[Federal Register Volume 89, Number 89 (Tuesday, May 7, 2024)]
[Notices]
[Pages 38021-38025]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2024-09940]
-----------------------------------------------------------------------
DEPARTMENT OF COMMERCE
International Trade Administration
[A-301-806]
Aluminum Extrusions From Colombia: Preliminary Affirmative
Determination of Sales at Less Than Fair Value, Postponement of Final
Determination, and Extension of Provisional Measures
AGENCY: Enforcement and Compliance, International Trade Administration,
Department of Commerce.
SUMMARY: The U.S. Department of Commerce (Commerce) preliminarily
determines that Aluminum Extrusions from Colombia are being, or are
likely to be, sold in the United States at less than fair value (LTFV).
The period of investigation (POI) is October 1, 2022, through September
30, 2023. Interested parties are invited to comment on this preliminary
determination.
DATES: Applicable May 7, 2024.
FOR FURTHER INFORMATION CONTACT: Jose Rivera or Lingjun Wang, AD/CVD
Operations, Office VII, Enforcement and Compliance, International Trade
Administration, U.S. Department of Commerce, 1401 Constitution Avenue
NW, Washington, DC 20230; telephone: (202) 482-0842 or (202) 482-2316,
respectively.
SUPPLEMENTARY INFORMATION:
Background
This preliminary determination is made in accordance with section
733(b) of the Tariff Act of 1930, as amended (the Act). Commerce
published the notice of initiation of this investigation in the Federal
Register on October 31, 2023.\1\ On February 15, 2024, Commerce
postponed the preliminary determination of this investigation until May
1, 2024.\2\
---------------------------------------------------------------------------
\1\ See Aluminum Extrusions from the People's Republic of China,
Colombia, the Dominican Republic, Ecuador, India, Indonesia, Italy,
the Republic of Korea, Malaysia, Mexico, Taiwan, Thailand, the
Republic of Turkey, the United Arab Emirates, and the Socialist
Republic of Vietnam: Initiation of Less-Than-Fair-Value
Investigations, 88 FR 74421 (October 31, 2023) (Initiation Notice).
\2\ See Aluminum Extrusions from the People's Republic of China,
Colombia, the Dominican Republic, Ecuador, India, Indonesia, Italy,
the Republic of Korea, Malaysia, Mexico, Taiwan, Thailand, the
Republic of Turkey, the United Arab Emirates, and the Socialist
Republic of Vietnam: Postponement of Preliminary Determinations in
the Less-Than-Fair-Value Investigations, 89 FR 11814 (February 15,
2024).
---------------------------------------------------------------------------
For a complete description of the events that followed the
initiation of this investigation, see the Preliminary Decision
Memorandum.\3\ A list of topics included in the Preliminary Decision
Memorandum is included as Appendix II to this notice. The Preliminary
Decision Memorandum is a public document and is on file electronically
via Enforcement and Compliance's Antidumping and Countervailing Duty
Centralized Electronic Service System (ACCESS). ACCESS is available to
registered users at https://access.trade.gov. In addition, a complete
version of the Preliminary Decision Memorandum can be accessed directly
at https://access.trade.gov/public/FRNoticesListLayout.aspx.
---------------------------------------------------------------------------
\3\ See Memorandum, ``Decision Memorandum for the Preliminary
Affirmative Determination in the Less-Than-Fair-Value Investigation
of Aluminum Extrusions from Colombia,'' dated concurrently with, and
hereby adopted by, this notice (Preliminary Decision Memorandum).
---------------------------------------------------------------------------
Scope of the Investigation
The products covered by this investigation are aluminum extrusions
from Colombia. For a complete description of the scope of this
investigation, see Appendix I.
Scope Comments
In accordance with the preamble to Commerce's regulations,\4\ in
the Initiation Notice, Commerce set aside a period of time for parties
to raise issues regarding product coverage (i.e., scope).\5\ Certain
interested parties commented on the scope of the investigation as it
appeared in the Initiation Notice, as well as additional language
proposed by Commerce. For a summary of the product coverage comments
and rebuttal responses submitted to the record for this preliminary
determination, and accompanying discussion and analysis of all comments
timely received, see the Preliminary Scope Decision Memorandum II.\6\
Commerce is preliminarily modifying the scope language as it appeared
in the Initiation Notice. See the revised scope in Appendix I to this
notice.
---------------------------------------------------------------------------
\4\ See Antidumping Duties; Countervailing Duties, Final Rule,
62 FR 27296, 27323 (May 19, 1997).
\5\ See Initiation Notice.
