[Federal Register Volume 89, Number 101 (Thursday, May 23, 2024)]
[Proposed Rules]
[Pages 45610-45612]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2024-11163]



[[Page 45610]]

=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2024-1474; Project Identifier MCAI-2023-01014-T]
RIN 2120-AA64


Airworthiness Directives; Airbus Canada Limited Partnership (Type 
Certificate Previously Held by C Series Aircraft Limited Partnership 
(CSALP)) Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-
500-1A11 airplanes. This proposed AD was prompted by reports that the 
pylon-to-wing area motive flow flexible fuel line assemblies may have 
been installed incorrectly. This proposed AD would require inspecting 
the motive flow flexible fuel line assemblies and corrective actions, 
as specified in a Transport Canada AD, which is proposed for 
incorporation by reference (IBR). The FAA is proposing this AD to 
address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by July 8, 
2024.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2024-1474; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For material, contact Transport Canada, Transport Canada 
National Aircraft Certification, 159 Cleopatra Drive, Nepean, Ontario 
K1A 0N5, Canada; telephone 888-663-3639; email 
[email protected]. You may 
find this material on the Transport Canada website tc.canada.ca/en/
aviation. It is also available at regulations.gov under Docket No. FAA-
2024-1474.
     You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th Street, 
Des Moines, WA. For information on the availability of this material at 
the FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Joseph Catanzaro, Aviation Safety 
Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone 516-228-7366; email [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2024-1474; Project Identifier 
MCAI-2023-01014-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Joseph Catanzaro, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, 
Suite 410, Westbury, NY 11590; telephone 516-228-7366; email 
[email protected]. Any commentary that the FAA receives which is 
not specifically designated as CBI will be placed in the public docket 
for this rulemaking.

Background

    Transport Canada, which is the aviation authority for Canada, has 
issued Transport Canada AD CF-2023-64, dated September 18, 2023 
(Transport Canada AD CF-2023-64) (also referred to as the MCAI), to 
correct an unsafe condition for certain Airbus Canada Limited 
Partnership Model BD-500-1A10 and BD-500-1A11 airplanes. The MCAI 
states that reports have been received indicating that the pylon-to-
wing area motive flow flexible fuel line assemblies may have been 
installed incorrectly, potentially resulting in a twist to the motive 
flow flexible fuel line. A twisted motive flow flexible fuel line may 
contact and abrade the motive flow flexible fuel line shroud, which may 
then abrade the fuel line, resulting in a fuel leak. Electrical harness 
connectors in the area are a potential ignition source and pose a risk 
of fire.
    Transport Canada previously issued AD CF-2021-09, dated March 11, 
2021 (Transport Canada AD CF-2021-09), to require an inspection and, if 
necessary, replacement of later configurations of left and right motive 
flow flexible fuel line assemblies. Transport Canada AD CF-2021-09 
corresponds to FAA AD 2021-17-07, Amendment 39-21690 (86 FR 44600, 
August 13, 2021). This proposed AD would add airplanes with an early 
configuration of motive flow flexible fuel lines that AD 2021-17-07 did 
not address.
    The FAA is proposing this AD to address the unsafe condition on 
these products.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2024-1474.

Related Service Information Under 1 CFR Part 51

    Transport Canada AD CF-2023-64 specifies procedures for a general 
visual inspection of the left and right motive flow flexible fuel line 
assemblies for twisted or damaged fuel lines or damaged shrouds, and 
replacement of

[[Page 45611]]

motive flow flexible fuel line assemblies with twisted or damaged fuel 
lines or damaged shrouds.
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this NPRM after determining that 
the unsafe condition described previously is likely to exist or develop 
in other products of the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in Transport Canada AD CF-2023-64 described previously, except for any 
differences identified as exceptions in the regulatory text of this 
proposed AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, the 
FAA proposes to incorporate Transport Canada AD CF-2023-64 by reference 
in the FAA final rule. This proposed AD would, therefore, require 
compliance with Transport Canada AD CF-2023-64 in its entirety through 
that incorporation, except for any differences identified as exceptions 
in the regulatory text of this proposed AD. Service information 
required by Transport Canada AD CF-2023-64 for compliance will be 
available at regulations.gov under Docket No. FAA-2024-1474 after the 
FAA final rule is published.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 93 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
7 work-hours x $85 per hour = $595...........................              $0               $0          $55,335
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary on-
condition actions that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need this on-condition action:

                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
                                                             Cost per
              Labor cost                   Parts cost        product
------------------------------------------------------------------------
1 work-hour x $85 per hour = $85......          $2,500           $2,585
------------------------------------------------------------------------

    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this proposed AD may be covered under warranty, thereby reducing the 
cost impact on affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:


[[Page 45612]]


Airbus Canada Limited Partnership (Type Certificate Previously Held 
by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.): 
Docket No. FAA-2024-1474; Project Identifier MCAI-2023-01014-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by July 8, 2024.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus Canada Limited Partnership (Type 
Certificate previously held by C Series Aircraft Limited Partnership 
(CSALP); Bombardier, Inc.) Model BD-500-1A10 and BD-500-1A11 
airplanes, certificated in any category, as identified in Transport 
Canada AD CF-2023-64, dated September 18, 2023 (Transport Canada AD 
CF-2023-64).

(d) Subject

    Air Transport Association (ATA) of America Code 28, Fuel.

(e) Unsafe Condition

    This AD was prompted by reports that the pylon-to-wing area 
motive flow flexible fuel line assemblies may have been installed 
incorrectly. The FAA is issuing this AD to ensure the motive flow 
flexible fuel line assemblies are installed correctly. The unsafe 
condition, if not addressed, could result in abrasion of the fuel 
line and a possible fuel leak; as a result, the electrical harness 
connectors in the wing area could be a potential ignition source and 
pose a risk of fire.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, Transport Canada AD CF-2023-64.

(h) Exception to Transport Canada AD CF-2023-64

    (1) Where Transport Canada AD CF-2023-64 refers to its effective 
date, this AD requires using the effective date of this AD.
    (2) Where Transport Canada AD CF-2023-64 refers to hours air 
time, this AD requires using flight hours.
    (3) Where the Corrective Actions paragraph of Transport Canada 
AD CF-2023-64 specifies to ``Inspect and, if necessary, replace the 
left and right motive flow fuel line assemblies,'' for this AD, 
replace that text with ``Inspect and, as applicable, replace the 
left and right motive flow flexible fuel line assemblies.''

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the manager of the 
International Validation Branch, mail it to the address identified 
in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or Transport Canada; or Airbus Canada 
Limited Partnership's Transport Canada Design Approval Organization 
(DAO). If approved by the DAO, the approval must include the DAO-
authorized signature.

(j) Additional Information

    For more information about this AD, contact Joseph Catanzaro, 
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 516-228-7366; email 
[email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Transport Canada AD CF-2023-64, dated September 18, 2023.
    (ii) [Reserved]
    (3) For Transport Canada AD CF-2023-64, contact Transport 
Canada, Transport Canada National Aircraft Certification, 159 
Cleopatra Drive, Nepean, Ontario K1A 0N5, Canada; telephone 888-663-
3639; email [email protected]. You may find this Transport 
Canada AD on the Transport Canada website tc.canada.ca/en/aviation.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th 
Street, Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195.
    (5) You may view this material at the National Archives and 
Records Administration (NARA). For information on the availability 
of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations, or email [email protected].

    Issued on May 16, 2024.
James D. Foltz,
Deputy Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2024-11163 Filed 5-22-24; 8:45 am]
BILLING CODE 4910-13-P