[Federal Register Volume 89, Number 80 (Wednesday, April 24, 2024)]
[Notices]
[Pages 31220-31221]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2024-08686]


-----------------------------------------------------------------------

DEPARTMENT OF LABOR

Occupational Safety and Health Administration

[Docket No. OSHA-2007-0039]


Intertek Testing Services NA, Inc.: Grant of Expansion of 
Recognition

AGENCY: Occupational Safety and Health Administration (OSHA), Labor.

ACTION: Notice.

-----------------------------------------------------------------------

SUMMARY: In this notice, OSHA announces the final decision to expand 
the scope of recognition for Intertek Testing Services NA, Inc., 
(ITSNA) as a Nationally Recognized Testing Laboratory (NRTL).

DATES: The expansion of the scope of recognition becomes effective on 
April 24, 2024.

FOR FURTHER INFORMATION CONTACT: Information regarding this notice is 
available from the following sources:
    Press inquiries: Contact Mr. Frank Meilinger, Director, OSHA Office 
of Communications, U.S. Department of Labor; telephone (202) 693-1999 
or email [email protected].
    General and technical information: Contact Mr. Kevin Robinson, 
Director, Office of Technical Programs and Coordination Activities, 
Directorate of Technical Support and Emergency Management, Occupational 
Safety and Health Administration, U.S. Department of Labor; telephone 
(202) 693-1911 or email [email protected].

SUPPLEMENTARY INFORMATION:

I. Notice of the Final Decision

    OSHA hereby gives notice of the expansion of the scope of 
recognition of Intertek Testing Services NA, Inc. (ITSNA) as a NRTL. 
ITSNA's expansion covers the addition of four test standards to the 
NRTL scope of recognition.
    OSHA recognition of a NRTL signifies that the organization meets 
the requirements specified in 29 CFR 1910.7. Recognition is an 
acknowledgment that the organization can perform independent safety 
testing and certification of the specific products covered within the 
scope of recognition. Each NRTL's scope of recognition includes: (1) 
the type of products the NRTL may test, with each type specified by the 
applicable test standard; and (2) the recognized site(s) that has/have 
the technical capability to perform the product-testing and product-
certification activities for test standards within the NRTL's scope. 
Recognition is not a delegation or grant of government authority; 
however, recognition enables employers to use products approved by the 
NRTL to meet OSHA standards that require product testing and 
certification.
    The agency processes applications by a NRTL for initial recognition 
and for an expansion or renewal of this recognition, following 
requirements in appendix A to 29 CFR 1910.7. This appendix requires 
that the agency publish two notices in the Federal Register in 
processing an application. In the first notice, OSHA announces the 
application and provides a preliminary finding. In the second notice, 
the agency provides a final decision on the application. These notices 
set forth the NRTL's scope of recognition or modifications of that 
scope. OSHA maintains an informational web page for each NRTL, 
including ITSNA, which details the NRTL's scope of recognition. These 
pages are available from the OSHA website at http://www.osha.gov/dts/otpca/nrtl/index.html.
    ITSNA submitted an application dated February 15, 2021 (OSHA-2007-
0039-0055), requesting the addition of four test standards to the NRTL 
scope of recognition. OSHA staff performed a detailed analysis of the 
application packet and reviewed other pertinent information. OSHA did 
not perform any on-site reviews in relation to this application.
    OSHA published the preliminary notice announcing ITSNA's expansion 
application in the Federal Register on March 27, 2024 (89 FR 21284). 
The agency requested comments by April 11, 2024, but it received no 
comments in response to this notice.
    To obtain or review copies of all public documents pertaining to 
the ITSNA application, go to http://www.regulations.gov or contact the 
Docket Office, Occupational Safety and Health Administration, U.S. 
Department of Labor. Docket No. OSHA-2007-0039 contains all materials 
in the record concerning ITSNA's recognition. Contact the OSHA Docket 
Office at (202) 693-2350 (TTY (877) 889-5627) for assistance in 
locating docket submissions.

II. Final Decision and Order

    OSHA staff examined ITSNA's expansion application, its capability 
to meet the requirements of the test standards, and other pertinent 
information. Based on its review of this evidence, OSHA finds that 
ITSNA meets the requirements of 29 CFR 1910.7 for expansion of its 
recognition, subject to the limitations and conditions listed in this 
notice. OSHA, therefore, is proceeding with this final notice to grant 
ITSNA's expanded scope of recognition. OSHA limits the expansion

[[Page 31221]]

of ITSNA's recognition to testing and certification of products for 
demonstration of conformance to the test standards listed below in 
Table 1.

 Table 1--Appropriate Test Standards for Inclusion in ITSNA's NRTL Scope
                             of Recognition
------------------------------------------------------------------------
           Test standard                     Test standard title
------------------------------------------------------------------------
UL 1973...........................  Batteries for Use in Stationary,
                                     Vehicle Auxiliary Power and Light
                                     Electric Rail (LER) Applications.
UL 2271...........................  Batteries for Use in Light Electric
                                     Vehicle (LEV) Applications.
UL 2524...........................  In-Building 2-Way Emergency Radio
                                     Communication Enhancement Systems.
UL 2743...........................  Portable Power Packs.
------------------------------------------------------------------------

    The American National Standards Institute (ANSI) may approve the 
test standards listed above as American National Standards. However, 
for convenience, we may use the designation of the standards-developing 
organization for the standard as opposed to the ANSI designation. Under 
the NRTL Program's policy (see OSHA Instruction CPL 01-00-004, Chapter 
2, Section VIII), any NRTL recognized for a particular test standard 
may use either the proprietary version of the test standard or the ANSI 
version of that standard. Contact ANSI to determine whether a test 
standard is currently ANSI-approved.

A. Conditions

    In addition to those conditions already required by 29 CFR 1910.7, 
ITSNA must abide by the following conditions of the recognition:
    1. ITSNA must inform OSHA as soon as possible, in writing, of any 
change of ownership, facilities, or key personnel, and of any major 
change in its operations as a NRTL, and provide details of the 
change(s);
    2. ITSNA must meet all the terms of its recognition and comply with 
all OSHA policies pertaining to this recognition; and
    3. ITSNA must continue to meet the requirements for recognition, 
including all previously published conditions on ITSNA's scope of 
recognition, in all areas for which it has recognition.
    Pursuant to the authority in 29 CFR 1910.7, OSHA hereby expands the 
scope of recognition of ITSNA as a NRTL, subject to the limitations and 
conditions specified above.

III. Authority and Signature

    James S. Frederick, Deputy Assistant Secretary of Labor for 
Occupational Safety and Health, authorized the preparation of this 
notice. Accordingly, the agency is issuing this notice pursuant to 29 
U.S.C. 657(g)(2), Secretary of Labor's Order No. 8-2020 (85 FR 58393, 
Sept. 18, 2020), and 29 CFR 1910.7.

    Signed at Washington, DC, on April 17, 2024.
James S. Frederick,
Deputy Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2024-08686 Filed 4-23-24; 8:45 am]
BILLING CODE 4510-26-P