[Federal Register Volume 88, Number 207 (Friday, October 27, 2023)]
[Proposed Rules]
[Pages 73772-73775]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-23720]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2023-2135; Project Identifier MCAI-2023-00509-T]
RIN 2120-AA64


Airworthiness Directives; Airbus Canada Limited Partnership (Type 
Certificate Previously Held by C Series Aircraft Limited Partnership 
(CSALP); Bombardier, Inc.) Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus Canada Limited Partnership Model BD-500-1A10 and

[[Page 73773]]

BD-500-1A11 airplanes. This proposed AD was prompted by a report of 
multiple occurrences of low clearance or fouling between certain wiring 
harnesses and a hydraulic bracket and structure in the wing trailing 
edge area that were detected on the production line. This proposed AD 
would require inspecting certain wiring harnesses for any damage and 
clearance to adjacent structure and corrective actions, as specified in 
a Transport Canada AD, which is proposed for incorporation by reference 
(IBR). This proposed AD would also require an inspection report. The 
FAA is proposing this AD to address the unsafe condition on these 
products.

DATES: The FAA must receive comments on this proposed AD by December 
11, 2023.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2023-2135; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For material that is proposed for IBR in this AD, contact 
Transport Canada, Transport Canada National Aircraft Certification, 159 
Cleopatra Drive, Nepean, Ontario K1A 0N5, Canada; telephone 888-663-
3639; email [email protected]. You may find this material on the 
Transport Canada website at tc.canada.ca/en/aviation. It is also 
available at regulations.gov under Docket No. FAA-2023-2135.
     You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Gabriel Kim, Aviation Safety Engineer, 
FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 516-
228-7300; email: [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2023-2135; Project Identifier 
MCAI-2023-00509-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Gabriel Kim, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 
410, Westbury, NY 11590; phone: 516-228-7300; email: [email protected]. Any commentary that the FAA receives which is not 
specifically designated as CBI will be placed in the public docket for 
this rulemaking.

Background

    Transport Canada, which is the aviation authority for Canada, has 
issued Transport Canada AD CF-2023-20, dated March 22, 2023 (Transport 
Canada AD CF-2023-20) (also referred to as the MCAI), to correct an 
unsafe condition for certain Airbus Canada Limited Partnership Model 
BD-500-1A10 and BD-500-1A11 airplanes. The MCAI states that multiple 
occurrences of low clearance or fouling between certain wiring 
harnesses and a hydraulic bracket and structure in the wing trailing 
edge area were detected on the production line. These conditions were 
caused by an inappropriate distribution of slack in the wiring 
harnesses. Low clearance or fouling between the wiring harnesses and 
adjacent structure could result in wear of the harnesses leading to 
electrical arcing. Arcing in the presence of a leak from the hydraulic 
lines in the area could lead to a fire.
    The FAA is proposing this AD to address the unsafe condition on 
these products.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2023-2135.

Related Service Information Under 1 CFR Part 51

    Transport Canada AD CF-2023-20 specifies procedures for inspecting 
certain wiring harnesses for damage and clearance to adjacent structure 
and corrective actions. Corrective actions include adjustment of wiring 
harnesses, replacing damaged braid sleeves, and contacting the 
manufacturer for repair instructions for worn or damaged harnesses. 
This material is reasonably available because the interested parties 
have access to it through their normal course of business or by the 
means identified in ADDRESSES.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this NPRM after determining that 
the unsafe condition described previously is likely to exist or develop 
in other products of the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in Transport Canada AD CF-2023-20 described previously, except for any

[[Page 73774]]

differences identified as exceptions in the regulatory text of this 
proposed AD. This proposed AD would also require an inspection report.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, the 
FAA proposes to incorporate Transport Canada AD CF-2023-20 by reference 
in the FAA final rule. This proposed AD would, therefore, require 
compliance with Transport Canada AD CF-2023-20 in its entirety through 
that incorporation, except for any differences identified as exceptions 
in the regulatory text of this proposed AD. Service information 
required by Transport Canada AD CF-2023-20 for compliance will be 
available at regulations.gov under Docket No. FAA-2023-2135 after the 
FAA final rule is published.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 157 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
               Labor cost                   Parts cost         Cost per product         Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Up to 7 work-hours x $85 per hour = Up               $0   Up to $595................  Up to $93,415.
 to $595.
----------------------------------------------------------------------------------------------------------------

    The FAA has received no definitive data on which to base the cost 
estimates for the on-condition actions specified in this proposed AD.

