[Federal Register Volume 89, Number 89 (Tuesday, May 7, 2024)]
[Notices]
[Pages 38057-38063]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2024-09937]
-----------------------------------------------------------------------
DEPARTMENT OF COMMERCE
International Trade Administration
[A-557-826]
Aluminum Extrusions From Malaysia: Preliminary Affirmative
Determination of Sales at Less Than Fair Value, Postponement of Final
Determination, and Extension of Provisional Measures
AGENCY: Enforcement and Compliance, International Trade Administration,
Department of Commerce.
SUMMARY: The U.S. Department of Commerce (Commerce) preliminarily
determines that aluminum extrusions from Malaysia are being, or are
likely to be, sold in the United States at less than fair value (LTFV).
The period of investigation (POI) is October 1, 2022, through September
30, 2023. Interested parties are invited to comment on this preliminary
determination.
DATES: Applicable May 7, 2024.
FOR FURTHER INFORMATION CONTACT: Paola Aleman Ordaz or Benjamin Blythe,
AD/CVD Operations, Office IV, Enforcement and Compliance, International
Trade Administration, U.S. Department of Commerce, 1401 Constitution
Avenue NW, Washington, DC 20230; telephone: (202) 482-4031 or (202)
482-3457, respectively.
SUPPLEMENTARY INFORMATION:
Background
This preliminary determination is made in accordance with section
733(b) of the Tariff Act of 1930, as amended (the Act). Commerce
published the notice of initiation of this investigation on October 31,
2023.\1\ On February 15, 2024, Commerce postponed the
[[Page 38058]]
preliminary determination in this investigation until May 1, 2024.\2\
---------------------------------------------------------------------------
\1\ See Aluminum Extrusions from the People's Republic of China,
Colombia, the Dominican Republic, Ecuador, India, Indonesia, Italy,
the Republic of Korea, Malaysia, Mexico, Taiwan, Thailand, the
Republic of Turkey, the United Arab Emirates, and the Socialist
Republic of Vietnam: Initiation of Less-Than-Fair-Value
Investigations, 88 FR 74421 (October 31, 2023) (Initiation Notice).
\2\ See Aluminum Extrusions from the People's Republic of China,
Colombia, Ecuador, India, Indonesia, Italy, the Republic of Korea,
Malaysia, Mexico, Taiwan, Thailand, the Republic of Turkey, the
United Arab Emirates, and the Socialist Republic of Vietnam:
Postponement of Preliminary Determinations in the Less-Than-Fair-
Value Investigations, 89 FR 11814 (February 15, 2024).
---------------------------------------------------------------------------
For a complete description of the events that followed the
initiation of this investigation, see the Preliminary Decision
Memorandum.\3\ A list of topics included in the Preliminary Decision
Memorandum is included as Appendix II to this notice. The Preliminary
Decision Memorandum is a public document and is on file electronically
via Enforcement and Compliance's Antidumping and Countervailing Duty
Centralized Electronic Service System (ACCESS). ACCESS is available to
registered users at https://access.trade.gov. In addition, a complete
version of the Preliminary Decision Memorandum can be accessed directly
at https://access.trade.gov/public/FRNoticesListLayout.aspx.
---------------------------------------------------------------------------
\3\ See Memorandum, ``Decision Memorandum for the Preliminary
Affirmative Determination in the Less-Than-Fair-Value Investigation
of Aluminum Extrusions from Malaysia,'' dated concurrently with, and
hereby adopted by, this notice (Preliminary Decision Memorandum).
---------------------------------------------------------------------------
Scope of the Investigation
The products covered by this investigation are aluminum extrusions
from Malaysia. For a complete description of the scope of this
investigation, see Appendix I.
Scope Comments
In accordance with the preamble to Commerce's regulations,\4\ in
the Initiation Notice, Commerce set aside a period of time for parties
to raise issues regarding product coverage (i.e., scope).\5\ Certain
interested parties commented on the scope of the investigation as it
appeared in the Initiation Notice, as well as additional language
proposed by Commerce. For a summary of the product coverage comments
and rebuttal responses submitted to the record for this preliminary
determination, and accompanying discussion and analysis of all comments
timely received, see the Preliminary Scope Decision Memo II.\6\
Commerce is preliminarily modifying the scope language as it appeared
in the Initiation Notice. See the revised scope in Appendix I to this
notice.
---------------------------------------------------------------------------
\4\ See Antidumping Duties; Countervailing Duties, Final Rule,
62 FR 27296, 27323 (May 19, 1997).
\5\ See Initiation Notice.
\6\ See Memorandum, ``Antidumping Duty Investigations and
Countervailing Duty Investigations of Aluminum Extrusions from
People's Republic of China, Colombia, Ecuador, India, Indonesia,
Italy, the Republic of Korea, Malaysia, Mexico, Taiwan, Thailand,
the Republic of Turkey, the United Arab Emirates, and the Socialist
Republic of Vietnam: Preliminary Scope Decision Memorandum II,''
dated concurrently with this notice (Preliminary Scope Decision Memo
II).
