[Federal Register Volume 88, Number 10 (Tuesday, January 17, 2023)]
[Notices]
[Pages 2641-2642]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-00676]


-----------------------------------------------------------------------

DEPARTMENT OF LABOR

Occupational Safety and Health Administration

[Docket No. OSHA-2006-0028]


Eurofins Electrical and Electronic Testing NA, Inc. a/k/a MET 
Laboratories, Inc.: Grant of Expansion of Recognition

AGENCY: Occupational Safety and Health Administration (OSHA), Labor.

ACTION: Notice.

-----------------------------------------------------------------------

SUMMARY: In this notice, OSHA announces the final decision to expand 
the scope of recognition for Eurofins Electronic Testing NA, Inc. a/k/a 
MET Laboratories, Inc., as a Nationally Recognized Testing Laboratory 
(NRTL).

DATES: The expansion of the scope of recognition becomes effective on 
January 17, 2023.

FOR FURTHER INFORMATION CONTACT: Information regarding this notice is 
available from the following sources:
    Press inquiries: Contact Mr. Frank Meilinger, Director, OSHA Office 
of Communications; telephone: (202) 693-1999; email: 
[email protected].
    General and technical information: Contact Mr. Kevin Robinson, 
Director, Office of Technical Programs and Coordination Activities, 
Directorate of Technical Support and Emergency Management, Occupational 
Safety and Health Administration; telephone: (202) 693-2110; email: 
[email protected]. OSHA's web page includes information about the 
NRTL Program (see http://www.osha.gov/dts/otpca/nrtl/index.html).

SUPPLEMENTARY INFORMATION:

I. Notice of Final Decision

    OSHA hereby gives notice of the expansion of the scope of 
recognition of Eurofins Electrical and Electronic Testing NA, Inc. a/k/
a MET Laboratories, Inc. (MET), as a NRTL. MET's expansion covers the 
addition of two test standards to the NRTL scope of recognition.
    OSHA recognition of a NRTL signifies that the organization meets 
the requirements specified by 29 CFR 1910.7. Recognition is an

[[Page 2642]]

acknowledgment that the organization can perform independent safety 
testing and certification of the specific products covered within the 
scope of recognition and is not a delegation or grant of government 
authority. As a result of recognition, employers may use products 
properly approved by the NRTL to meet OSHA standards that require 
testing and certification of the products.
    The agency processes applications by a NRTL for initial 
recognition, or for expansion or renewal of this recognition, following 
requirements in Appendix A to 29 CFR 1910.7. This appendix requires 
that the agency publish two notices in the Federal Register in 
processing an application. In the first notice, OSHA announces the 
application and provides the preliminary finding, and in the second 
notice, the agency provides the final decision on the application. 
These notices set forth the NRTL's scope of recognition or 
modifications of that scope. OSHA maintains an informational web page 
for each NRTL that details the scope of recognition. These pages are 
available from the agency's website at http://www.osha.gov/dts/otpca/nrtl/index.html.
    MET submitted an application, dated September 3, 2021 (OSHA-2006-
0028-0092), to expand the recognition to include two additional test 
standards. OSHA staff performed a detailed analysis of the application 
packet and reviewed other pertinent information. OSHA did not perform 
any on-site reviews in relation to the application.
    OSHA published the preliminary notice announcing MET's expansion 
application in the Federal Register on November 23, 2022 (87 FR 71684). 
The agency requested comments by December 8, 2022, but it received no 
comments in response to this notice. OSHA now is proceeding with this 
final notice to grant expansion of MET's scope of recognition.
    To obtain or review copies of all public documents pertaining to 
MET's application, go to http://www.regulations.gov or contact the OSHA 
Docket Office. Docket No. OSHA-2006-0028 contains all materials in the 
record concerning MET's recognition. Please note: Due to the COVID-19 
pandemic, the Docket Office is closed to the public at this time but 
can be contacted at (202) 693-2350 (TTY ((877) 889-5627).

II. Final Decision and Order

    OSHA staff examined MET's expansion application, the capability to 
meet the requirements of the test standard, and other pertinent 
information. Based on the review of this evidence, OSHA finds that MET 
meets the requirements of 29 CFR 1910.7 for expansion of the NRTL scope 
of recognition, subject to the limitation and conditions listed below. 
OSHA, therefore, is proceeding with this final notice to grant MET's 
scope of recognition. OSHA limits the expansion of MET's recognition to 
testing and certification of products for demonstration of conformance 
to the test standards listed in Table 1.

 Table 1--List of Appropriate Test Standards for Inclusion in MET's NRTL
                          Scope of Recognition
------------------------------------------------------------------------
        Test Standard                     Test standard title
------------------------------------------------------------------------
UL 698A......................  Standard for Industrial Control Panels
                                Related to Hazardous (Classified)
                                Locations
UL 60079-31..................  Standard for Safety Explosive
                                Atmospheres--Part 31: Equipment Dust
                                Ignition Protection by Enclosure ``t''
------------------------------------------------------------------------

    OSHA's recognition of any NRTL for a particular test standard is 
limited to equipment or materials for which OSHA standards require 
third-party testing and certification before using them in the 
workplace. Consequently, if a test standard also covers any products 
for which OSHA does not require such testing and certification, a 
NRTL's scope of recognition does not include these products.
    The American National Standards Institute (ANSI) may approve the 
test standards listed above as American National Standards. However, 
for convenience, the use of the designation of the standards-developing 
organization for the standard as opposed to the ANSI designation may 
occur. Under the NRTL Program's policy (see OSHA Instruction CPL 01-00-
004, Chapter 2, Section VIII), only standards determined to be 
appropriate test standards may be approved for NRTL recognition. Any 
NRTL recognized for a particular test standard may use either the 
proprietary version of the test standard or the ANSI version of that 
standard. Contact ANSI to determine whether a test standard is 
currently ANSI-approved.

A. Conditions

    In addition to those conditions already required by 29 CFR 1910.7, 
MET must abide by the following conditions of the recognition:
    1. MET must inform OSHA as soon as possible, in writing, of any 
change of ownership, facilities, or key personnel, and of any major 
change in their operations as a NRTL, and provide details of the 
change(s);
    2. MET must meet all the terms of the NRTL recognition and comply 
with all OSHA policies pertaining to this recognition; and
    3. MET must continue to meet the requirements for recognition, 
including all previously published conditions on MET's scope of 
recognition, in all areas for which it has recognition.
    Pursuant to the authority in 29 CFR 1910.7, OSHA hereby expands the 
scope of recognition of MET, subject to the limitations and conditions 
specified above.

III. Authority and Signature

    James S. Frederick, Deputy Assistant Secretary of Labor for 
Occupational Safety and Health, authorized the preparation of this 
notice. Accordingly, the agency is issuing this notice pursuant to 29 
U.S.C. 657(g)(2), Secretary of Labor's Order No. 8-2020 (85 FR 58393, 
Sept. 18, 2020)), and 29 CFR 1910.7.

    Signed at Washington, DC, on January 10, 2023.
James S. Frederick,
Deputy Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2023-00676 Filed 1-13-23; 8:45 am]
BILLING CODE 4510-26-P