\6\ See Memorandum, ``Preliminary Scope Decision Memorandum
II,'' dated concurrently with this memorandum.
---------------------------------------------------------------------------
Methodology
Commerce is conducting this investigation in accordance with
section 731 of the Act. Commerce calculated export prices in accordance
with section 772(a) of the Act. Constructed export prices have been
calculated in accordance with section 772(b) of the Act. Normal value
is calculated in accordance with section 773 of the Act. For a full
description of the methodology underlying the preliminary
determination, see the Preliminary Decision Memorandum.
All-Others Rate
Sections 733(d)(1)(ii) and 735(c)(5)(A) of the Act provide that in
a preliminary determination Commerce shall determine an estimated all-
others rate for all exporters and producers not individually examined.
This rate shall be an amount equal to the weighted average of the
estimated weighted-average dumping margins established for exporters
and producers individually investigated, excluding any zero and de
minimis margins, and any margins determined entirely under section 776
of the Act.
In this investigation, Commerce calculated estimated weighted-
average dumping margins for Aluminio Nacional S.A. (Alumina) \7\ and
Tecnoglass, S.A.S. (Tecnoglass) that are not zero, de minimis, or based
entirely on facts otherwise available. Commerce calculated the all-
others rate using a weighted average of the estimated weighted-average
dumping margins calculated for the examined respondents using each
company's publicly-ranged values for the merchandise under
consideration.\8\
---------------------------------------------------------------------------
\7\ Aluminio Nacional S.A. is currently operating under the
legal name Aluminio Nacional S.A. en reorganizacion, as it is
undergoing a debt reorganization process.
\8\ With two respondents under examination, Commerce normally
calculates: (A) a weighted-average of the estimated weighted-average
dumping margins calculated for the examined respondents; (B) a
simple average of the estimated weighted-average dumping margins
calculated for the examined respondents; and (C) a weighted-average
of the estimated weighted-average dumping margins calculated for the
examined respondents using each company's publicly-ranged U.S. sales
values for the merchandise under consideration. Commerce then
compares (B) and (C) to (A) and selects the rate closest to (A) as
the most appropriate rate for all other producers and exporters.
See, e.g., Ball Bearings and Parts Thereof from France, Germany,
Italy, Japan, and the United Kingdom: Final Results of Antidumping
Duty Administrative Reviews, Final Results of Changed-Circumstances
Review, and Revocation of an Order in Part, 75 FR 53661, 53662
(September 1, 2010), and accompanying Issues and Decision Memorandum
at Comment 1. As complete publicly ranged sales data were available,
Commerce based the all-others rate on the publicly ranged sales data
of the mandatory respondents. For a complete analysis of the data,
see Memorandum, ``Preliminary Calculation of the All-Others Rate,''
dated concurrently with this notice.
---------------------------------------------------------------------------
[[Page 38022]]
Preliminary Determination
Commerce preliminarily determines that the following estimated
weighted-average dumping margins exist:
---------------------------------------------------------------------------
\9\ As noted above, Aluminio Nacional S.A. is currently
operating under the legal name Aluminio Nacional S.A. en
reorganizacion.
\10\ For purposes of this preliminarily determination, we are
collapsing Tecnoglass, S.A.S., C.I. Energ[iacute]a Solar S.A.S. E.S.
Windows, and C.I. E.S. Metals S.A.S. and treating them as a single
entity. See Preliminary Decision Memorandum.
------------------------------------------------------------------------
Estimated
weighted-
Exporter/producer average
dumping margin
(percent)
------------------------------------------------------------------------
Aluminio Nacional S.A.\9\............................... 34.47
Tecnoglass, S.A.S.; C.I. Energia Solar S.A.S. E.S. 8.85
Windows; and C.I. E.S. Metals S.A.S.\10\...............
All Others.............................................. 12.42
------------------------------------------------------------------------
Suspension of Liquidation
In accordance with section 733(d)(2) of the Act, Commerce will
direct U.S. Customs and Border Protection (CBP) to suspend liquidation
of entries of subject merchandise, as described in Appendix I, entered,
or withdrawn from warehouse, for consumption on or after the date of
publication of this notice in the Federal Register. Further, pursuant
to section 733(d)(1)(B) of the Act and 19 CFR 351.205(d), Commerce will
instruct CBP to require a cash deposit equal to the estimated weighted-
average dumping margin or the estimated all-others rate, as follows:
(1) the cash deposit rate for the respondents listed above will be
equal to the company-specific estimated weighted-average dumping
margins determined in this preliminary determination; (2) if the
exporter is not a respondent identified above, but the producer is,
then the cash deposit rate will be equal to the company-specific
estimated weighted-average dumping margin established for that producer
of the subject merchandise; and (3) the cash deposit rate for all other
producers and exporters will be equal to the all-others estimated
weighted-average dumping margin. These suspension of liquidation
instructions will remain in effect until further notice.