---------------------------------------------------------------------------
Methodology
Commerce is conducting this investigation in accordance with
section 731 of the Act. Commerce calculated export price in accordance
with sections 772(a) of the Act. Commerce calculated normal value in
accordance with section 773 of the Act. Furthermore, pursuant to
sections 776(a) and (b) of the Act, Commerce has preliminarily relied
upon facts otherwise available, with adverse inferences, for EL
Aluminium Billet (M) Sdn Bhd, Kosan Aluminum Extrusion SDN. BHD, and
Winstar Group. For a full description of the methodology underlying the
preliminary determination, see the Preliminary Decision Memorandum.
All-Others Rate
Sections 733(d)(1)(A)(ii) and 735(c)(5)(A) of the Act provide that,
in the preliminary determination, Commerce shall determine an estimated
all-others rate for all other exporters and producers not individually
examined. This rate shall be an amount equal to the weighted average of
the estimated weighted-average dumping margins established for
exporters and producers individually examined, excluding any rates that
are zero, de minimis, or determined entirely under section 776 of the
Act.
Pursuant to section 735(c)(5)(B) of the Act, if the estimated
weighted-average dumping margins established for all exporters and
producers individually examined are zero, de minimis, or determined
based entirely on facts otherwise available, Commerce may use any
reasonable method to establish the estimated weighted-average dumping
margin for all other producers and exporters.
Commerce has preliminarily determined that the estimated weighted-
average dumping margins for Genesis Aluminium Industries Sdn. Bhd./
Zenshin Industries Sdn. Bhd. and P.A. Extrusion (M) Sdn. Bhd. under
section 776 of the Act are zero. Consequently, pursuant to section
735(c)(5)(B) of the Act, Commerce's normal practice under these
circumstances has been to calculate the all-others rate as a simple
average of the alleged dumping margin(s) from the petition.\7\ For a
full description of the methodology underlying Commerce's analysis, see
the Preliminary Decision Memorandum.
---------------------------------------------------------------------------
\7\ See, e.g., Notice of Preliminary Determination of Sales at
Less Than Fair Value: Sodium Nitrite from the Federal Republic of
Germany, 73 FR 21909, 21912 (April 23, 2008), unchanged in Notice of
Final Determination of Sales at Less Than Fair Value: Sodium Nitrite
from the Federal Republic of Germany, 73 FR 38986, 38987 (July 8,
2008), and accompanying Issues and Decision Memorandum at Comment 2;
see also Notice of Final Determination of Sales at Less Than Fair
Value: Raw Flexible Magnets from Taiwan, 73 FR 39673, 39674 (July
10, 2008); and Steel Threaded Rod from Thailand: Preliminary
Determination of Sales at Less Than Fair Value and Affirmative
Preliminary Determination of Critical Circumstances, 78 FR 79670,
79671 (December 31, 2013), unchanged in Steel Threaded Rod from
Thailand: Final Determination of Sales at Less Than Fair Value and
Affirmative Final Determination of Critical Circumstances, 79 FR
14476, 14477 (March 14, 2014).
---------------------------------------------------------------------------
Preliminary Determination
For this preliminary determination, Commerce calculated a zero
estimated weighted-average dumping margin for each individually
examined producer and or exporter of the subject merchandise.
Consistent with section 733(b)(3) of the Act, Commerce preliminarily
determines that these individually examined respondents with zero rates
have not made sales of subject merchandise at LTFV.
[[Page 38059]]
------------------------------------------------------------------------
Estimated
weighted-
average
Exporter/producer dumping
margin
(percent)
------------------------------------------------------------------------
Genesis Aluminium Industries Sdn. Bhd./Zenshin Industries 0.00
Sdn. Bhd.\8\...............................................
P.A. Extrusion (M) Sdn. Bhd.\9\............................. 0.00
EL Aluminium Billet (M) Sdn Bhd............................. * 27.51
Kosan Aluminum Extrusion SDN. BHD........................... * 27.51
Winstar Group............................................... * 27.51
All Others.................................................. 26.70
------------------------------------------------------------------------
* Rate based on facts available with adverse inferences.
Suspension of Liquidation
---------------------------------------------------------------------------
\8\ Commerce preliminarily determines that Genesis Aluminium
Industries Sdn. Bhd. and Zenshin Industries Sdn. Bhd. should be
collapsed and treated as a single entity. See the Preliminary
Decision Memorandum.
\9\ Although Commerce selected P.A. Resources Berhad (PARB) as a
mandatory respondent, PARB reported that it is a holding company
that is not involved in the production or exportation of the
merchandise under investigation but that its subsidiary, P.A.
Extrusion (M) Sdn. Bhd., produced the merchandise under
investigation and sold that merchandise to the United States during
the POI. Consequently, Commerce preliminarily determines that the
estimated weighted-average dumping margin applies to P.A. Extrusion
(M) Sdn. Bhd., the only producer and exporter of the merchandise
under consideration owned by PARB. See the Preliminary Decision
Memorandum.
