[Page 67576]]

    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2024-2025.

Material Incorporated by Reference Under 1 CFR Part 51

    EASA AD 2024-0057 specifies a general visual inspection of affected 
parts (certain reservoirs having certain orifices) for discrepancies 
(the presence of ``Dykem'' material on the orifice fitting) and 
replacement of discrepant affected parts, and prohibits installing 
affected parts. This material is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in ADDRESSES.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this NPRM after determining that 
the unsafe condition described previously is likely to exist or develop 
in other products of the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2024-0057 described previously, except for any differences 
identified as exceptions in the regulatory text of this proposed AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, the 
FAA proposes to incorporate EASA AD 2024-0057 by reference in the FAA 
final rule. This proposed AD would, therefore, require compliance with 
EASA AD 2024-0057 in its entirety through that incorporation, except 
for any differences identified as exceptions in the regulatory text of 
this proposed AD. Using common terms that are the same as the heading 
of a particular section in EASA AD 2024-0057 does not mean that 
operators need comply only with that section. For example, where the AD 
requirement refers to ``all required actions and compliance times,'' 
compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2024-
0057. Service information required by EASA AD 2024-0057 for compliance 
will be available at regulations.gov under Docket No. FAA-2024-2025 
after the FAA final rule is published.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 227 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                           Labor cost                              Parts cost       product         operators
----------------------------------------------------------------------------------------------------------------
1 work-hour x $85 per hour = $85................................           $0              $85          $19,295
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary on-
condition action that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need this on-condition action:

                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
                                                             Cost per
              Labor cost                   Parts cost        product
------------------------------------------------------------------------
1 work-hour x $85 per hour = $85......      Negligible              $85
------------------------------------------------------------------------

    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this proposed AD may be covered under warranty, thereby reducing the 
cost impact on affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

[[Page 67577]]

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Airbus SAS: Docket No. FAA-2024-2025; Project Identifier MCAI-2024-
00120-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by October 7, 2024.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all Airbus SAS Model A321-251NX, -252NX, -
253NX, -271NX, and -272NX airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 25, Equipment/
Furnishings.

(e) Unsafe Condition

    This AD was prompted by the discovery during a quality review 
performed during manufacturing, that a torque strip indicator 
(material ``Dykem'') had been applied on the orifice fitting on 
certain slides' inflation reservoirs' venting holes. The FAA is 
issuing this AD to address blocked venting holes on the orifice 
fitting on an escape slide's inflation reservoir. The unsafe 
condition, if not addressed, could, in combination with a slide 
reservoir pressure loss, result in deployment in flight of a non-
inflated slide, possibly resulting in damage to, and reduced control 
of, the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) AD 
2024-0057, dated February 28, 2024 (EASA AD 2024-0057).

(h) Exceptions to EASA AD 2024-0057

    (1) Where EASA AD 2024-0057 refers to March 13, 2024, or its 
effective date, this AD requires using the effective date of this 
AD.
    (2) This AD does not adopt the ``Remarks'' section of EASA AD 
2024-0057.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the manager of the 
International Validation Branch, mail it to the address identified 
in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (i)(2) of this AD, if any service information referenced 
in EASA AD 2024-0057 contains paragraphs that are labeled as RC, the 
instructions in RC paragraphs, including subparagraphs under an RC 
paragraph, must be done to comply with this AD; any paragraphs, 
including subparagraphs under those paragraphs, that are not 
identified as RC are recommended. The instructions in paragraphs, 
including subparagraphs under those paragraphs, not identified as RC 
may be deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the instructions identified as RC can 
be done and the airplane can be put back in an airworthy condition. 
Any substitutions or changes to instructions identified as RC 
require approval of an AMOC.

(j) Additional Information

    For more information about this AD, contact Timothy Dowling, 
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 206-231-3667; email 
[email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this material as applicable to do the actions 
required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2024-0057, 
dated February 28, 2024.
    (ii) [Reserved]
    (3) For EASA AD 2024-0057, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; website easa.europa.eu. You may find this EASA 
AD on the EASA website at ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (5) You may view this material at the National Archives and 
Records Administration (NARA). For information on the availability 
of this material at NARA, visit www.archives.gov/federal-register/cfr/[email protected]">www.archives.gov/federal-register/cfr/[email protected].

    Issued on August 12, 2024.
Peter A. White,
Deputy Director, Integrated Certificate Management Division, Aircraft 
Certification Service.
[FR Doc. 2024-18483 Filed 8-20-24; 8:45 am]
BILLING CODE 4910-13-P