Disclosure
Commerce intends to disclose its calculations and analysis
performed to interested parties in this preliminary determination
within five days of any public announcement or, if there is no public
announcement, within five days of the date of publication of this
notice in accordance with 19 CFR 351.224(b).
Verification
As provided in section 782(i)(1) of the Act, Commerce intends to
verify the information relied upon in making its final determination.
Public Comment
For scope-related comments, please refer to the Preliminary Scope
Decision Memorandum II for the timeline of scope comments. After the
submission of comments, Commerce will set a schedule for the submission
of case and rebuttal briefs limited to scope issues.
Case briefs or other written comments may be submitted to the
Assistant Secretary for Enforcement and Compliance no later than seven
days after the date on which the last verification report is issued in
this investigation.\11\ Rebuttal briefs, limited to issues raised in
the case briefs, may be filed not later than five days after the date
for filing case briefs.\12\ Interested parties who submit case briefs
or rebuttal briefs in this proceeding must submit: (1) a table of
contents listing each issue; and (2) a table of authorities.\13\
---------------------------------------------------------------------------
\11\ See 19 CFR 351.309(c)(1)(i); see also 19 CFR 351.303 (for
general filing requirements).
\12\ See 19 CFR 351.309(d); see also Administrative Protective
Order, Service, and Other Procedures in Antidumping and
Countervailing Duty Proceedings, 88 FR 67069, 67077 (September 29,
2023) (APO and Service Final Rule).
\13\ See 19 351.309(c)(2) and (d)(2).
---------------------------------------------------------------------------
As provided under 19 CFR 351.309(c)(2) and (d)(2), in prior
proceedings we have encouraged interested parties to provide an
executive summary of their brief that should be limited to five pages
total, including footnotes. In this investigation, we instead request
that interested parties provide at the beginning of their briefs a
public, executive summary for each issue raised in their briefs.\14\
Further, we request that interested parties limit their executive
summary of each issue to no more than 450 words, not including
citations. We intend to use the public, executive summaries as the
basis of the comment summaries included in the issues and decision
memorandum that will accompany the final determination in this
investigation. We request that interested parties include footnotes for
relevant citations in the public, executive summary of each issue. Note
that Commerce has amended certain of its requirements pertaining to the
service of documents in 19 CFR 351.303(f).\15\
---------------------------------------------------------------------------
\14\ We use the term ``issue'' here to describe an argument that
Commerce would normally address in a comment of the Issues and
Decision Memorandum.
\15\ See APO and Service Final Rule.
---------------------------------------------------------------------------
Pursuant to 19 CFR 351.310(c), interested parties who wish to
request a hearing, limited to issues raised in the case and rebuttal
briefs, must submit a written request to the Assistant Secretary for
Enforcement and Compliance, U.S. Department of Commerce, within 30 days
after the date of publication of this notice. Requests should contain
the party's name, address, and telephone number, the number of
participants, whether any participant is a foreign national, and a list
of the issues to be discussed. If a request for a hearing is made,
Commerce intends to hold the hearing at a time and date to be
determined. Parties should confirm by telephone the date, time, and
location of the hearing two days before the scheduled date.
[[Page 38023]]
Postponement of Final Determination and Extension of Provisional
Measures
Section 735(a)(2) of the Act provides that a final determination
may be postponed until not later than 135 days after the date of the
publication of the preliminary determination if, in the event of an
affirmative preliminary determination, a request for such postponement
is made by exporters who account for a significant proportion of
exports of the subject merchandise, or in the event of a negative
preliminary determination, a request for such postponement is made by
the petitioner. Section 351.210(e)(2) of Commerce's regulations
requires that a request by exporters for postponement of the final
determination be accompanied by a request for extension of provisional
measures from a four-month period to a period not more than six months
in duration.
Between April 17 and 24, 2024, pursuant to 19 CFR 351.210(e), the
petitioners,\16\ Alumina, and Tecnoglass each requested that Commerce
postpone the final determination and that provisional measures be
extended to a period not to exceed six months.\17\ In accordance with
section 735(a)(2)(A) of the Act and 19 CFR 351.210(b)(2)(ii), because:
(1) the preliminary determination is affirmative; (2) the requesting
exporters account for a significant proportion of exports of the
subject merchandise; and (3) no compelling reasons for denial exist,
Commerce is postponing the final determination and extending the
provisional measures from a four-month period to a period not greater
than six months. Accordingly, Commerce will make its final
determination no later than 135 days after the date of publication of
this preliminary determination.