---------------------------------------------------------------------------
In accordance with section 733(d)(2) of the Act, Commerce will
direct U.S. Customs and Border Protection (CBP) to suspend liquidation
of entries of subject merchandise, as described in Appendix I, entered,
or withdrawn from warehouse, for consumption on or after the date of
publication of this notice in the Federal Register. Further, pursuant
to section 733(d)(1)(B) of the Act and 19 CFR 351.205(d), Commerce will
instruct CBP to require a cash deposit equal to the estimated weighted-
average dumping margin or the estimated all-others rate, as follows:
(1) the cash deposit rate for the respondents with above de minimis
dumping margins that are listed in the table above will be equal to the
company-specific estimated weighted-average dumping margins determined
in this preliminary determination; (2) if the exporter is not a company
identified in the table above, but the producer is, then the cash
deposit rate will be equal to the company-specific estimated weighted-
average dumping margin established for that producer of the subject
merchandise, except as explained below; and (3) the cash deposit rate
for all other producers and exporters will be equal to the all-others
estimated weighted-average dumping margin.
Because the estimated weighted-average dumping margins for Genesis
Aluminium Industries Sdn. Bhd/Zenshin Industries Sdn. Bhd. and P.A.
Extrusion (M) Sdn. Bhd. are zero, entries of subject merchandise
produced and exported by these companies will not be subject to
suspension of liquidation or cash deposit requirements. In such
situations, Commerce applies the exclusion to the provisional measures
to the producer/exporter combination that was examined in the
investigation. Accordingly, Commerce is directing CBP not to suspend
the liquidation of entries of subject merchandise that was exported by
Genesis Aluminium Industries Sdn. Bhd/Zenshin Industries Sdn. Bhd. and
produced by Genesis Aluminium Industries Sdn. Bhd/Zenshin Industries
Sdn. Bhd. or subject merchandise that was exported by P.A. Extrusion
(M) Sdn. Bhd. and produced by P.A. Extrusion (M) Sdn. Bhd. Entries of
shipments of subject merchandise from these companies in any other
producer/exporter combination, or by third parties that sourced subject
merchandise from the excluded producer/exporter combination, are
subject to the provisional measures at the all-others rate.
Should the final estimated weighted-average dumping margin be zero
or de minimis for the producer/exporter combinations identified above,
entries of shipments of subject merchandise from these producer/
exporter combinations will be excluded from the potential antidumping
duty order. Such exclusions are not applicable to merchandise exported
to the United States by these respondents in any other producer/
exporter combinations or by third parties that sourced subject
merchandise from the excluded producer/exporter combinations.
These suspension of liquidation instructions will remain in effect
until further notice.
Disclosure
Commerce intends to disclose to parties to the proceeding the
calculations and analysis it performed in this preliminary
determination within five days of public announcement or, if there is
no public announcement, within five days of the date of publication of
this notice in the Federal Register, in accordance with 19 CFR
351.224(b).
Verification
As provided in section 782(i)(1) of the Act, Commerce intends to
verify the information relied upon in making its final determination.
Public Comment
For scope-related comments, please refer to the Preliminary Scope
Decision Memo II for the deadlines for scope comments. After the
submission of scope comments, Commerce will set a schedule for the
submission of case and rebuttal briefs limited to scope issues.
Case briefs or other written comments on non-scope issues may be
submitted to the Assistant Secretary for Enforcement and Compliance no
later than seven days after the date on which the last verification
report is issued in this investigation.\10\ Rebuttal briefs, limited to
issues raised in the case briefs, may be filed not later than five days
after the date for filing case briefs.\11\ Interested parties who
submit case or rebuttal briefs in this proceeding must submit: (1) a
table of contents listing each issue; and (2) a table of
authorities.\12\
---------------------------------------------------------------------------
\10\ See 19 CFR 351.309(c)(1)(i); see also 19 CFR 351.303 (for
general filing requirements).
\11\ See 19 CFR 351.309(d); see also Administrative Protective
Order, Service, and Other Procedures in Antidumping and
Countervailing Duty Proceedings, 88 FR 67069, 67077 (September 29,
2023) (APO and Service Final Rule).
\12\ See 19 CFR 351.309(c)(2) and (d)(2).
---------------------------------------------------------------------------
As provided under 19 CFR 351.309(c)(2) and (d)(2), in prior
proceedings we have encouraged interested parties to provide an
executive summary of their brief that should be limited to five pages
total, including footnotes. In this investigation, we instead request
that interested parties provide, at the beginning of their briefs a
public, executive summary for each issue raised in their briefs.\13\
Further, we request that interested parties limit their public
executive summary of each issue to no more than 450 words, not
including citations. We intend to use the public executive summaries as
the basis of the comment summaries included in the issues and decision
memorandum that will accompany the final determination in this
investigation. We request that interested parties include footnotes for
relevant citations in the executive summary of each issue.
---------------------------------------------------------------------------
\13\ We use the term ``issue'' here to describe an argument that
Commerce would normally address in a comment of the Issues and
Decision Memorandum.
