[Federal Register Volume 89, Number 161 (Tuesday, August 20, 2024)]
[Rules and Regulations]
[Pages 67257-67261]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2024-18625]



 ========================================================================
 Rules and Regulations
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains regulatory documents 
 having general applicability and legal effect, most of which are keyed 
 to and codified in the Code of Federal Regulations, which is published 
 under 50 titles pursuant to 44 U.S.C. 1510.
 
 The Code of Federal Regulations is sold by the Superintendent of Documents. 
 
 ========================================================================
 

  Federal Register / Vol. 89 , No. 161 / Tuesday, August 20, 2024 / 
Rules and Regulations  

[[Page 67257]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2024-0231; Project Identifier AD-2023-01037-T; 
Amendment 39-22779; AD 2024-13-05]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This AD 
was prompted by a report of heat damage on multiple engine inlets 
around the engine anti-ice (EAI) duct within the inlet aft compartment. 
This AD requires doing a records check and updating the operator's 
existing minimum equipment list (MEL), inspecting the left and right 
engine inlet cowl assembly for signs of heat damage around the EAI 
duct, installing or replacing the EAI duct seals, repairing any damage, 
and replacing the engine inlet if necessary. This AD also prohibits the 
installation of engine inlets under certain conditions. The FAA is 
issuing this AD to address the unsafe condition on these products.

DATES: This AD is effective September 24, 2024.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of September 24, 
2024.

ADDRESSES: 
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2024-0231; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this final rule, any comments received, and other 
information. The address for Docket Operations is U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.
    Material Incorporated by Reference:
     For Boeing material identified in this AD, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; website myboeingfleet.com.
     You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195. It is also available at regulations.gov under 
Docket No. FAA-2024-0231.

FOR FURTHER INFORMATION CONTACT: Tak Kobayashi, Aviation Safety 
Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
206-231-3553; email [email protected].

SUPPLEMENTARY INFORMATION:

Background

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to all The Boeing Company 
(Boeing) Model 787-8, 787-9, and 787-10 airplanes. The NPRM published 
in the Federal Register on February 20, 2024 (89 FR 12785). The NPRM 
was prompted by a report of heat damage on multiple engine inlets 
around the EAI duct within the inlet aft compartment. A subsequent 
investigation found that the seals between the inner and outer ducts 
and between the outer duct and the aft compartment were degraded or 
missing, which led to EAI air leaking into the aft compartment, 
exposing inlet components to high temperatures.
    In the NPRM, the FAA proposed to require doing a records check and 
updating the operator's existing MEL, inspecting the left and right 
engine inlet cowl assembly for signs of heat damage around the EAI 
duct, installing or replacing the EAI duct seals, repairing any damage, 
and replacing the engine inlet if necessary. The FAA is issuing this AD 
to address reduced structural strength and departure of the inlet from 
the airplane, resulting in subsequent loss of continued safe flight and 
landing or injury to occupants from a departed inlet contacting the 
airplane.

Discussion of Final Airworthiness Directive

Comments

    The FAA received comments from nine commenters. The commenters were 
the Air Line Pilots Association, International (ALPA), American 
Airlines (AAL), Boeing, British Airways, Qantas, United Airlines (UAL), 
and three individual commenters.
    ALPA and two individuals supported the NPRM without change.
    One commenter expressed concern about the effect on safety of 
certain internal Boeing practices. This comment is outside the scope of 
the NPRM.
    The following presents the remaining comments received on the NPRM 
and the FAA's response to each comment.

Request for Additional Definition of a Serviceable Engine Inlet

    In the NPRM, the FAA proposed to require complying with Boeing 
Alert Requirements Bulletin B787-81205-SB540023-00 RB, Issue 001, dated 
September 22, 2023, or B787-81205-SB540024-00 RB, Issue 001, dated 
September 22, 2023, both of which specify replacing the engine inlet 
with a new or serviceable engine inlet under certain conditions. The 
requirements bulletins define a serviceable engine inlet as an engine 
inlet that has been inspected and had applicable corrective actions 
done in accordance with the requirements bulletins. AAL requested that 
the FAA consider, as an alternative serviceable engine inlet, one that 
has been inspected and had applicable corrective actions done in 
accordance with Collins Service Bulletin 787-G71-013, Revision 00, 
dated August 3, 2023, or later approved revisions.
    The FAA does not agree. The instructions in Collins Aerospace 
Service Bulletin 787-G71-013 or 787-R71-034 are insufficient to ensure 
a damaged engine inlet is restored to a serviceable condition. Where 
indications of heat damage are discovered on metallic components, the 
Collins service bulletins specify performing conductivity and hardness 
tests. When the results of the conductivity or hardness test are 
outside acceptable limits, the Collins service bulletins specify 
submitting the test results to Collins with no further

[[Page 67258]]

procedures or instructions to accomplish a repair. The FAA has not 
changed this AD in this regard.