---------------------------------------------------------------------------
\16\ The petitioners are U.S. Aluminum Extruders Coalition and
the United Steel, Paper and Forestry, Rubber, Manufacturing, Energy,
Allied Industrial and Service Workers International Union.
\17\ See Petitioners' Letter, ``Request for Postponement of
Final Determinations,'' dated April 17, 2024; see also Alumina's
Letter, ``Request for Postponement of Final Determinations,'' dated
April 18, 2024, and Tecnoglass' Letter, ``Tecnoglass' Request to
Postpone Final Determination,'' dated April 24, 2024.
---------------------------------------------------------------------------
U.S. International Trade Commission Notification
In accordance with section 733(f) of the Act, Commerce will notify
the U.S. International Trade Commission (ITC) of its preliminary
determination. If the final determination is affirmative, the ITC will
determine before the later of 120 days after the date of this
preliminary determination or 45 days after the final determination
whether these imports are materially injuring, or threaten material
injury to, the U.S. industry.
Notification to Interested Parties
This determination is issued and published in accordance with
sections 733(f) and 777(i)(1) of the Act and 19 CFR 351.205(c).
Dated: May 1, 2024.
Ryan Majerus,
Deputy Assistant Secretary for Policy and Negotiations, performing the
non-exclusive functions and duties of the Assistant Secretary for
Enforcement and Compliance.
Appendix I
Scope of the Investigation
The merchandise subject to this investigation are aluminum
extrusions, regardless of form, finishing, or fabrication, whether
assembled with other parts or unassembled, whether coated, painted,
anodized, or thermally improved. Aluminum extrusions are shapes and
forms, produced by an extrusion process, made from aluminum alloys
having metallic elements corresponding to the alloy series
designations published by the Aluminum Association commencing with
the numbers 1, 3, and 6 (or proprietary equivalents or other
certifying body equivalents). Specifically, subject aluminum
extrusions made from an aluminum alloy with an Aluminum Association
series designation commencing with the number 1 contain not less
than 99 percent aluminum by weight. Subject aluminum extrusions made
from an aluminum alloy with an Aluminum Association series
designation commencing with the number 3 contain manganese as the
major alloying element, with manganese accounting for not more than
3.0 percent of total materials by weight. Subject aluminum
extrusions made from an aluminum alloy with an Aluminum Association
series designation commencing with the number 6 contain magnesium
and silicon as the major alloying elements, with magnesium
accounting for at least 0.1 percent but not more than 2.0 percent of
total materials by weight, and silicon accounting for at least 0.1
percent but not more than 3.0 percent of total materials by weight.
The scope also includes merchandise made from an aluminum alloy with
an Aluminum Association series designation commencing with the
number 5 (or proprietary equivalents or other certifying body
equivalents) that have a magnesium content accounting for up to but
not more than 2.0 percent of total materials by weight.
The country of origin of the aluminum extrusion is determined by
where the metal is extruded (i.e., pressed through a die).
Aluminum extrusions are produced and imported in a wide variety
of shapes and forms, including, but not limited to, hollow profiles,
other solid profiles, pipes, tubes, bars, and rods. Aluminum
extrusions that are drawn subsequent to extrusion (drawn aluminum)
are also included in the scope.
Subject aluminum extrusions are produced and imported with a
variety of coatings and surface treatments, and types of
fabrication. The types of coatings and treatments applied to
aluminum extrusions include, but are not limited to, extrusions that
are mill finished (i.e., without any coating or further finishing),
brushed, buffed, polished, anodized (including bright dip), liquid
painted, electroplated, chromate converted, powder coated,
sublimated, wrapped, and/or bead blasted. Subject aluminum
extrusions may also be fabricated, i.e., prepared for assembly, or
thermally improved. Such operations would include, but are not
limited to, extrusions that are cut-to-length, machined, drilled,
punched, notched, bent, stretched, stretch-formed, hydroformed,
knurled, wedged, mitered, chamfered, threaded, spun, etched, and
engraved. Performing such operations in third countries does not
otherwise remove the merchandise from the scope of the
investigation.
The types of products that meet the definition of subject
merchandise include but are not limited to, the aluminum extrusion
portions of vehicle roof rails and sun/moon roof framing, solar
panel racking rails and framing, tradeshow display fixtures and
framing, parts for tents or clear span structures, fence posts,
drapery rails or rods, electrical conduits, door thresholds,
flooring trim, electric vehicle battery trays, heat sinks, signage
or advertising poles, telescoping poles, or cleaning system
components.