---------------------------------------------------------------------------
Note that Commerce has amended certain of its requirements
pertaining to the service of documents in 19 CFR 351.303(f).\14\
---------------------------------------------------------------------------
\14\ See APO and Service Final Rule.
---------------------------------------------------------------------------
Pursuant to 19 CFR 351.310(c), interested parties who wish to
request a hearing, limited to issues raised in the case and rebuttal
briefs, must submit a written request to the Assistant
[[Page 38060]]
Secretary for Enforcement and Compliance, U.S. Department of Commerce,
within 30 days after the date of publication of this notice in the
Federal Register. Requests should contain (1) the party's name,
address, and telephone number; (2) the number of participants and
whether any participant is a foreign national; and (3) a list of the
issues to be discussed. If a request for a hearing is made, Commerce
intends to hold the hearing at a time and date to be determined.
Parties should confirm by telephone the date, time, and location of the
hearing two days before the scheduled date.
Postponement of Final Determination and Extension of Provisional
Measures
Section 735(a)(2) of the Act provides that a final determination
may be postponed until not later than 135 days after the date of the
publication of the preliminary determination if, in the event of an
affirmative preliminary determination, a request for such postponement
is made by exporters who account for a significant proportion of
exports of the subject merchandise, or in the event of a negative
preliminary determination, a request for such postponement is made by
the petitioner. Pursuant to 19 CFR 351.210(e)(2), Commerce requires
that requests by exporters for postponement of the final determination
be accompanied by a request for extension of provisional measures from
a four-month period to a period not more than six months in duration.
On April 17 and 18, 2024, pursuant to 19 CFR 351.210(e), Genesis
Aluminium Industries Sdn. Bhd. and P.A. Resources Berhad, respectively,
requested that Commerce postpone the final determination and that
provisional measures be extended to a period not to exceed six
months.\15\ In accordance with section 735(a)(2)(A) of the Act and 19
CFR 351.210(b)(2)(ii), because: (1) the preliminary determination is
affirmative; (2) the requesting exporters account for a significant
proportion of exports of the subject merchandise; and (3) no compelling
reasons for denial exist, Commerce is postponing the final
determination and extending the provisional measures from a four-month
period to a period not greater than six months. Accordingly, Commerce
will make its final determination no later than 135 days after the date
of publication of this notice of preliminary determination in the
Federal Register.
---------------------------------------------------------------------------
\15\ See Genesis Aluminium Industries Sdn. Bhd.'s Letter,
``Genesis Request to Postpone Final Determination,'' dated April 17,
2024; see also P.A. Resources Berhad's Letter, ``Request to Extend
Final Determination,'' dated April 18, 2024.
---------------------------------------------------------------------------
U.S. International Trade Commission Notification
In accordance with section 733(f) of the Act, Commerce will notify
the U.S. International Trade Commission (ITC) of its preliminary
determination of sales at LTFV. If the final determination is
affirmative, the ITC will determine before the later of 120 days after
the date of this preliminary determination or 45 days after the final
determination whether imports of subject merchandise are materially
injuring, or threaten material injury to, the U.S. industry.
Notification to Interested Parties
This determination is issued and published in accordance with
sections 733(f) and 777(i)(1) of the Act, and 19 CFR 351.205(c).
Dated: May 1, 2024.
Ryan Majerus,
Deputy Assistant Secretary for Policy and Negotiations, performing the
non-exclusive functions and duties of the Assistant Secretary for
Enforcement and Compliance.
Appendix I--Scope of the Investigation
The merchandise subject to this investigation are aluminum
extrusions, regardless of form, finishing, or fabrication, whether
assembled with other parts or unassembled, whether coated, painted,
anodized, or thermally improved. Aluminum extrusions are shapes and
forms, produced by an extrusion process, made from aluminum alloys
having metallic elements corresponding to the alloy series
designations published by the Aluminum Association commencing with
the numbers 1, 3, and 6 (or proprietary equivalents or other
certifying body equivalents). Specifically, subject aluminum
extrusions made from an aluminum alloy with an Aluminum Association
series designation commencing with the number 1 contain not less
than 99 percent aluminum by weight. Subject aluminum extrusions made
from an aluminum alloy with an Aluminum Association series
designation commencing with the number 3 contain manganese as the
major alloying element, with manganese accounting for not more than
3.0 percent of total materials by weight. Subject aluminum
extrusions made from an aluminum alloy with an Aluminum Association
series designation commencing with the number 6 contain magnesium
and silicon as the major alloying elements, with magnesium
accounting for at least 0.1 percent but not more than 2.0 percent of
total materials by weight, and silicon accounting for at least 0.1
percent but not more than 3.0 percent of total materials by weight.
The scope also includes merchandise made from an aluminum alloy with
an Aluminum Association series designation commencing with the
number 5 (or proprietary equivalents or other certifying body
equivalents) that have a magnesium content accounting for up to but
not more than 2.0 percent of total materials by weight.