Request for Inspection Instructions in the AD

    In the NPRM, the FAA proposed to require complying with Boeing 
Alert Requirements Bulletin B787-81205-SB540023-00 RB, Issue 001, dated 
September 22, 2023, or B787-81205-SB540024-00 RB, Issue 001, dated 
September 22, 2023, both of which specify inspecting the engine inlet 
cavity in accordance with those requirements bulletins and with Collins 
Service Bulletin 787-G71-013 or 787-R71-034, both dated August 3, 2023, 
or later-approved revisions. AAL requested that the FAA revise the AD 
by adding the inspection procedures from the Boeing and Collins 
bulletins instead of incorporating those procedures by reference. As 
support for its request, AAL stated the bulletins are not readily 
available and accessible to the line mechanics.
    The FAA disagrees with AAL's request to revise the proposed AD to 
include the inspection instructions instead of incorporating the 
service information by reference. Including all inspection instructions 
in the AD is inefficient and defeats the purpose of incorporation by 
reference. The referenced Boeing and Collins service bulletins are 
readily available to operators through their normal courses of business 
or from the manufacturers. The FAA has not changed this AD in this 
regard.

Request for Later-Approved Revisions of Structural Repair Manual

    In the NPRM, the FAA proposed to require complying with Boeing 
Requirements Bulletin B787-81205-SB540023-00 RB, Issue 001, dated 
September 22, 2023, or B787-81205-SB540024-00 RB, Issue 001, dated 
September 22, 2023, both of which reference specific sections, by 
revision number, of the Boeing structural repair manual (SRM) for 
certain information. Boeing and UAL requested that the FAA revise the 
proposed AD to allow the use of later-approved revisions of the SRM. 
Boeing stated that operators do not recall historical SRM revisions, 
and therefore they can incorporate only the latest revision of the SRM 
at the time of accomplishment.
    The FAA disagrees with the request. The SRM sections cited in the 
requirements bulletins define heat damage in a way that the FAA finds 
will address the unsafe condition in this AD. If future revisions of 
those SRM sections also define heat damage in a way that adequately 
addresses the unsafe condition in this AD, the commenters can request 
approval of those sections as an alternative method of compliance 
(AMOC). The FAA has not changed this AD as a result of this comment.

Request for Change to Background and Unsafe Condition

    Boeing requested that the FAA revise the Background section of the 
NPRM and paragraph (e) of the proposed AD to clarify that partially 
degraded seals were found in addition to missing seals.
    The FAA agrees and has revised the preamble and the unsafe 
condition statement in paragraph (e) of this AD accordingly.

Request for Clarification of Description of Proposed Requirements

    The preamble of the NPRM explained that the FAA proposed to require 
doing a records check and updating the operator's MEL, among other 
actions. Boeing requested that the FAA revise the preamble to clarify 
that the update is actually within the Dispatch Deviations Guide (DDG) 
and not with any actual equipment on the list. Boeing stated that this 
change would avoid confusion regarding the actual MEL changes.
    The FAA disagrees with the request. This AD requires revising the 
operator's MEL by incorporating the DDG update. Although the commenter 
is correct that the MEL revision is not intended to change any 
equipment listed on the MEL, since the DDG is part of the MEL, the 
statement in the NPRM is accurate. The FAA has not changed this AD in 
this regard.

Request for Corrected Paragraph Reference

    Boeing, AAL, and UAL requested that the FAA revise paragraph (h)(3) 
of the proposed AD, which incorrectly referred to paragraph (k) for 
approval of AMOCs. The correct reference is paragraph (j).
    The FAA agrees and has revised paragraph (h) of this AD 
accordingly.