Paperwork Reduction Act

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to a penalty for 
failure to comply with a collection of information subject to the 
requirements of the Paperwork Reduction Act unless that collection of 
information displays a current valid OMB Control Number. The OMB 
Control Number for this information collection is 2120-0056. Public 
reporting for this collection of information is estimated to take 
approximately 1 hour per response, including the time for reviewing 
instructions, searching existing data sources, gathering and 
maintaining the data needed, and completing and reviewing the 
collection of information. All responses to this collection of 
information are mandatory. Send comments regarding this burden estimate 
or any other aspect of this collection of information, including 
suggestions for reducing this burden, to: Information Collection 
Clearance Officer, Federal Aviation Administration, 10101 Hillwood 
Parkway, Fort Worth, TX 76177-1524.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Airbus Canada Limited Partnership (Type Certificate Previously Held 
by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.): 
Docket No. FAA-2023-2135; Project Identifier MCAI-2023-00509-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by December 11, 2023.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus Canada Limited Partnership (Type 
Certificate previously held by C Series Aircraft Limited Partnership 
(CSALP); Bombardier, Inc.) Model BD-500-1A10 and BD-500-1A11 
airplanes, certificated in any category, as identified in Transport 
Canada AD CF-2023-20, dated March 22, 2023 (Transport Canada AD CF-
2023-20).

(d) Subject

    Air Transport Association (ATA) of America Code 24, Electrical 
Power.

(e) Unsafe Condition

    This AD was prompted by a report of multiple occurrences of low 
clearance or fouling between certain wiring harnesses and a 
hydraulic bracket and structure in the wing trailing edge area that 
were detected on the production line. The FAA is issuing this AD to 
address inappropriate distribution of slack in the wiring harness. 
The unsafe condition, if not addressed, could result in wear of the

[[Page 73775]]

harnesses leading to electrical arcing. Arcing in the presence of a 
leak from the hydraulic lines in the area could lead to a fire.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, Transport Canada AD CF-2023-20.

(h) Exceptions to Transport Canada AD CF-2023-20

    (1) Where Transport Canada AD CF-2023-20 refers to its effective 
date, this AD requires using the effective date of this AD.
    (2) Where Transport Canada AD CF-2023-20 refers to hours air 
time, this AD requires using flight hours.
    (3) Where paragraph (A) of Transport Canada AD CF-2023-20 states 
to ``adjust as required,'' this AD requires that all applicable 
adjustments must be done before further flight.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the International 
Validation Branch, send it to the attention of the person identified 
in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or Transport Canada; or Airbus Canada 
Limited Partnership's Transport Canada Design Approval Organization 
(DAO). If approved by the DAO, the approval must include the DAO-
authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (i)(2) of this AD, if any service information contains 
procedures that are identified as RC, those procedures must be done 
to comply with this AD; any procedures that are not identified as RC 
are recommended. Those procedures that are not identified as RC may 
be deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the procedures identified as RC can be 
done and the airplane can be put back in an airworthy condition. Any 
substitutions or changes to procedures identified as RC require 
approval of an AMOC.

(j) Additional Information

    For more information about this AD, contact Gabriel Kim, 
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; phone: 516-228-7300; email: [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Transport Canada AD CF-2023-20, dated March 22, 2023.
    (ii) [Reserved]
    (3) For Transport Canada AD CF-2023-20, contact Transport 
Canada, Transport Canada National Aircraft Certification, 159 
Cleopatra Drive, Nepean, Ontario K1A 0N5, Canada; telephone 888-663-
3639; email [email protected]. You may find this Transport 
Canada AD on the Transport Canada website at tc.canada.ca/en/
aviation.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on October 20, 2023.
Ross Landes,
Deputy Director for Regulatory Operations, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2023-23720 Filed 10-26-23; 8:45 am]
BILLING CODE 4910-13-P