Aluminum extrusions may be heat sinks, which are fabricated
aluminum extrusions that dissipate heat away from a heat source and
may serve other functions, such as structural functions. Heat sinks
come in a variety of sizes and shapes, including but not limited to
a flat electronic heat sink, which is a solid aluminum extrusion
with at least one flat side used to mount electronic or mechanical
devices; a heat sink that is a housing for electronic controls or
motors; lighting heat sinks, which dissipate heat away from LED
devices; and process and exchange heat sinks, which are tube
extrusions with fins or plates used to hold radiator tubing. Heat
sinks are included in the scope, regardless of whether the design
and production of the heat sinks are organized around meeting
specified thermal performance requirements and regardless of whether
they have been tested to comply with such requirements. For purposes
of the investigation on aluminum extrusions from the People's
Republic of China, only heat sinks designed and produced around
meeting specified thermal performance requirements and tested to
comply with such requirements are included in the scope. Excluded
from the scope of the investigation are large, multi-finned extruded
aluminum heat sinks designed to dissipate heat, meeting the
following criteria: (1) an aspect ratio (defined as the ratio of the
area of a void in an extrusion to the size of the smallest gap
opening at the entrance of that void and calculated by dividing the
void area by the square of the gap opening) greater than 15 to 1; or
(2) the circumscribing circle diameter (defined as the diameter of
the smallest circle that will entirely enclose the extrusion's
cross-sectional profile) rounded up to the next half inch, exceeds
10 inches, and the weight-per-foot (defined as the theoretical
[[Page 38024]]
weight of the profile as extruded prior to any machining that may
remove material and calculated by multiplying the area of the
profile in square inches by 1.2) exceeds 3.50 pounds per foot.
Merchandise that is comprised solely of aluminum extrusions or
aluminum extrusions and fasteners, whether assembled at the time of
importation or unassembled, is covered by the scope in its entirety.
The scope also includes aluminum extrusions contained in
merchandise that is a part or subassembly of a larger whole, whether
or not the merchandise also contains a component other than aluminum
extrusions that is beyond a fastener. Such merchandise may be either
assembled or unassembled at the time of importation. A ``part or
subassembly'' is defined as a unit designed to be attached to, or
incorporated with, one or more other units or components into a
larger completed product. Only the aluminum extrusion portion of the
merchandise described in this paragraph, whether assembled or
unassembled, is subject merchandise included in the scope and
subject to duties. Examples of merchandise that is a part or
subassembly of a larger whole include, but are not limited to,
window parts or subassemblies; door unit parts or subassemblies;
shower and bath parts or subassemblies; solar panel mounting
systems; fenestration system parts or subassemblies, such as curtain
wall and window wall units and parts or subassemblies of
storefronts; furniture parts or subassemblies; appliance parts or
subassemblies, such as fin evaporator coils and systems for
refrigerators; railing or deck system parts or subassemblies; fence
system parts or subassemblies; motor vehicle parts or subassemblies,
such as bumpers for motor vehicles; trailer parts or subassemblies,
such as side walls, flooring, and roofings; electric vehicle
charging station parts or subassemblies; or signage or advertising
system parts or subassemblies. Parts or subassemblies described by
this paragraph that are subject to duties in their entirety pursuant
to existing antidumping and countervailing duty orders (defined as
those antidumping and countervailing duty orders that are in effect
as of the date of publication of the order resulting from this
investigation) are excluded from the scope of this investigation.
Any part or subassembly that otherwise meets the requirements of
this scope and that is not covered by other antidumping and/or
countervailing duty orders remains subject to the scope of the
investigation.
The scope excludes aluminum extrusions contained in fully and
permanently assembled merchandise, if the assembled merchandise is
not a part or subassembly of a larger whole. To be excluded under
this paragraph, the assembled merchandise must also contain a
component other than aluminum extrusions, beyond fasteners. In
addition, to be excluded under this paragraph, the assembled
merchandise must be ready for use as imported, without undergoing
after importation any processing, fabrication, finishing, or
assembly or the addition of parts or material (with the exception of
consumable parts or material or interchangeable media or tooling).
The scope also excludes aluminum extrusions contained in
unassembled merchandise if the unassembled merchandise is not a part
or subassembly of a larger whole. To be excluded under this
paragraph, the unassembled merchandise must also contain a component
other than aluminum extrusions, beyond fasteners. In addition, to be
excluded under this paragraph, the unassembled merchandise must be a
packaged combination of parts that is ready to be assembled as
imported, without undergoing after importation any processing,
fabrication, or finishing or the addition of parts or material (with
the exception of consumable parts or material or interchangeable
media or tooling). To be excluded under this paragraph, the
unassembled merchandise must be sold and enter as a discrete kit on
one Customs entry form.