Request To Extend Compliance Time for Inspection

    In the NPRM, the FAA proposed to require complying with Boeing 
Requirements Bulletin B787-81205-SB540023-00 RB, Issue 001, dated 
September 22, 2023, or B787-81205-SB540024-00 RB, Issue 001, dated 
September 22, 2023. Table 10 of the requirements bulletins specifies 
doing an inspection of the engine inlet cavity at or prior to the 
expiration of the time interval under MEL 30-21-01-02 or MEL 30-21-01-
07 (the interval for repair category C, which is 10 consecutive 
calendar days (240 hours) with a single extension, if authorized, as 
defined in the DDG).
    British Airways requested that the FAA revise the compliance time 
to allow an additional 125 days after the expiration of the MEL 
interval period to do the inspections and any corrective actions. 
British Airways acknowledged the safety concerns surrounding inlets 
that have been exposed to high temperatures during the time period 
allowed under MEL 30-21-01-02 or MEL 30-21-01-07 but stated the 
compliance time in the NPRM would cause considerable maintenance 
concerns for operators as it does not give sufficient time to plan for 
and carry out the required actions in a controlled environment.
    The FAA disagrees with the request for a longer compliance time. 
The FAA anticipates the potential structural damage incurred by the 
airplane due to dispatch under the MEL to increase as the engine inlet 
accumulates more operational time under those specific MEL conditions. 
Since accumulated structural damage on each engine inlet is unknown, 
the FAA determined that the inspection of the engine inlet at the 
completion of the dispatch interval period was necessary. Operators who 
can justify that, after completion of the MEL dispatch interval period, 
an engine inlet can maintain its structural integrity over a longer 
time period may propose that time period as an alternative method of 
compliance under the process specified in paragraph (j) of this AD.

Request To Change Location of MEL Inspection Procedure

    In the NPRM, the FAA proposed to require complying with Boeing 
Requirements Bulletin B787-81205-SB540023-00 RB, Issue 001, dated 
September 22, 2023, or B787-81205-SB540024-00 RB, Issue 001, dated 
September 22, 2023, both of which specify revising the operator's MEL 
by incorporating the DDG 30-21-01-02 update. The MEL, with the DDG 
update incorporated, allows dispatch with inoperative equipment 
specified under items 30-21-01-02 and 30-21-01-07 provided the engine 
inlet cavity is inspected and applicable corrective actions are taken 
in accordance with the requirements bulletins and with Collins Service 
Bulletin 787-G71-013 or 787-R71-034, both dated August 3, 2023, or 
later approved revisions.
    Qantas and UAL requested that the FAA change the location of the 
required inspection instructions for dispatch under the MEL from the 
bulletins to the airplane maintenance manual (AMM).

[[Page 67259]]

Alternatively, UAL requested that the inspection instructions be 
included in the DDG update itself instead of having the DDG refer to 
the service bulletins. Qantas, UAL, and British Airways all stated that 
operators' maintenance systems are not set up to provide maintenance 
personnel with access to service bulletins. Qantas expressed a concern 
that maintenance personnel could inadvertently fail to carry out the 
required inspection as part of the MEL process.
    The FAA disagrees. The concern about accessibility of the 
requirements bulletins to maintenance personnel is not unique to this 
AD. The FAA commonly issues ADs that mandate service documents 
containing instructions that must be carried out to resolve an unsafe 
condition. Operators and repair stations are required to provide those 
mandatory service documents to their maintenance personnel. In 
addition, for this AD, the requirement through the MEL is necessary 
because compliance may be based on the need for dispatch with 
inoperative equipment. The FAA has not changed this AD as a result of 
these comments.

Request for Instructions for Engine Inlets With Unknown History

    Qantas requested that the FAA clarify how to comply with the AD for 
engine inlets that are not installed on an airplane and for which the 
last installation is unknown. Qantas stated that since engine inlets 
can be moved from airplane to airplane, operators may not know whether 
an engine inlet was installed on airplane and dispatched under the MEL.
    The requirements bulletins specify that, if an operator cannot 
determine whether the airplane was dispatched under MEL 30-21-01-02 or 
MEL 30-21-01-07, the engine inlet must be inspected or replaced. No 
change to this AD is necessary as a result of this comment.

Request for Information To Determine Heat Damage of Primer

    UAL stated that the SRM sections referenced in the requirements 
bulletins do not provide pass/fail criteria for the amount of 
discoloration when assessing for heat damage. UAL requested 
clarification of whether any browning of primer would be an indication 
of a missing seal.
    The commenter is correct that the SRM sections referenced in the 
requirements bulletins do not provide pass/fail criteria. However, the 
SRM sections do provide appropriate information to determine heat 
damage. Under the criteria in the SRM, the FAA expects that any 
discoloration of primer would be treated as evidence of heat damage. 
The FAA has not changed this AD as a result of this comment.

