[Federal Register Volume 88, Number 37 (Friday, February 24, 2023)]
[Proposed Rules]
[Pages 11825-11827]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-03623]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2023-0170; Project Identifier MCAI-2022-00974-T]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc., Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Bombardier, Inc., Model BD-700-2A12 airplanes. This 
proposed AD was prompted by a report that certain environmental control 
system (ECS) pre-cooler clamp assemblies may not conform to 
specifications. This proposed AD would require an inspection of the 
pre-cooler clamps and replacement of non-conforming pre-cooler clamps. 
The FAA is proposing this AD to address the unsafe condition on these 
products.

DATES: The FAA must receive comments on this proposed AD by April 10, 
2023.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2023-0170; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For service information identified in this NPRM, contact 
Bombardier Business Aircraft Customer Response Center, 400 C[ocirc]te-
Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, Canada; telephone 514-
855-2999; email bombardier.com">ac.yul@aero.bombardier.com; website bombardier.com.
     You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195.

FOR FURTHER INFORMATION CONTACT: Elizabeth Dowling, Aerospace Engineer, 
Mechanical Systems and Administrative Services Section, FAA, New York 
ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone 516-228-7300; email [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No.

[[Page 11826]]

FAA-2023-0170; Project Identifier MCAI-2022-00974-T'' at the beginning 
of your comments. The most helpful comments reference a specific 
portion of the proposal, explain the reason for any recommended change, 
and include supporting data. The FAA will consider all comments 
received by the closing date and may amend the proposal because of 
those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Elizabeth Dowling, Aerospace Engineer, Mechanical Systems and 
Administrative Services Section, FAA, New York ACO Branch, 1600 Stewart 
Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300; email [email protected]. Any commentary that the FAA receives which is 
not specifically designated as CBI will be placed in the public docket 
for this rulemaking.

Background

    Transport Canada, which is the aviation authority for Canada, has 
issued Transport Canada AD CF-2022-39, dated July 18, 2022 (Transport 
Canada AD CF-2022-39) (also referred to after this as the MCAI), to 
correct an unsafe condition on certain Bombardier, Inc., Model BD-700-
2A12 airplanes. The MCAI states that a disclosure letter from the 
supplier advised that certain pre-cooler clamp assemblies securing the 
ducting connection on the ECS pre-cooler inlet assembly may not conform 
to drawing. If left uncorrected, the clamp may fail and cause excessive 
leakage at that connection. This could lead to increased operating 
temperatures in climate-controlled zones, or, in combination with other 
failures, a complete loss of the ECS.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2023-0170.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Bombardier Service Bulletin 700-36-7504, dated 
June 27, 2022. This service information specifies procedures for 
inspecting the pre-cooler clamps for non-conformance to the drawing and 
replacing non-conforming pre-cooler clamps. The clamp replacement 
includes a general visual inspection of non-conforming pre-cooler 
clamps around the silicone bellow for signs of damage, and corrective 
action including repair. This service information is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in the 
ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with this State of Design Authority, 
it has notified the FAA of the unsafe condition described in the MCAI 
and service information described above. The FAA is issuing this NPRM 
after determining that the unsafe condition described previously is 
likely to exist or develop on other products of the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in the service information already described.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 12 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                   Cost per
                  Labor cost                      Parts cost        product          Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
2 work-hours x $85 per hour = $170............             $60            $230  Up to $2,760.
----------------------------------------------------------------------------------------------------------------

    The FAA has received no definitive data on which to base the cost 
estimates for the on-condition repairs specified in this proposed AD.
    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this proposed AD may be covered under warranty, thereby reducing the 
cost impact on affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:

[[Page 11827]]

    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Bombardier, Inc.: Docket No. FAA-2023-0170; Project Identifier MCAI-
2022-00974-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by April 10, 2023.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc., Model BD-700-2A12 
airplanes, certificated in any category, serial numbers 70032, 70047 
through 70056 inclusive, 70058 through 70061 inclusive, and 70063 
through 70075 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 36, Pneumatic.

(e) Unsafe Condition

    This AD was prompted by a report that certain environmental 
control system (ECS) pre-cooler clamp assemblies may not conform to 
specifications. The FAA is issuing this AD to address possible 
excessive leakage caused by clamp failure. The unsafe condition, if 
not addressed, could result in increased operating temperatures in 
climate-controlled zones, or, in combination with other failures, a 
complete loss of the ECS.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Within 36 months after the effective date of this AD: Identify 
and replace, as applicable, the ECS pre-cooler clamps in accordance 
with the Accomplishment Instructions of Bombardier Service Bulletin 
700-36-7504, dated June 27, 2022.

(h) No Reporting Requirement

    Although Bombardier Service Bulletin 700-36-7504, dated June 27, 
2022, specifies to submit certain information to the manufacturer or 
discard affected clamps, this AD does not include that requirement.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York ACO Branch, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or responsible Flight Standards Office, as appropriate. If 
sending information directly to the manager of the New York ACO 
Branch, mail it to ATTN: Program Manager, Continuing Operational 
Safety, at the address identified in paragraph (j)(2) of this AD or 
email to: [email protected]. If mailing information, also 
submit information by email. Before using any approved AMOC, notify 
your appropriate principal inspector, or lacking a principal 
inspector, the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, New York ACO 
Branch, FAA; or Transport Canada Civil Aviation (TCCA); or 
Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If 
approved by the DAO, the approval must include the DAO-authorized 
signature.

(j) Additional Information

    (1) Refer to Transport Canada AD CF-2022-39, dated July 18, 
2022, for related information. This Transport Canada AD may be found 
in the AD docket at regulations.gov under Docket No. FAA-2023-0170.
    (2) For more information about this AD, contact Elizabeth 
Dowling, Aerospace Engineer, Mechanical Systems and Administrative 
Services Section, FAA, New York ACO Branch, 1600 Stewart Avenue, 
Suite 410, Westbury, NY 11590; telephone 516-228-7300; email [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) Bombardier Service Bulletin 700-36-7504, dated June 27, 
2022.
    (ii) [Reserved]
    (3) For service information identified in this AD, contact 
Bombardier Business Aircraft Customer Response Center, 400 
C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, Canada; 
telephone 514-855-2999; email bombardier.com">ac.yul@aero.bombardier.com; website 
bombardier.com.
    (4) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, email [email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on February 15, 2023.
Christina Underwood, Acting Director,
Compliance & Airworthiness Division, Aircraft Certification Service.
[FR Doc. 2023-03623 Filed 2-23-23; 8:45 am]
BILLING CODE 4910-13-P