The country of origin of the aluminum extrusion is determined by
where the metal is extruded (i.e., pressed through a die).
Aluminum extrusions are produced and imported in a wide variety
of shapes and forms, including, but not limited to, hollow profiles,
other solid profiles, pipes, tubes, bars, and rods. Aluminum
extrusions that are drawn subsequent to extrusion (drawn aluminum)
are also included in the scope.
Subject aluminum extrusions are produced and imported with a
variety of coatings and surface treatments, and types of
fabrication. The types of coatings and treatments applied to
aluminum extrusions include, but are not limited to, extrusions that
are mill finished (i.e., without any coating or further finishing),
brushed, buffed, polished, anodized (including bright dip), liquid
painted, electroplated, chromate converted, powder coated,
sublimated, wrapped, and/or bead blasted. Subject aluminum
extrusions may also be fabricated, i.e., prepared for assembly, or
thermally improved. Such operations would include, but are not
limited to, extrusions that are cut-to-length, machined, drilled,
punched, notched, bent, stretched, stretch-formed, hydroformed,
knurled, swedged, mitered, chamfered, threaded, spun, etched, and
engraved. Performing such operations in third countries does not
otherwise remove the merchandise from the scope of the
investigations.
The types of products that meet the definition of subject
merchandise include but are not limited to, the aluminum extrusion
portions of vehicle roof rails and sun/moon roof framing, solar
panel racking rails and framing, tradeshow display fixtures and
framing, parts for tents or clear span structures, fence posts,
drapery rails or rods, electrical conduits, door thresholds,
flooring trim, electric vehicle battery trays, heat sinks, signage
or advertising poles, telescoping poles, or cleaning system
components.
Aluminum extrusions may be heat sinks, which are fabricated
aluminum extrusions that dissipate heat away from a heat source and
may serve other functions, such as structural functions. Heat sinks
come in a variety of sizes and shapes, including but not limited to
a flat electronic heat sink, which is a solid aluminum extrusion
with at least one flat side used to mount electronic or mechanical
devices; a heat sink that is a housing for electronic controls or
motors; lighting heat sinks, which dissipate heat away from LED
devices; and process and exchange heat sinks, which are tube
extrusions with fins or plates used to hold radiator tubing. Heat
sinks are included in the scope, regardless of whether the design
and production of the heat sinks are organized around meeting
specified thermal performance requirements and regardless of whether
they have been tested to comply with such requirements. For purposes
of the investigations on aluminum extrusions from the People's
Republic of China, only heat sinks designed and produced around
meeting specified thermal performance requirements and tested to
comply with such requirements are included in the scope. Excluded
from the scope of the investigations are large, multi-
[[Page 38061]]
finned extruded aluminum heat sinks designed to dissipate heat,
meeting the following criteria: (1) an aspect ratio (defined as the
ratio of the area of a void in an extrusion to the size of the
smallest gap opening at the entrance of that void and calculated by
dividing the void area by the square of the gap opening) greater
than 15 to 1; or (2) the circumscribing circle diameter (defined as
the diameter of the smallest circle that will entirely enclose the
extrusion's cross-sectional profile) rounded up to the next half
inch, exceeds 10 inches, and the weight-per-foot (defined as the
theoretical weight of the profile as extruded prior to any machining
that may remove material and calculated by multiplying the area of
the profile in square inches by 1.2) exceeds 3.50 pounds per foot.
Merchandise that is comprised solely of aluminum extrusions or
aluminum extrusions and fasteners, whether assembled at the time of
importation or unassembled, is covered by the scope in its entirety.
The scope also includes aluminum extrusions contained in
merchandise that is a part or subassembly of a larger whole, whether
or not the merchandise also contains a component other than aluminum
extrusions that is beyond a fastener. Such merchandise may be either
assembled or unassembled at the time of importation. A ``part or
subassembly'' is defined as a unit designed to be attached to, or
incorporated with, one or more other units or components into a
larger completed product. Only the aluminum extrusion portion of the
merchandise described in this paragraph, whether assembled or
unassembled, is subject merchandise included in the scope and
subject to duties. Examples of merchandise that is a part or
subassembly of a larger whole include, but are not limited to,
window parts or subassemblies; door unit parts or subassemblies;
shower and bath parts or subassemblies; solar panel mounting
systems; fenestration system parts or subassemblies, such as curtain
wall and window wall units and parts or subassemblies of
storefronts; furniture parts or subassemblies; appliance parts or
subassemblies, such as fin evaporator coils and systems for
refrigerators; railing or deck system parts or subassemblies; fence
system parts or subassemblies; motor vehicle parts or subassemblies,
such as bumpers for motor vehicles; trailer parts or subassemblies,
such as side walls, flooring, and roofings; electric vehicle
charging station parts or subassemblies; or signage or advertising
system parts or subassemblies. Parts or subassemblies described by
this paragraph that are subject to duties in their entirety pursuant
to existing antidumping and countervailing duty orders (defined as
those antidumping and countervailing duty orders that are in effect
as of the date of publication of the order resulting from this
investigation) are excluded from the scope of the investigation. Any
part or subassembly that otherwise meets the requirements of this
scope and that is not covered by other antidumping and/or
countervailing duty orders remains subject to the scope of the
investigations.