Conclusion

    The FAA reviewed the relevant data, considered any comments 
received, and determined that air safety requires adopting this AD as 
proposed. Accordingly, the FAA is issuing this AD to address the unsafe 
condition on these products. This AD is adopted as proposed in the 
NPRM. None of the changes will increase the economic burden on any 
operator.

Material Incorporated by Reference Under 1 CFR Part 51

    The FAA reviewed Boeing Alert Requirements Bulletin B787-81205-
SB540023-00 RB, Issue 001, dated September 22, 2023; and Boeing Alert 
Requirements Bulletin B787-81205-SB540024-00 RB, Issue 001, dated 
September 22, 2023. This material specifies procedures for 
incorporating (or verifying incorporation of) an updated DDG for item 
30-21-01-02 into the operator's existing MEL, checking records to 
determine whether the inlet has been dispatched under MEL item 30-21-
01-02 or 30-21-01-07 before incorporation of the DDG 30-21-01-02 
update, and applicable related investigative and corrective actions, 
including general visual inspection for signs of heat damage around the 
EAI duct, conductivity measurement and hardness test of areas with heat 
damage, replacement/installation of the periseal and aft seal, and 
repair or replacement of the engine inlet. These documents are distinct 
since they apply to different airplane configurations. This material is 
reasonably available because the interested parties have access to it 
through their normal course of business or by the means identified in 
ADDRESSES.

Interim Action

    The FAA considers that this AD would be an interim action. An 
investigation is ongoing. If final action is later identified, the FAA 
might consider further rulemaking then.

Costs of Compliance

    The FAA estimates that this AD affects 110 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
               Action                        Labor cost           Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
MEL update and records check........  5 work-hours x $85 per               $0             $425          $46,750
                                       hour = $425.
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any investigative 
actions or repairs/replacements that would be required based on the 
results of the records check. The agency has no way of determining the 
number of airplanes that might need these actions:

                                               On-Condition Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                     Cost per
                  Action                                Labor cost                 Parts cost        product
----------------------------------------------------------------------------------------------------------------
Inspection................................  3 work-hours x $85 per hour = $255              $0             $255
----------------------------------------------------------------------------------------------------------------

    The FAA has received no definitive data on which to base the cost 
estimates for the conductivity measurement, the hardness test, inlet 
replacement, and installation of a new periseal and aft seal, as 
specified in this AD.

[[Page 67260]]

    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this AD may be covered under warranty, thereby reducing the cost impact 
on affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2024-13-05 The Boeing Company: Amendment 39-22779; Docket No. FAA-
2024-0231; Project Identifier AD-2023-01037-T.

(a) Effective Date

    This airworthiness directive (AD) is effective September 24, 
2024.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all The Boeing Company Model 787-8, 787-9, 
and 787-10 airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 54, Nacelles/
pylons.

(e) Unsafe Condition

    This AD was prompted by a report of heat damage on multiple 
engine inlets around the engine anti-ice (EAI) duct within the inlet 
aft compartment due to missing or degraded seals between the inner 
and outer ducts and between the outer duct and the aft compartment. 
The FAA is issuing this AD to address EAI air leaking into aft 
compartment exposing inlet components to high temperatures, which 
could result in damage around the EAI duct. This condition, if not 
addressed, could lead to reduced structural strength and departure 
of the inlet from the airplane, resulting in subsequent loss of 
continued safe flight and landing or injury to occupants from a 
departed inlet contacting the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Except as specified by paragraph (h) of this AD: At the 
applicable times specified in the ``Compliance'' paragraph of Boeing 
Alert Requirements Bulletin B787-81205-SB540023-00 RB or B787-81205-
SB540024-00 RB, both Issue 001 and both dated September 22, 2023, as 
applicable, do all applicable actions identified in, and in 
accordance with, the Accomplishment Instructions of Boeing Alert 
Requirements Bulletin B787-81205-SB540023-00 RB or B787-81205-
SB540024-00 RB, both Issue 001 and both dated September 22, 2023, as 
applicable.

    Note 1 to paragraph (g): Guidance for accomplishing the actions 
required by this AD can be found in Boeing Alert Service Bulletin 
B787-81205-SB540023-00, dated September 22, 2023, which is referred 
to in Boeing Alert Requirements Bulletin B787-81205-SB540023-00 RB, 
Issue 001, dated September 22, 2023.


