[Federal Register Volume 87, Number 238 (Tuesday, December 13, 2022)]
[Proposed Rules]
[Pages 76160-76162]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-26975]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-1580; Project Identifier MCAI-2022-00808-T]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus SAS Model A350-941 and -1041 airplanes. This 
proposed AD was prompted by a determination that the surface protection 
is missing between certain aluminum brackets and the struts to which 
they are attached in the flight deck air distribution system. This 
proposed AD would require applying surface protection to the affected 
aluminum brackets and struts, as specified in a European Union Aviation 
Safety Agency (EASA) AD, which is proposed for incorporation by 
reference (IBR). This proposed AD would also prohibit modifying an 
airplane using certain service information. The FAA is proposing this 
AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by January 27, 
2023.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    AD Docket: You may examine the AD docket at regulations.gov under 
Docket No. FAA-2022-1580; or in person at Docket Operations between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains this NPRM, the mandatory continuing airworthiness 
information (MCAI), any comments received, and other information. The 
street address for Docket Operations is listed above.
    Material Incorporated by Reference:
     For material that is proposed for IBR in this NPRM, 
contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone 
+49 221 8999 000; email [email protected]; website easa.europa.eu. You 
may find this material on the EASA website at ad.easa.europa.eu.
     You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195. It is also available in the AD docket at 
regulations.gov under Docket No. FAA-2022-1580.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, Large 
Aircraft Section, FAA, International Validation Branch, 2200 South 
216th St., Des Moines, WA 98198; telephone 206-231-3225; email 
[email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2022-1580; Project Identifier 
MCAI-2022-00808-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as

[[Page 76161]]

private, and that is relevant or responsive to this NPRM, it is 
important that you clearly designate the submitted comments as CBI. 
Please mark each page of your submission containing CBI as ``PROPIN.'' 
The FAA will treat such marked submissions as confidential under the 
FOIA, and they will not be placed in the public docket of this NPRM. 
Submissions containing CBI should be sent to Dan Rodina, Aerospace 
Engineer, Large Aircraft Section, FAA, International Validation Branch, 
2200 South 216th St., Des Moines, WA 98198; telephone 206-231-3225; 
email [email protected]. Any commentary that the FAA receives which is 
not specifically designated as CBI will be placed in the public docket 
for this rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2022-0119, dated June 21, 2022 (EASA 
AD 2022-0119) (also referred to as the MCAI), to correct an unsafe 
condition for certain Airbus SAS Model A350-941 and -1041 airplanes.
    This proposed AD was prompted by a determination that the surface 
protection is missing between certain aluminum brackets and the struts 
to which they are attached in the flight deck air distribution system. 
The affected parts were installed either in production through Airbus 
modification 109229 or 109230, or in-service through accomplishing the 
original issue of Airbus Service Bulletin A350-21-P031; or the original 
issue of Airbus Service Bulletin A350-21-P032. The FAA is proposing 
this AD to address missing aluminum bracket surface protection. This 
condition, if not corrected, could lead to rupture of the associated 
ducting, reducing the efficiency of the flight deck air distribution 
system, which, in combination with smoke in the flight deck, could 
result in impaired flightcrew capability to control the airplane. See 
the MCAI for additional background information.

Related Service Information Under 1 CFR Part 51

    EASA AD 2022-0119 specifies procedures for applying surface 
protection to aluminum brackets and struts at frame (FR) 22 and FR 24, 
as applicable, in zone C2-2 forward section. EASA AD 2020-0119 also 
prohibits modifying an airplane using certain service information. This 
material is reasonably available because the interested parties have 
access to it through their normal course of business or by the means 
identified in the ADDRESSES section.

FAA's Determination

    These products have been approved by the aviation authority of 
another country and are approved for operation in the United States. 
Pursuant to the FAA's bilateral agreement with the State of Design 
Authority, it has notified the FAA of the unsafe condition described in 
the MCAI referenced above. The FAA is issuing this NPRM after 
determining that the unsafe condition described previously is likely to 
exist or develop in other products of the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2022-0119 described previously, except for any differences 
identified as exceptions in the regulatory text of this proposed AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, the 
FAA proposes to incorporate EASA AD 2022-0119 by reference in the FAA 
final rule. This proposed AD would, therefore, require compliance with 
EASA AD 2022-0119 in its entirety through that incorporation, except 
for any differences identified as exceptions in the regulatory text of 
this proposed AD. Using common terms that are the same as the heading 
of a particular section in EASA AD 2022-0119 does not mean that 
operators need comply only with that section. For example, where the AD 
requirement refers to ``all required actions and compliance times,'' 
compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2022-
0119. Service information required by EASA AD 2022-0119 for compliance 
will be available at regulations.gov by searching for and locating 
Docket No. FAA-2022-1580 after the FAA final rule is published.

Costs of Compliance

    The FAA estimates that this proposed AD would affect 30 airplanes 
of U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
8 work-hours x $85 per hour = $680...........................          $1,350           $2,030          $60,900
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:

[[Page 76162]]

    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Airbus SAS: Docket No. FAA-2022-1580; Project Identifier MCAI-2022-
00808-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by January 27, 2023.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS Model A350-941 and -1041 
airplanes, certificated in any category, as identified in European 
Union Aviation Safety Agency (EASA) AD 2022-0119, dated June 21, 
2022 (EASA AD 2022-0119).

(d) Subject

    Air Transport Association (ATA) of America Code 21, Air 
conditioning.

(e) Unsafe Condition

    This AD was prompted by a determination that the surface 
protection is missing between certain aluminum brackets and the 
struts to which they are attached in the flight deck air 
distribution system. The FAA is issuing this AD to address missing 
aluminum bracket surface protection. This condition, if not 
corrected, could lead to rupture of the associated ducting, reducing 
the efficiency of the flight deck air distribution system, which, in 
combination with smoke in the flight deck, could result in impaired 
flightcrew capability to control the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2022-0119.

(h) Exceptions to EASA AD 2022-0119

    (1) Where EASA AD 2022-0119 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2022-0119 does not apply 
to this AD.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Validation Branch, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or responsible Flight Standards Office, as 
appropriate. If sending information directly to the International 
Validation Branch, send it to the attention of the person identified 
in paragraph (j) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design 
Organization Approval (DOA). If approved by the DOA, the approval 
must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (i)(2) of this AD, if any service information contains 
procedures or tests that are identified as RC, those procedures and 
tests must be done to comply with this AD; any procedures or tests 
that are not identified as RC are recommended. Those procedures and 
tests that are not identified as RC may be deviated from using 
accepted methods in accordance with the operator's maintenance or 
inspection program without obtaining approval of an AMOC, provided 
the procedures and tests identified as RC can be done and the 
airplane can be put back in an airworthy condition. Any 
substitutions or changes to procedures or tests identified as RC 
require approval of an AMOC.

(j) Related Information

    For more information about this AD, contact Dan Rodina, 
Aerospace Engineer, Large Aircraft Section, FAA, International 
Validation Branch, 2200 South 216th St., Des Moines, WA 98198; 
telephone 206-231-3225; email [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2022-0119, 
dated June 21, 2022.
    (ii) [Reserved]
    (3) For EASA AD 2022-0119, contact EASA, Konrad-Adenauer-Ufer 3, 
50668 Cologne, Germany; telephone +49 221 8999 000; email 
[email protected]; website easa.europa.eu. You may find this EASA 
AD on the EASA website at ad.easa.europa.eu.
    (4) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, email [email protected], or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on December 7, 2022.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2022-26975 Filed 12-12-22; 8:45 am]
BILLING CODE 4910-13-P