[Federal Register Volume 87, Number 249 (Thursday, December 29, 2022)]
[Rules and Regulations]
[Pages 80026-80027]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-28271]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-1248; Project Identifier MCAI-2022-00609-T; 
Amendment 39-22286; AD 2022-27-01]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Airbus SAS Model A350-941 and -1041 airplanes. This AD is 
prompted by a report that during flight and fatigue testing it was 
detected that some fasteners installed in the center wing box (CWB) 
rotated inside their fastener holes. This AD requires replacing 
affected fasteners and applying additional head nut cap protection at 
the front and rear spars in the CWB, as specified in a European Union 
Aviation Safety Agency (EASA) AD, which is incorporated by reference. 
The FAA is issuing this AD to address the unsafe condition on these 
products.

DATES: This AD is effective February 2, 2023.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of February 2, 
2023.

ADDRESSES: 
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2022-1248; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this final rule, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
address for Docket Operations is U.S. Department of Transportation, 
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 
New Jersey Avenue SE, Washington, DC 20590.
    Material Incorporated by Reference:
     For material incorporated by reference in this AD, contact 
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; website easa.europa.eu. You may 
find this EASA AD on the EASA website at ad.easa.europa.eu.
     You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195. It is also available at regulations.gov under 
Docket No. FAA-2022-1248.

FOR FURTHER INFORMATION CONTACT: Dat Le, Aerospace Engineer, Large 
Aircraft Section, FAA, International Validation Branch, 2200 South 
216th St., Des Moines, WA 98198; telephone 516-228-7317; email 
[email protected].

SUPPLEMENTARY INFORMATION: 

Background

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to certain Airbus SAS 
Model A350-941 and -1041 airplanes. The NPRM published in the Federal 
Register on October 20, 2022 (87 FR 63709). The NPRM was prompted by AD 
2022-0080, dated May 9, 2022, issued by EASA, which is the Technical 
Agent for the Member States of the European Union (EASA AD 2022-0080) 
(referred to after this as the MCAI). The MCAI states that during 
flight and fatigue testing it was detected that some fasteners 
installed in the CWB rotated inside their fastener holes. Investigation 
revealed there was insufficient friction for the application.
    In the NPRM, the FAA proposed to require replacing affected 
fasteners and applying additional head nut cap protection at the front 
and rear spars in the CWB, as specified in EASA AD 2022-0080. The FAA 
is issuing this AD to address fasteners installed in the CWB rotating 
inside their fastener holes, which if not corrected, could lead to loss 
of a fastener clamping and cracking of the nut sealant cover, possibly 
resulting, in case of lightning strike, in a fuel tank explosion and 
consequent loss of the airplane.
    You may examine the MCAI in the AD docket at regulations.gov under 
Docket No. FAA-2022-1248.

Discussion of Final Airworthiness Directive Comments

    The FAA received a comment from the Air Line Pilots Association, 
International (ALPA) who supported the NPRM without change.

Conclusion

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
referenced above. The FAA reviewed the relevant data, considered the 
comment received, and determined that air safety requires adopting this 
AD as proposed. Accordingly, the FAA is issuing this AD to address the 
unsafe condition on this product. This AD is adopted as proposed in the 
NPRM.

Related Service Information Under 1 CFR Part 51

    EASA AD 2022-0080 specifies procedures for replacing affected 
fasteners installed on the left-hand and right-hand CWB at the front 
and rear spar areas and for adding head nut cap protection at the front 
and rear spars in the CWB. This material is reasonably available 
because the interested parties have access to it through their normal 
course of business or by the means identified in ADDRESSES.

Costs of Compliance

    The FAA estimates that this AD affects 30 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
83 work-hours x $85 per hour = $7,055........................          $7,500          $14,555         $436,650
----------------------------------------------------------------------------------------------------------------

    The FAA has included all known costs in its cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this AD may be covered under warranty, thereby reducing the cost impact 
on affected operators.

[[Page 80027]]

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2022-27-01 Airbus SAS: Amendment 39-22286; Docket No. FAA-2022-1248; 
Project Identifier MCAI-2022-00609-T.

(a) Effective Date

    This airworthiness directive (AD) is effective February 2, 2023.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS Model A350-941 and -1041 
airplanes, certificated in any category, as identified in European 
Union Aviation Safety Agency (EASA) AD 2022-0080, dated May 9, 2022 
(EASA AD 2022-0080).

(d) Subject

    Air Transport Association (ATA) of America Code 57, Wings.

(e) Unsafe Condition

    This AD was prompted by a report that during flight and fatigue 
testing it was detected that some fasteners installed in the center 
wing box (CWB) rotated inside their fastener holes. The FAA is 
issuing this AD to address fasteners installed in the CWB rotating 
inside their fastener holes, which if not corrected, could lead to 
loss of a fastener clamping and cracking of the nut sealant cover, 
possibly resulting, in case of lightning strike, in a fuel tank 
explosion and consequent loss of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2022-0080.

(h) Exceptions to EASA AD 2022-0080

    (1) Where EASA AD 2022-0080 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2022-0080 does not apply 
to this AD.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the International 
Validation Branch, send it to the attention of the person identified 
in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (i)(2) of this AD, if any service information contains 
procedures or tests that are identified as RC, those procedures and 
tests must be done to comply with this AD; any procedures or tests 
that are not identified as RC are recommended. Those procedures and 
tests that are not identified as RC may be deviated from using 
accepted methods in accordance with the operator's maintenance or 
inspection program without obtaining approval of an AMOC, provided 
the procedures and tests identified as RC can be done and the 
airplane can be put back in an airworthy condition. Any 
substitutions or changes to procedures or tests identified as RC 
require approval of an AMOC.

(j) Additional Information

    For more information about this AD, contact Dat Le, Aerospace 
Engineer, Large Aircraft Section, FAA, International Validation 
Branch, 2200 South 216th St., Des Moines, WA 98198; telephone 516-
228-7317; email [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the service information listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2022-0080, 
dated May 9, 2022.
    (ii) [Reserved]
    (3) For EASA AD 2022-0080, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; website easa.europa.eu. You may find this EASA 
AD on the EASA website at ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on December 20, 2022.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2022-28271 Filed 12-28-22; 8:45 am]
BILLING CODE 4910-13-P