[Federal Register Volume 89, Number 154 (Friday, August 9, 2024)]
[Proposed Rules]
[Pages 65267-65270]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2024-17362]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2024-2007; Project Identifier MCAI-2023-01270-T]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc., Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for all Bombardier, Inc., Model BD-100-1A10 airplanes. This proposed AD 
was prompted by a determination that new or more restrictive 
maintenance tasks are necessary. This proposed AD would require 
revising the existing maintenance or inspection program, as applicable, 
to incorporate new or more restrictive maintenance tasks. The FAA is 
proposing this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by September 
23, 2024.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2024-2007; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For Bombardier, Inc. material identified in this proposed 
AD, contact Bombardier Business Aircraft Customer Response Center, 400 
C[ocirc]te Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, Canada; 
telephone 514-855-2999; email bombardier.com">ac.yul@aero.bombardier.com; website 
bombardier.com.
     You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th Street, 
Des Moines, WA. For information on the availability of this material at 
the FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Steven Dzierzynski, Aviation Safety 
Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone: 516-228-7300; email: [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2024-2007; Project Identifier 
MCAI-2023-01270-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
the proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other

[[Page 65268]]

information as described in 14 CFR 11.35, the FAA will post all 
comments received, without change, to regulations.gov, including any 
personal information you provide. The agency will also post a report 
summarizing each substantive verbal contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Steven Dzierzynski, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, 
Suite 410, Westbury, NY 11590; telephone: 516-228-7300; email: [email protected]. Any commentary that the FAA receives which is not 
specifically designated as CBI will be placed in the public docket for 
this rulemaking.

Background

    Transport Canada, which is the aviation authority for Canada, has 
issued Transport Canada AD CF-2023-78, dated December 19, 2023 
(Transport Canada AD CF-2023-78) (also referred to as the MCAI), to 
correct an unsafe condition for all Bombardier, Inc., Model BD-100-1A10 
airplanes. The MCAI states that airplanes could experience misleading 
electrical system status indications (push button annunciators (PBA) 
and engine indicating and crew alerting system (EICAS)) as a result of 
contamination of electrical contacts in the left-hand (LH) direct 
current power center (DCPC) internal communication data bus. The MCAI 
states that new or more restrictive maintenance tasks have been 
developed to rectify lower time LH DCPC units not addressed by 
previously issued AD's.
    The FAA is proposing this AD to address erratic indications, which 
could cause the flightcrew to turn off fully operational electrical 
power sources, leading to partial or complete loss of electrical power. 
The unsafe condition, if not addressed, could result in loss of flight 
displays and reduced controllability of the airplane. You may examine 
the MCAI in the AD docket at regulations.gov under Docket No. FAA-2024-
2007.

Material Incorporated by Reference Under 1 CFR Part 51

    The FAA reviewed the following documents:
     Task 24-61-01-101, ``Restoration of the left DC Power 
Center (DCPC) (Pre SB100-24-30),'' Section 5-10-20, ``Time Limits--
Supplementary Limitations,'' of Part 2, ``Airworthiness Limitations'', 
of the Bombardier Challenger 300 BD-100 Time Limits/Maintenance Checks, 
Revision 24, dated August 9, 2023.
     Task 24-61-01-101, ``Restoration of the Left DC Power 
Center (DCPC) (Pre SB350-24-005),'' Section 5-10-20, ``Time Limits--
Supplementary Limitations,'' of Part 2, ``Airworthiness Limitations,'' 
of the Bombardier Challenger 350 BD-100 Time Limits/Maintenance Checks, 
Revision 14, dated August 9, 2023.
    This material specifies new or more restrictive airworthiness 
limitations for safe life limits.
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, the 
FAA has been notified of the unsafe condition described in the MCAI and 
material referenced above. The FAA is issuing this NPRM after 
determining that the unsafe condition described previously is likely to 
exist or develop on other products of the same type design.