The scope excludes aluminum extrusions contained in fully and
permanently assembled merchandise, if the assembled merchandise is
not a part or subassembly of a larger whole. To be excluded under
this paragraph, the assembled merchandise must also contain a
component other than aluminum extrusions, beyond fasteners. In
addition, to be excluded under this paragraph, the assembled
merchandise must be ready for use as imported, without undergoing
after importation any processing, fabrication, finishing, or
assembly or the addition of parts or material (with the exception of
consumable parts or material or interchangeable media or tooling).
The scope also excludes aluminum extrusions contained in
unassembled merchandise if the unassembled merchandise is not a part
or subassembly of a larger whole. To be excluded under this
paragraph, the unassembled merchandise must also contain a component
other than aluminum extrusions, beyond fasteners. In addition, to be
excluded under this paragraph, the unassembled merchandise must be a
packaged combination of parts that is ready to be assembled as
imported, without undergoing after importation any processing,
fabrication, or finishing or the addition of parts or material (with
the exception of consumable parts or material or interchangeable
media or tooling). To be excluded under this paragraph, the
unassembled merchandise must be sold and enter as a discrete kit on
one Customs entry form.
Examples of such excluded assembled and unassembled merchandise
include windows with glass, door units with door panel and glass,
motor vehicles, trailers, furniture, appliances, and solar panels
and solar modules.
The scope also excludes merchandise containing multiple
subassemblies of a larger whole with non-extruded aluminum
components beyond fasteners. A subassembly that meets the definition
of subject merchandise, including any product expressly identified
as subject merchandise in this scope, can only be excluded if it is
fully and permanently assembled with at least one other different
subassembly, and where (1) at least one of the subassemblies, if
entered individually, would not itself be subject to the scope; (2)
the aluminum extrusions within the merchandise collectively account
for 50 percent or less of the actual weight of the combined multiple
subassemblies (without including any non-extruded aluminum fasteners
in the calculations); and (3) the aluminum extrusions within the
merchandise collectively account for 50 percent or less of the
number of pieces of the combined multiple subassemblies (without
including any non-extruded aluminum fasteners in the calculations).
The scope also includes aluminum extrusions that have been
further processed in a third country, including, but not limited to,
the finishing and fabrication processes described above, assembly,
whether with other aluminum extrusion components or with non-
aluminum extrusion components, or any other processing that would
not otherwise remove the merchandise from the scope if performed in
the country of manufacture of the in-scope product. Third country
processing; finishing; and/or fabrication, including those processes
described in the scope, does not alter the country of origin of the
subject aluminum extrusions.
The following aluminum extrusion products are excluded: aluminum
extrusions made from an aluminum alloy with an Aluminum Association
series designations commencing with the number 2 (or proprietary
equivalents or other certifying body equivalents) and containing in
excess of 1.5 percent copper by weight; aluminum extrusions made
from an aluminum alloy with an Aluminum Association series
designation commencing with the number 5 (or proprietary equivalents
or other certifying body equivalents) and containing in excess of
2.0 percent magnesium by weight; and aluminum extrusions made from
an aluminum alloy with an Aluminum Association series designation
commencing with the number 7 (or proprietary equivalents or other
certifying body equivalents) and containing in excess of 2.0 percent
zinc by weight.
The scope also excludes aluminum alloy sheet or plates produced
by means other than the extrusion process, such as aluminum products
produced by a method of continuous casting or rolling. Cast aluminum
products are also excluded. The scope also excludes unwrought
aluminum in any form.
The scope also excludes collapsible tubular containers composed
of metallic elements corresponding to alloy code 1080A as designated
by the Aluminum Association (not including proprietary equivalents
or other certifying body equivalents) where the tubular container
(excluding the nozzle) meets each of the following dimensional
characteristics: (1) length of 37 millimeters (mm) or 62 mm; (2)
outer diameter of 11.0 mm or 12.7 mm; and (3) wall thickness not
exceeding 0.13 mm.
Also excluded from the scope are extruded drawn solid profiles
made from an aluminum alloy with the Aluminum Association series
designation commencing with the number 1, 3, or 6 (or proprietary
equivalents or other certifying body equivalents), including
variants on individual alloying elements not to circumvent the other
Aluminum Association series designations, which meet each of the
following characteristics: (1) solid cross sectional area greater
than 62.4 mm\2\ and less than 906 mm\2\, (2) minimum electrical
conductivity of 58% of the international annealed copper standard
(IACS) or maximum resistivity of 2.97 [mu][Omega]/cm, (3) a
uniformly applied nonelectrically conductive temperature-resistant
coating co-extruded over characteristic (1) of either polyamide,
cross-linked polyethylene, or silicone rubber material which meets
the following standards: (a) Vicat A temperature threshold of >140
degrees Celsius, (b) flammability requirements of UL 94V-0, and (c)
a minimum coating thickness of 0.10 mm and maximum coating thickness
of 2.0 mm, with a maximum thickness tolerance of +/-0.20 mm, (4)
characteristic 3 may or may not be encapsulated with a ``Precision
Drawn Tubing,'' wall thicknesses less than 1.2 mm, which is
mechanically fixed in place, and (5)
[[Page 38062]]
packaged in straight lengths, bent or formed and/or attached to
hardware.
