[Federal Register Volume 89, Number 20 (Tuesday, January 30, 2024)]
[Notices]
[Pages 5938-5939]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2024-01774]


-----------------------------------------------------------------------

DEPARTMENT OF LABOR

Occupational Safety and Health Administration

[Docket No. OSHA-2007-0039]


Intertek Testing Services NA, Inc.: Grant of Expansion of 
Recognition

AGENCY: Occupational Safety and Health Administration (OSHA), Labor.

ACTION: Notice.

-----------------------------------------------------------------------

SUMMARY: In this notice, OSHA announces the final decision to expand 
the scope of recognition for Intertek Testing Services NA, Inc., as a 
Nationally Recognized Testing Laboratory (NRTL).

DATES: The expansion of the scope of recognition becomes effective on 
January 30, 2024.

FOR FURTHER INFORMATION CONTACT: Information regarding this notice is 
available from the following sources:
    Press inquiries: Contact Mr. Frank Meilinger, Director, OSHA Office 
of Communications, phone: (202) 693-1999 or email: 
[email protected].
    General and technical information: Contact Mr. Kevin Robinson, 
Director, Office of Technical Programs and Coordination Activities, 
Directorate of Technical Support and Emergency Management, Occupational 
Safety and Health Administration, phone: (202) 693-1911 or email: 
[email protected].

SUPPLEMENTARY INFORMATION:

I. Notice of Final Decision

    OSHA hereby gives notice of the expansion of the scope of 
recognition of Intertek Testing Services NA, Inc. (ITSNA) as a NRTL. 
ITSNA's expansion covers the addition of one test standard to the NRTL 
scope of recognition.
    OSHA recognition of a NRTL signifies that the organization meets 
the requirements specified in 29 CFR 1910.7. Recognition is an 
acknowledgment that the organization can perform independent safety 
testing and certification of the specific products covered within the 
scope of recognition. Each NRTL's scope of recognition includes (1) the 
type of products the NRTL may test, with each type specified by the 
applicable test standard; and (2) the recognized site(s) that has/have 
the technical capability to perform the product-testing and product-
certification activities for test standards within the NRTL's scope. 
Recognition is not a delegation or grant of government authority; 
however, recognition enables employers to use products approved by the 
NRTL to meet OSHA standards that require product testing and 
certification.
    The agency processes an application by a NRTL for initial 
recognition and for an expansion or renewal of this recognition, 
following requirements in Appendix A, 29 CFR 1910.7. This appendix 
requires that the agency publish two notices in the Federal Register in 
processing an application. In the first notice, OSHA announces the 
application and provides the preliminary finding. In the second notice, 
the agency provides the final decision on the application. These 
notices set forth the NRTL's scope of recognition or modifications of 
that scope. OSHA maintains an informational web page for each NRTL, 
including ITSNA, which details the NRTL's scope of recognition. These 
pages are available from the OSHA website at http://www.osha.gov/dts/otpca/nrtl/index.html.
    ITSNA submitted an application dated April 5, 2023 (OSHA-2007-0039-
0051), requesting the addition of one test standard to the NRTL scope 
of recognition. OSHA staff performed a detailed analysis of the 
application packet and reviewed other pertinent information. OSHA did 
not perform any on-site reviews in relation to this application.
    OSHA published the preliminary notice announcing ITSNA's expansion 
application in the Federal Register on December 18, 2023 (88 FR 87460). 
The agency requested comments by January 2, 2024, but it received no 
comments in response to this notice. OSHA is now proceeding with this 
final grant of expansion of ITSNA's NRTL recognition.
    To obtain or review copies of all public documents pertaining to 
the ITSNA applications, go to https://www.regulations.gov or contact 
the Docket Office, Occupational Safety and Health Administration, U.S. 
Department of Labor. Docket No. OSHA-2007-0039 contains all materials 
in the record concerning ITSNA's recognition. All submissions, 
including copyrighted material, are available for inspection through 
the OSHA Docket Office. Contact the OSHA Docket Office at (202) 693-
2350 for assistance in locating docket submissions.

II. Final Decision and Order

    OSHA staff examined ITSNA's expansion application, its capability 
to meet the requirements of the test standard, and other pertinent 
information. Based on its review of this evidence, OSHA finds that 
ITSNA meets the requirements of 29 CFR 1910.7 for expansion of its 
recognition, subject to the limitations and conditions listed in this 
notice. OSHA, therefore, is proceeding with this final notice to grant 
ITSNA's expanded scope of recognition. OSHA limits the expansion of 
ITSNA's recognition to testing and certification of products for 
demonstration of conformance to the test standard listed below in table 
1.

[[Page 5939]]



 Table 1--Appropriate Test Standard for Inclusion in ITSNA's NRTL Scope
                             of Recognition
------------------------------------------------------------------------
               Test standard                     Test standard title
------------------------------------------------------------------------
UL 2225...................................  Cables and Cable-Fittings
                                             for Use in Hazardous
                                             (Classified) Locations.
------------------------------------------------------------------------

    OSHA's recognition of any NRTL for a particular test standard is 
limited to equipment or materials for which OSHA standards require 
third-party testing and certification before using them in the 
workplace. Consequently, if a test standard also covers any products 
for which OSHA does not require such testing and certification, a 
NRTL's scope of recognition does not include these products.
    The American National Standards Institute (ANSI) may approve the 
test standards listed above as American National Standards. However, 
for convenience, we may use the designation of the standards-developing 
organization for the standard as opposed to the ANSI designation. Under 
the NRTL Program's policy (see OSHA Instruction CPL 01-00-004, chapter 
2, section VIII), any NRTL recognized for a particular test standard 
may use either the proprietary version of the test standard or the ANSI 
version of that standard. Contact ANSI to determine whether a test 
standard is currently ANSI-approved.

A. Conditions

    Recognition is contingent on continued compliance with 29 CFR 
1910.7, including, but not limited to, abiding by the following 
conditions of the recognition:
    1. ITSNA must inform OSHA as soon as possible, in writing, of any 
change of ownership, facilities, or key personnel, and of any major 
change in its operations as a NRTL, and provide details of the 
change(s);
    2. ITSNA must meet all the terms of its recognition and comply with 
all OSHA policies pertaining to this recognition; and
    3. ITSNA must continue to meet the requirements for recognition, 
including all previously published conditions on ITSNA's scope of 
recognition, in all areas for which it has recognition.
    Pursuant to the authority in 29 CFR 1910.7, OSHA hereby expands the 
scope of recognition of ITSNA as a NRTL, subject to the limitations and 
conditions specified above.

III. Authority and Signature

    James S. Frederick, Deputy Assistant Secretary of Labor for 
Occupational Safety and Health, authorized the preparation of this 
notice. Accordingly, the agency is issuing this notice pursuant to 29 
U.S.C. 657(g)(2), Secretary of Labor's Order No. 8-2020 (85 FR 58393, 
Sept. 18, 2020), and 29 CFR 1910.7.

    Signed at Washington, DC, on January 24, 2024.
James S. Frederick,
Deputy Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2024-01774 Filed 1-29-24; 8:45 am]
BILLING CODE 4510-26-P