Proposed Requirements of This NPRM

    This proposed AD would require revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive maintenance tasks.
    This proposed AD would require revisions to certain operator 
maintenance documents to include new actions (e.g., inspections). 
Compliance with these actions is required by 14 CFR 91.403(c). For 
airplanes that have been previously modified, altered, or repaired in 
the areas addressed by this proposed AD, the operator may not be able 
to accomplish the actions described in the revisions. In this 
situation, to comply with 14 CFR 91.403(c), the operator must request 
approval for an alternative method of compliance according to paragraph 
(i)(1) of this proposed AD.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 356 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:
    The FAA has determined that revising the maintenance or inspection 
program takes an average of 90 work-hours per operator, although the 
agency recognizes that this number may vary from operator to operator. 
Since operators incorporate maintenance or inspection program changes 
for their affected fleet(s), the FAA has determined that a per-operator 
estimate is more accurate than a per-airplane estimate. Therefore, the 
agency estimates the average total cost per operator to be $7,650 (90 
work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and

[[Page 65269]]

    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Bombardier, Inc.: Docket No. FAA-2024-2007; Project Identifier MCAI-
2023-01270-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by September 23, 2024.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all Bombardier, Inc., Model BD-100-1A10 
airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 24, Electrical 
Power.

(e) Unsafe Condition

    This AD was prompted by a determination that new or more 
restrictive maintenance tasks are necessary. The FAA is issuing this 
AD to address to address erratic indications, which could cause the 
flightcrew to turn off fully operational electrical power sources, 
leading to partial or complete loss of electrical power. The unsafe 
condition, if not addressed, could result in loss of flight displays 
and reduced controllability of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Maintenance or Inspection Program Revision

    Within 60 days after the effective date of this AD, revise the 
existing maintenance or inspection program, as applicable, to 
incorporate the information specified in the tasks specified in 
figure 1 to paragraph (g) of this AD, of Part 2, ``Airworthiness 
Limitations,'' of the applicable Time Limits/Maintenance Checks 
(TLMC) manual. The initial compliance time for doing the tasks is at 
the interval specified in the applicable TLMC manual specified in 
figure 1 to paragraph (g) of this AD, or within 60 days after the 
effective date of this AD, whichever occurs later.

Figure 1 to paragraph (g)--Time Limits--Supplementary Limitations Tasks
[GRAPHIC] [TIFF OMITTED] TP09AU24.000

    Note 1 to paragraph (g): The asterisk (or ``one star'') with the 
last three digits of the task numbers listed in figure 1 to 
paragraph (g) of this AD indicates that the task is an airworthiness 
limitation task.

(h) No Alternative Actions, Intervals

    After the existing maintenance or inspection program has been 
revised as required by paragraph (g) of this AD, no alternative 
actions (e.g., inspections) or intervals may be used unless the 
actions and intervals are approved as an alternative method of 
compliance (AMOC) in accordance with the procedures specified in 
paragraph (i)(1) of this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the manager of the 
International Validation Branch, mail it to the address identified 
in paragraph (j) of this AD. Information may be emailed to: 9-AVS-
[email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or Transport Canada; or Bombardier, Inc.'s 
Transport Canada Design Approval Organization (DAO). If approved by 
the DAO, the approval must include the DAO-authorized signature.

(j) Additional Information

    For more information about this AD, contact Steven Dzierzynski, 
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone: 516-228-7300; email: [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the material listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this material as applicable to do the actions 
required by this AD, unless this AD specifies otherwise.
    (i) Task 24-61-01-101, ``Restoration of the left DC Power Center 
(DCPC) (Pre SB100-24-30),'' Section 5-10-20, ``Time Limits--
Supplementary Limitations,'' of Part 2, ``Airworthiness 
Limitations'', of the Bombardier Challenger 300 BD-100 Time Limits/
Maintenance Checks, Revision 24, dated August 9, 2023.
    (ii) Task 24-61-01-101, ``Restoration of the Left DC Power 
Center (DCPC) (Pre SB350-24-005),'' Section 5-10-20, ``Time Limits--
Supplementary Limitations,'' of Part 2, ``Airworthiness 
Limitations,'' of the Bombardier Challenger 350 BD-100 Time

[[Page 65270]]

Limits/Maintenance Checks, Revision 14, dated August 9, 2023.
    (3) For Bombardier Inc. material identified in this AD, contact 
Bombardier Business Aircraft Customer Response Center, 400 
C[ocirc]te Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, Canada; 
telephone 514 855-2999; email bombardier.com">ac.yul@aero.bombardier.com; website 
bombardier.com.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th 
Street, Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195.
    (5) You may view this material at the National Archives and 
Records Administration (NARA). For information on the availability 
of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected].

    Issued on July 31, 2024.
Victor Wicklund,
Deputy Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2024-17362 Filed 8-8-24; 8:45 am]
BILLING CODE 4910-13-P