Also excluded from the scope are extruded tubing and drawn over
a ID plug and through a OD die made from an aluminum alloy with the
Aluminum Association series designation commencing with the number
3, 5, or 6 (or proprietary equivalents or other certifying body
equivalents), including variants on individual alloying elements not
to circumvent the other Aluminum Association series designations,
which meet each of the following characteristics: (1) an outside
mean diameter no greater than 30 mm with a tolerance less than or
equal to +/-0.10 mm, (2) uniform wall thickness no greater than 2.7
mm with wall tolerances less than or equal to +/-0.1 mm, (3) may be
coated with materials, including zinc, such that the coating
material weight is no less than 3 g/m\2\ and no greater than 30 g/
m\2\, and (4) packaged in continuous coils, straight lengths, bent
or formed.
The scope also excludes fully and permanently assembled glass
refrigerator shelves with decorative aluminum trim meeting the
following characteristics: (1) aluminum trim meeting Aluminum
Association series 6063-T5 designation that is anodized; (2)
aluminum trim length of not more than 800 mm, and (3) aluminum trim
width of not more than 40 mm. Such fully and permanently assembled
glass refrigerator shelves include other components in addition to
the aluminum trim, including, but not limited to, glass, steel, and
plastic. Only fully and permanently assembled glass refrigerator
shelves that require no further processing, fabrication, finishing,
assembly, or the addition of any parts or material are excluded.
Imports of glass refrigerator shelves are classified under HTSUS
8418.99.8050, which is being included for convenience.
Also excluded from the scope of this investigation is certain
rectangular wire, imported in bulk rolls or precut strips and
produced from continuously cast rolled aluminum wire rod, which is
subsequently extruded to dimension to form rectangular wire with or
without rounded edges. The product is made from aluminum alloy grade
1070 or 1370 (not including proprietary equivalents or other
certifying body equivalents), with no recycled metal content
allowed. The dimensions of the wire are 2.95 mm to 6.05 mm in width,
and 0.65 mm to 1.25 mm in thickness. Imports of rectangular wire are
provided for under Harmonized Tariff Schedule of the United States
(HTSUS) subheadings 7605.19.0000, 7604.10.5000, or 7616.99.5190.
Also excluded from the scope of the antidumping and
countervailing duty investigations on aluminum extrusions from the
People's Republic of China are all products covered by the scope of
the antidumping and countervailing duty orders on Aluminum
Extrusions from the People's Republic of China. See Aluminum
Extrusions from the People's Republic of China: Antidumping Duty
Order, 76 FR 30650 (May 26, 2011); and Aluminum Extrusions from the
People's Republic of China: Countervailing Duty Order, 76 FR 30653
(May 26, 2011) (collectively, Aluminum Extrusions from the People's
Republic of China). Solely for the investigations on aluminum
extrusions from the People's Republic of China, the following is an
exhaustive list of products where the aluminum extrusion portions
thereof meet the definition of subject merchandise. The language
contained in the rest of the scope applies to this exhaustive list
of products. Merchandise that is not included in the following list
that meets the definition of subject merchandise in the 2011
antidumping and countervailing duty orders on Aluminum Extrusions
from the People's Republic of China remains subject to the earlier
orders. No other section of this scope language that provides
examples of subject merchandise is exhaustive.
The aluminum extrusion portions of the following products are
included in the scope of the investigations on aluminum extrusions
from the People's Republic of China, whether assembled or
unassembled: heat sinks as described above; cleaning system
components like mops and poles; banner stands/back walls; fabric
wall systems; drapery rails; side mount valve controls; water heater
anodes; solar panel mounting systems; automotive heating and cooling
system components; assembled motor cases with stators; louver
assemblies; event d[eacute]cor; window wall units and parts; trade
booths; micro channel heat exchangers; telescoping poles, pole
handles, and pole attachments; flagpoles; wind sign frames; foreline
hose assembly; electronics enclosures; parts and subassemblies for
storefronts, including portal sets; light poles; air duct registers;
outdoor sporting goods parts and subassemblies; glass refrigerator
shelves; aluminum ramps; handicap ramp system parts and
subassemblies; frames and parts for tents and clear span structures;
parts and subassemblies for screen enclosures, patios, and sunrooms;
parts and subassemblies for walkways and walkway covers; aluminum
extrusions for Light Emitting Diode (LED) lights; parts and
subassemblies for screen, storm, and patio doors; pontoon boat parts
and subassemblies, including rub rails, flooring, decking, transom
structures, canopy systems, seating; boat hulls, framing, ladders,
and transom structures; parts and subassemblies for docks, piers,
boat lifts and mounting; recreational and boat trailer parts and
subassemblies, including subframes, crossmembers, and gates; solar
tracker assemblies with gears; garage door framing systems; door
threshold and sill assemblies; highway and bridge signs; bridge,
street, and highway rails; scaffolding, including planks and struts;
railing and support systems; parts and subassemblies for exercise
equipment; weatherstripping; door bottom and sweeps; door seals;
floor transitions and trims; parts and subassemblies for modular
walls and office furniture; truck trailer parts and subassemblies;
boat cover poles, outrigger poles, and rod holders; bleachers and
benches; parts and subassemblies for elevators, lifts, and
dumbwaiters; parts and subassemblies for mirror and framing systems;
window treatments; parts and subassemblies for air foils and fans;
bus and Recreational Vehicle (RV) window frames; sliding door rails;
dock ladders; parts and subassemblies for RV frames and trailers;
awning, canopy, and sunshade structures and their parts and
subassemblies; marine motor mounts; linear lighting housings; and
cluster mailbox systems.
