[Federal Register Volume 88, Number 103 (Tuesday, May 30, 2023)]
[Notices]
[Pages 34547-34548]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-11422]
-----------------------------------------------------------------------
DEPARTMENT OF LABOR
Mine Safety and Health Administration
Petition for Modification of Application of Existing Mandatory
Safety Standard
AGENCY: Mine Safety and Health Administration, Labor.
ACTION: Notice.
-----------------------------------------------------------------------
SUMMARY: This notice is a summary of a petition for modification
submitted to the Mine Safety and Health Administration (MSHA) by the
party listed below.
DATES: All comments on the petition must be received by MSHA's Office
of Standards, Regulations, and Variances on or before June 29, 2023.
ADDRESSES: You may submit comments identified by Docket No. MSHA-2023-
0014 by any of the following methods:
1. Federal eRulemaking Portal: https://www.regulations.gov. Follow
the instructions for submitting comments for MSHA-2023-0026.
2. Fax: 202-693-9441.
3. Email: [email protected].
4. Regular Mail or Hand Delivery: MSHA, Office of Standards,
Regulations, and Variances, 201 12th Street South, Suite 4E401,
Arlington, Virginia 22202-5452.
Attention: S. Aromie Noe, Director, Office of Standards,
Regulations, and Variances. Persons delivering documents are required
to check in at the receptionist's desk in Suite 4E401. Individuals may
inspect copies of the petition and comments during normal business
hours at the address listed above. Before visiting MSHA in person, call
202-693-9455 to make an appointment, in keeping with the Department of
Labor's COVID-19 policy. Special health precautions may be required.
FOR FURTHER INFORMATION CONTACT: S. Aromie Noe, Office of Standards,
Regulations, and Variances at 202-693-9440 (voice),
[email protected] (email), or 202-693-9441 (fax). [These
are not toll-free numbers.]
SUPPLEMENTARY INFORMATION: Section 101(c) of the Federal Mine Safety
and Health Act of 1977 and title 30 of the Code of Federal Regulations
(CFR) part 44 govern the application, processing, and disposition of
petitions for modification.
I. Background
Section 101(c) of the Federal Mine Safety and Health Act of 1977
(Mine Act) allows the mine operator or representative of miners to file
a petition to modify the application of any mandatory safety standard
to a coal or other mine if the Secretary of Labor determines that:
1. An alternative method of achieving the result of such standard
exists which will at all times guarantee no less than the same measure
of protection afforded the miners of such mine by such standard; or
2. The application of such standard to such mine will result in a
diminution of safety to the miners in such mine.
In addition, sections 44.10 and 44.11 of 30 CFR establish the
requirements for filing petitions for modification.
II. Petition for Modification
Docket Number: M-2023-002-M.
Petitioner: U.S. Silica Company, 4800 Oklahoma Hwy 1 North, Mill
Creek, Oklahoma 74856.
Mine: Mill Creek Plant #37, MSHA ID No. 34-00377, located in
Johnston County, Oklahoma.
Regulation Affected: 30 CFR 56.13020 (Use of compressed air).
Modification Request: The petitioner requests a modification of 30
CFR 56.13020 to allow compressed air to be directed towards persons for
use in a clothes cleaning booth.
The petitioner states that:
(a) The petitioner proposes to implement a clothes cleaning
process.
(b) The alternative method provides a direct reduction of a miners'
exposures to respirable dust, thus reducing their health risks.
(c) The proposed alternative method has been developed jointly
between Unimin Corporation and the National Institute for Occupational
Safety and Health (NIOSH) and has been successfully tested by NIOSH.
The petitioner proposes the following alternative method:
(a) The petitioner will use a clothes cleaning booth, CCB Elite I,
serial number 5406, manufactured by S.K. Bowling, Inc.
(b) Only miners trained in the operation of the clothes cleaning
booth (booth) will be permitted to use the booth to clean their
clothes.
(c) The petitioner will incorporate the NIOSH Clothes Cleaning
Process and
[[Page 34548]]
manufacturer's instruction manuals into their MSHA part 46 training
plan and train affected miners in the process.
(d) Miners entering the booth shall examine valves and nozzles for
damage or malfunction and will close the door fully before opening the
air valve. Any defects shall be repaired prior to the booth being used.
(e) Miners entering the booth shall wear eye protection, ear plugs
or muffs for hearing protection, and respiratory protection meaning a
full-face or half-mask respirator that meets or exceeds the minimum
requirements of an N95 filter to which the miner has been fit-tested.
As an alternative, the use of a full-face respirator will also meet the
requirement for eye protection. A sign will be conspicuously posted
that states the above personal protective equipment is required when
entering the booth.
(f) Air flow through the booth will be at least 2,000 cubic feet
per minute (cfm) to maintain negative pressure during the use of the
cleaning system in order to prevent contamination of the environment
outside the booth. Airflow will be in a downward direction, thereby
moving contaminants away from the miner's breathing zone.
(g) Air pressure through the spray manifold will be limited to 30
pounds per square inch or less. A lock box with a single, plant
manager-controlled key will be used to prevent regulator tampering.
(h) The spray manifold will consist of a 2-inch square tube with
\1/4\ inch wall thickness, capped at the base and actuated by an
electrically controlled valve at the top.
(i) Air nozzles shall not exceed 30 pound(s) per square inch gauge.
(j) The uppermost spray of the spray manifold will be located below
the booth user's breathing zone. Some type of mechanical device can be
used to cover the upper air nozzles to meet the specific height of the
user.
(k) Air nozzles shall be guarded to eliminate the possibility of
incidental contact, which could create mechanical damage to the air
nozzles during the clothes cleaning process.
(l) The petitioner shall conduct periodic maintenance checks of the
booth in accordance with the recommendations contained in the
manufacturer's instruction manual.
(m) The air receiver tank supplying air to the manifold system will
be of sufficient volume to permit no less than 20 seconds of continuous
cleaning time.
(n) An appropriate hazard warning sign will be posted on the booth
to state, at a minimum, ``Compressed Air'' and ``Respirable Dust.''
(o) A pressure relief valve designed for the booth's air reservoir
will be installed.
(p) The mine will exhaust dust-laden air from the booth into a
local exhaust ventilation system or duct outside the facility while
ensuring there is no re-entrainment back into the structure.
In support of the proposed alternative method, the petitioner
submitted specifications of the dust booth; installation and operating
instructions of the dust booth to be used; and The Dust Control
Handbook for Industrial Minerals, Mining, and Processing.
The petitioner asserts that the alternate method proposed will at
all times guarantee no less than the same measure of protection
afforded the miners under the mandatory standard.
Song-ae Aromie Noe,
Director, Office of Standards, Regulations, and Variances.
[FR Doc. 2023-11422 Filed 5-26-23; 8:45 am]
BILLING CODE 4520-43-P