Examples of such excluded assembled and unassembled merchandise
include windows with glass, door units with door panel and glass,
motor vehicles, trailers, furniture, appliances, and solar panels
and solar modules.
The scope also excludes merchandise containing multiple
subassemblies of a larger whole with non-extruded aluminum
components beyond fasteners. A subassembly that meets the definition
of subject merchandise, including any product expressly identified
as subject merchandise in this scope, can only be excluded if it is
fully and permanently assembled with at least one other different
subassembly, and where (1) at least one of the subassemblies, if
entered individually, would not itself be subject to the scope; (2)
the aluminum extrusions within the merchandise collectively account
for 50 percent or less of the actual weight of the combined multiple
subassemblies (without including any non-extruded aluminum fasteners
in the calculations); and (3) the aluminum extrusions within the
merchandise collectively account for 50 percent or less of the
number of pieces of the combined multiple subassemblies (without
including any non-extruded aluminum fasteners in the calculations).
The scope also includes aluminum extrusions that have been
further processed in a third country, including, but not limited to,
the finishing and fabrication processes described above, assembly,
whether with other aluminum extrusion components or with non-
aluminum extrusion components, or any other processing that would
not otherwise remove the merchandise from the scope if performed in
the country of manufacture of the in-scope product. Third country
processing; finishing; and/or fabrication, including those processes
described in the scope, does not alter the country of origin of the
subject aluminum extrusions.
The following aluminum extrusion products are excluded: aluminum
extrusions made from an aluminum alloy with an Aluminum Association
series designations commencing with the number 2 (or proprietary
equivalents or other certifying body equivalents) and containing in
excess of 1.5 percent copper by weight; aluminum extrusions made
from an aluminum alloy with an Aluminum Association series
designation commencing with the number 5 (or proprietary equivalents
or other certifying body equivalents) and containing in excess of
2.0 percent magnesium by weight; and aluminum extrusions made from
an aluminum alloy with an Aluminum Association series designation
commencing with the number 7 (or proprietary equivalents or other
certifying body equivalents) and containing in excess of 2.0 percent
zinc by weight.
The scope also excludes aluminum alloy sheet or plates produced
by means other than the extrusion process, such as aluminum products
produced by a method of continuous casting or rolling. Cast aluminum
products are also excluded. The scope also excludes unwrought
aluminum in any form.
The scope also excludes collapsible tubular containers composed
of metallic elements corresponding to alloy code 1080A as designated
by the Aluminum Association (not including proprietary equivalents
or other certifying body equivalents) where the tubular container
(excluding the nozzle) meets each of the following dimensional
characteristics: (1) length of 37 millimeters (mm) or 62 mm; (2)
outer diameter of 11.0 mm or 12.7 mm; and (3) wall thickness not
exceeding 0.13 mm.
Also excluded from the scope are extruded drawn solid profiles
made from an aluminum alloy with the Aluminum Association series
designation commencing with the number 1, 3, or 6 (or proprietary
equivalents or other certifying body equivalents), including
variants on individual alloying elements not to circumvent the other
Aluminum Association series designations, which meet each of the
following characteristics: (1) solid cross sectional area greater
than 62.4 mm\2\ and less than 906 mm\2\, (2) minimum electrical
conductivity of 58% of the international annealed copper standard
(IACS) or maximum resistivity of 2.97 [mu][Omega]/cm, (3) a
uniformly applied nonelectrically conductive temperature-resistant
coating co-extruded over characteristic (1) of either polyamide,
cross-linked polyethylene, or silicone rubber material which meets
the following standards: (a) Vicat A temperature threshold of >140
degrees Celsius, (b) flammability requirements of UL 94V-0, and (c)
a minimum coating thickness of 0.10 mm and maximum coating thickness
of 2.0 mm, with a maximum thickness tolerance of +/-0.20 mm, (4)
characteristic 3 may or may not be encapsulated with a ``Precision
Drawn Tubing,'' wall thicknesses less than 1.2 mm, which is
mechanically fixed in place, and (5) packaged in straight lengths,
bent or formed and/or attached to hardware.