Imports of the subject merchandise are primarily provided for
under the following categories of the HTSUS: 7604.10.1000;
7604.10.3000; 7604.10.5000; 7604.21.0010; 7604.21.0090;
7604.29.1010; 7604.29.1090; 7604.29.3060; 7604.29.3090;
7604.29.5050; 7604.29.5090; 7608.10.0030; 7608.10.0090;
7608.20.0030; 7608.20.0090; 7609.00.0000; 7610.10.0010;
7610.10.0020; 7610.10.0030; 7610.90.0040; and 7610.90.0080.
Imports of the subject merchandise, including subject
merchandise entered as parts of other products, may also be
classifiable under the following additional HTSUS categories, as
well as other HTSUS categories: 6603.90.8100; 7606.12.3091;
7606.12.3096; 7615.10.2015; 7615.10.2025; 7615.10.3015;
7615.10.3025; 7615.10.5020; 7615.10.5040; 7615.10.7125;
7615.10.7130; 7615.10.7155; 7615.10.7180; 7615.10.9100;
7615.20.0000; 7616.10.9090; 7616.99.1000; 7616.99.5130;
7616.99.5140; 7616.99.5190; 8302.10.3000; 8302.10.6030;
8302.10.6060; 8302.10.6090; 8302.20.0000; 8302.30.3010;
8302.30.3060; 8302.41.3000; 8302.41.6015; 8302.41.6045;
8302.41.6050; 8302.41.6080; 8302.42.3010; 8302.42.3015;
8302.42.3065; 8302.49.6035; 8302.49.6045; 8302.49.6055;
8302.49.6085; 8302.50.0000; 8302.60.3000; 8302.60.9000;
8305.10.0050; 8306.30.0000; 8414.59.6590; 8415.90.8045;
8418.99.8005; 8418.99.8050; 8418.99.8060; 8419.50.5000;
8419.90.1000; 8422.90.0640; 8424.90.9080; 8473.30.2000;
8473.30.5100; 8479.89.9599; 8479.90.8500; 8479.90.9596;
8481.90.9060; 8481.90.9085; 8486.90.0000; 8487.90.0080;
8503.00.9520; 8508.70.0000; 8513.90.2000; 8515.90.2000;
8516.90.5000; 8516.90.8050; 8517.71.0000; 8517.79.0000;
8529.90.7300; 8529.90.9760; 8536.90.8585; 8538.10.0000;
8541.90.0000; 8543.90.8885; 8547.90.0020; 8547.90.0030;
8547.90.0040; 8708.10.3050; 8708.29.5160; 8708.80.6590;
8708.99.6890; 8807.30.0060; 9031.90.9195; 9401.99.9081;
9403.99.1040; 9403.99.9010; 9403.99.9015; 9403.99.9020;
9403.99.9040; 9403.99.9045; 9405.99.4020; 9506.11.4080;
9506.51.4000; 9506.51.6000; 9506.59.4040; 9506.70.2090;
9506.91.0010; 9506.91.0020; 9506.91.0030; 9506.99.0510;
9506.99.0520; 9506.99.0530; 9506.99.1500; 9506.99.2000;
9506.99.2580; 9506.99.2800; 9506.99.5500; 9506.99.6080;
9507.30.2000; 9507.30.4000; 9507.30.6000; 9507.30.8000;
9507.90.6000; and 9603.90.8050.
While HTSUS subheadings are provided for convenience and customs
purposes, the written description of the scope is dispositive.
Appendix II--List of Topics Discussed in the Preliminary Decision
Memorandum
I. Summary
II. Background
III. Period of Investigation
IV. Affiliation and Single Entity Treatment
V. Application of Facts Available with Adverse Inferences
VI. Discussion of the Methodology
VII. Currency Conversion
[[Page 38063]]
VIII. Recommendation
[FR Doc. 2024-09937 Filed 5-6-24; 8:45 am]
BILLING CODE 3510-DS-P