    Note 2 to paragraph (g): Guidance for accomplishing the actions 
required by this AD can also be found in Boeing Alert Service 
Bulletin B787-81205-SB540024-00, dated September 22, 2023, which is 
referred to in Boeing Alert Requirements Bulletin B787-81205-
SB540024-00 RB, Issue 001, dated September 22, 2023.

(h) Exceptions to Service Information Specifications

    (1) Where the ``Boeing Recommended Compliance Time'' column in 
the tables under the ``Compliance'' paragraph of Boeing Alert 
Requirements Bulletin B787-81205-SB540023-00 RB, Issue 001, dated 
September 22, 2023, use the phrase ``the Issue 001 date of 
Requirements Bulletin B787-81205-SB540023 RB,'' this AD requires 
using the effective date of this AD.
    (2) Where the ``Boeing Recommended Compliance Time'' columns in 
the tables under the ``Compliance'' paragraph of Boeing Alert 
Requirements Bulletin B787-81205-SB540024-00 RB, Issue 001, dated 
September 22, 2023, use the phrase ``the Issue 001 date of 
Requirements Bulletin B787-81205-SB540024 RB,'' this AD requires 
using the effective date of this AD.
    (3) Where Boeing Alert Requirements Bulletin B787-81205-
SB540023-00 RB, Issue 001, dated September 22, 2023, and Boeing 
Alert Requirements Bulletin B787-81205-SB540024-00 RB, Issue 001, 
dated September 22, 2023, specify contacting Boeing for repair 
instructions, this AD requires doing the repair before further 
flight, using a method approved in accordance with the procedures 
specified in paragraph (j) of this AD.

(i) Parts Installation Prohibition

    After accomplishment of all applicable actions required by 
paragraph (g) of this AD on an airplane, no person may install on 
that airplane any engine inlet that meets a condition specified in 
paragraph (i)(1) or (2) of this AD, unless the engine inlet has been 
inspected and applicable corrective actions taken as specified in 
Boeing Alert Requirements Bulletin B787-81205-SB540023-00 RB, Issue 
001, dated September 22, 2023; or Boeing Alert Requirements Bulletin 
B787-81205-SB540024-00 RB, Issue 001, dated September 22, 2023.
    (1) If the engine inlet was installed on an airplane that was 
dispatched under a dispatch deviation for the operator's existing 
minimum equipment list (MEL) item 30-21-01-02 or 30-21-01-07 prior 
to incorporation of Boeing 787 Dispatch Deviation Guide (DDG) 30-21-
01-02, as required by this AD.
    (2) If the engine inlet was installed on an airplane for which 
dispatch under a dispatch deviation for the operator's existing MEL 
item 30-21-01-02 or 30-21-01-07 prior to incorporation of Boeing 787 
DDG 30-21-01-02, as required by this AD, cannot be determined.

(j) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, AIR-520, Continued Operational Safety Branch, 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or 
responsible Flight Standards Office, as

[[Page 67261]]

appropriate. If sending information directly to the manager of the 
certification office, send it to the attention of the person 
identified in paragraph (k) of this AD. Information may be emailed 
to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the responsible Flight Standards Office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by The Boeing Company Organization Designation 
Authorization (ODA) that has been authorized by the Manager, AIR-
520, Continued Operational Safety Branch, FAA, to make those 
findings. To be approved, the repair method, modification deviation, 
or alteration deviation must meet the certification basis of the 
airplane, and the approval must specifically refer to this AD.

(k) Related Information

    For more information about this AD, contact Tak Kobayashi, 
Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA 
98198; telephone 206-231-3553; email [email protected].

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the material listed in this paragraph 
under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this material as applicable to do the actions 
required by this AD, unless the AD specifies otherwise.
    (i) Boeing Alert Requirements Bulletin B787-81205-SB540023-00 
RB, Issue 001, dated September 22, 2023.
    (ii) Boeing Alert Requirements Bulletin B787-81205-SB540024-00 
RB, Issue 001, dated September 22, 2023.
    (3) For Boeing material identified in this AD, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; website myboeingfleet.com.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (5) You may view this material at the National Archives and 
Records Administration (NARA). For information on the availability 
of this material at NARA, visit www.archives.gov/federal-register/cfr/[email protected]">www.archives.gov/federal-register/cfr/[email protected].

    Issued on July 29, 2024.
Peter A. White,
Deputy Director, Integrated Certificate Management Division, Aircraft 
Certification Service.
[FR Doc. 2024-18625 Filed 8-19-24; 8:45 am]
BILLING CODE 4910-13-P