Also excluded from the scope are extruded tubing and drawn over
a ID plug and through a OD die made from an aluminum alloy with the
Aluminum Association series designation commencing with the number
3, 5, or 6 (or proprietary equivalents or other certifying body
equivalents), including variants on individual alloying elements not
to circumvent the other Aluminum Association series designations,
which meet each of the following characteristics: (1) an outside
mean diameter no greater than 30 mm with a
[[Page 38025]]
tolerance less than or equal to +/-0.10 mm, (2) uniform wall
thickness no greater than 2.7 mm with wall tolerances less than or
equal to +/-0.1 mm, (3) may be coated with materials, including
zinc, such that the coating material weight is no less than 3 g/m\2\
and no greater than 30 g/m\2\, and (4) packaged in continuous coils,
straight lengths, bent or formed.
The scope also excludes fully and permanently assembled glass
refrigerator shelves with decorative aluminum trim meeting the
following characteristics: (1) aluminum trim meeting Aluminum
Association series 6063-T5 designation that is anodized; (2)
aluminum trim length of not more than 800 mm, and (3) aluminum trim
width of not more than 40 mm. Such fully and permanently assembled
glass refrigerator shelves include other components in addition to
the aluminum trim, including, but not limited to, glass, steel, and
plastic. Only fully and permanently assembled glass refrigerator
shelves that require no further processing, fabrication, finishing,
assembly, or the addition of any parts or material are excluded.
Imports of glass refrigerator shelves are classified under HTSUS
8418.99.8050, which is being included for convenience.
Also excluded from the scope of this investigation is certain
rectangular wire, imported in bulk rolls or precut strips and
produced from continuously cast rolled aluminum wire rod, which is
subsequently extruded to dimension to form rectangular wire with or
without rounded edges. The product is made from aluminum alloy grade
1070 or 1370 (not including proprietary equivalents or other
certifying body equivalents), with no recycled metal content
allowed. The dimensions of the wire are 2.95 mm to 6.05 mm in width,
and 0.65 mm to 1.25 mm in thickness. Imports of rectangular wire are
provided for under Harmonized Tariff Schedule of the United States
(HTSUS) subheadings 7605.19.0000, 7604.10.5000, or 7616.99.5190.
Also excluded from the scope of these antidumping and
countervailing duty investigations on aluminum extrusions from the
People's Republic of China are all products covered by the scope of
the antidumping and countervailing duty orders on Aluminum
Extrusions from the People's Republic of China. See Aluminum
Extrusions from the People's Republic of China: Antidumping Duty
Order, 76 FR 30650 (May 26, 2011); and Aluminum Extrusions from the
People's Republic of China: Countervailing Duty Order, 76 FR 30653
(May 26, 2011) (collectively, Aluminum Extrusions from the People's
Republic of China). Solely for the investigations on aluminum
extrusions from the People's Republic of China, the following is an
exhaustive list of products where the aluminum extrusion portions
thereof meet the definition of subject merchandise. The language
contained in the rest of the scope applies to this exhaustive list
of products. Merchandise that is not included in the following list
that meets the definition of subject merchandise in the 2011
antidumping and countervailing duty orders on Aluminum Extrusions
from the People's Republic of China remains subject to the earlier
orders. No other section of this scope language that provides
examples of subject merchandise is exhaustive.
The aluminum extrusion portions of the following products are
included in the scope of the investigations on aluminum extrusions
from the People's Republic of China, whether assembled or
unassembled: heat sinks as described above; cleaning system
components like mops and poles; banner stands/back walls; fabric
wall systems; drapery rails; side mount valve controls; water heater
anodes; solar panel mounting systems; automotive heating and cooling
system components; assembled motor cases with stators; louver
assemblies; event d[eacute]cor; window wall units and parts; trade
booths; micro channel heat exchangers; telescoping poles, pole
handles, and pole attachments; flagpoles; wind sign frames; foreline
hose assembly; electronics enclosures; parts and subassemblies for
storefronts, including portal sets; light poles; air duct registers;
outdoor sporting goods parts and subassemblies; glass refrigerator
shelves; aluminum ramps; handicap ramp system parts and
subassemblies; frames and parts for tents and clear span structures;
parts and subassemblies for screen enclosures, patios, and sunrooms;
parts and subassemblies for walkways and walkway covers; aluminum
extrusions for Light Emitting Diode (LED) lights; parts and
subassemblies for screen, storm, and patio doors; pontoon boat parts
and subassemblies, including rub rails, flooring, decking, transom
structures, canopy systems, seating; boat hulls, framing, ladders,
and transom structures; parts and subassemblies for docks, piers,
boat lifts and mounting; recreational and boat trailer parts and
subassemblies, including subframes, crossmembers, and gates; solar
tracker assemblies with gears; garage door framing systems; door
threshold and sill assemblies; highway and bridge signs; bridge,
street, and highway rails; scaffolding, including planks and struts;
railing and support systems; parts and subassemblies for exercise
equipment; weatherstripping; door bottom and sweeps; door seals;
floor transitions and trims; parts and subassemblies for modular
walls and office furniture; truck trailer parts and subassemblies;
boat cover poles, outrigger poles, and rod holders; bleachers and
benches; parts and subassemblies for elevators, lifts, and
dumbwaiters; parts and subassemblies for mirror and framing systems;
window treatments; parts and subassemblies for air foils and fans;
bus and Recreational Vehicle (RV) window frames; sliding door rails;
dock ladders; parts and subassemblies for RV frames and trailers;
awning, canopy, and sunshade structures and their parts and
subassemblies; marine motor mounts; linear lighting housings; and
cluster mailbox systems.
Imports of the subject merchandise are primarily provided for
under the following categories of the HTSUS: 7604.10.1000;
7604.10.3000; 7604.10.5000; 7604.21.0010; 7604.21.0090;
7604.29.1010; 7604.29.1090; 7604.29.3060; 7604.29.3090;
7604.29.5050; 7604.29.5090; 7608.10.0030; 7608.10.0090;
7608.20.0030; 7608.20.0090; 7609.00.0000; 7610.10.0010;
7610.10.0020; 7610.10.0030; 7610.90.0040; and 7610.90.0080.
Imports of the subject merchandise, including subject
merchandise entered as parts of other products, may also be
classifiable under the following additional HTSUS categories, as
well as other HTSUS categories: 6603.90.8100; 7606.12.3091;
7606.12.3096; 7615.10.2015; 7615.10.2025; 7615.10.3015;
7615.10.3025; 7615.10.5020; 7615.10.5040; 7615.10.7125;
7615.10.7130; 7615.10.7155; 7615.10.7180; 7615.10.9100;
7615.20.0000; 7616.10.9090; 7616.99.1000; 7616.99.5130;
7616.99.5140; 7616.99.5190; 8302.10.3000; 8302.10.6030;
8302.10.6060; 8302.10.6090; 8302.20.0000; 8302.30.3010;
8302.30.3060; 8302.41.3000; 8302.41.6015; 8302.41.6045;
8302.41.6050; 8302.41.6080; 8302.42.3010; 8302.42.3015;
8302.42.3065; 8302.49.6035; 8302.49.6045; 8302.49.6055;
8302.49.6085; 8302.50.0000; 8302.60.3000; 8302.60.9000;
8305.10.0050; 8306.30.0000; 8414.59.6590; 8415.90.8045;
8418.99.8005; 8418.99.8050; 8418.99.8060; 8419.50.5000;
8419.90.1000; 8422.90.0640; 8424.90.9080; 8473.30.2000;
8473.30.5100; 8479.89.9599; 8479.90.8500; 8479.90.9596;
8481.90.9060; 8481.90.9085; 8486.90.0000; 8487.90.0080;
8503.00.9520; 8508.70.0000; 8513.90.2000; 8515.90.2000;
8516.90.5000; 8516.90.8050; 8517.71.0000; 8517.79.0000;
8529.90.7300; 8529.90.9760; 8536.90.8585; 8538.10.0000;
8541.90.0000; 8543.90.8885; 8547.90.0020; 8547.90.0030;
8547.90.0040; 8708.10.3050; 8708.29.5160; 8708.80.6590;
8708.99.6890; 8807.30.0060; 9031.90.9195; 9401.99.9081;
9403.99.1040; 9403.99.9010; 9403.99.9015; 9403.99.9020;
9403.99.9040; 9403.99.9045; 9405.99.4020; 9506.11.4080;
9506.51.4000; 9506.51.6000; 9506.59.4040; 9506.70.2090;
9506.91.0010; 9506.91.0020; 9506.91.0030; 9506.99.0510;
9506.99.0520; 9506.99.0530; 9506.99.1500; 9506.99.2000;
9506.99.2580; 9506.99.2800; 9506.99.5500; 9506.99.6080;
9507.30.2000; 9507.30.4000; 9507.30.6000; 9507.30.8000;
9507.90.6000; and 9603.90.8050.
While HTSUS subheadings are provided for convenience and customs
purposes, the written description of the scope is dispositive.
Appendix II
List of Topics Discussed in the Preliminary Decision Memorandum
I. Summary
II. Background
III. Period of Investigation
IV. Affiliation and Single Entity Treatment
V. Discussion of the Methodology
VI. Currency Conversion
VII. Recommendation
[FR Doc. 2024-09940 Filed 5-6-24; 8:45 am]
BILLING CODE 3510-DS-P