[Federal Register Volume 87, Number 170 (Friday, September 2, 2022)]
[Rules and Regulations]
[Pages 54131-54134]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-19116]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2022-1067; Project Identifier MCAI-2022-01042-T; 
Amendment 39-22169; AD 2022-18-18]
RIN 2120-AA64


Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
Dassault Aviation Model FALCON 7X airplanes. This AD was prompted by a 
report of a failed extension of inboard slats during the landing phase, 
which was not indicated to the flightcrew by the crew alerting system. 
This AD requires revising the existing airplane flight manual (AFM) to 
provide procedures for failed extension of inboard slats and flightcrew 
indication during landing, as specified in a European Union Aviation 
Safety Agency (EASA) AD, which is incorporated by reference. The FAA is 
issuing this AD to address the unsafe condition on these products.

DATES: This AD becomes effective September 19, 2022.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of September 
19, 2022.
    The FAA must receive comments on this AD by October 17, 2022.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to regulations.gov. Follow 
the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For material incorporated by reference (IBR) in this AD, contact 
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; internet easa.europa.eu. You may 
find this IBR material on the EASA website at ad.easa.europa.eu. You 
may view this material at the FAA, Airworthiness Products Section, 
Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 206-
231-3195. It is also available in the AD docket at regulations.gov by 
searching for and locating Docket No. FAA-2022-1067.

[[Page 54132]]

Examining the AD Docket

    You may examine the AD docket at regulations.gov by searching for 
and locating Docket No. FAA-2022-1067; or in person at Docket 
Operations between 9 a.m. and 5 p.m., Monday through Friday, except 
Federal holidays. The AD docket contains this AD, the mandatory 
continuing airworthiness information (MCAI), any comments received, and 
other information. The street address for Docket Operations is listed 
above.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
Large Aircraft Section, FAA, International Validation Branch, 2200 
South 216th St., Des Moines, WA 98198; telephone 206-231-3226; email 
[email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written data, views, or arguments 
about this final rule. Send your comments to an address listed under 
ADDRESSES. Include ``Docket No. FAA-2022-1067; Project Identifier MCAI-
2022-01042-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the final rule, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
this final rule because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
regulations.gov, including any personal information you provide. The 
agency will also post a report summarizing each substantive verbal 
contact received about this final rule.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this AD contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this AD, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this AD. Submissions containing CBI should be sent to Tom 
Rodriguez, Aerospace Engineer, Large Aircraft Section, FAA, 
International Validation Branch, 2200 South 216th St., Des Moines, WA 
98198; telephone 206-231-3226; email [email protected]. Any 
commentary that the FAA receives which is not specifically designated 
as CBI will be placed in the public docket for this rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA Emergency AD 2022-0161-E, dated August 
4, 2022 (EASA Emergency AD 2022-0161-E) (also referred to as the MCAI), 
to correct an unsafe condition for all Dassault Aviation Model FALCON 
7X airplanes.
    This AD was prompted by a report of a failed extension of inboard 
slats during the landing phase, which was not indicated to the 
flightcrew by the crew alerting system. The actual retracted inboard 
slats position, however, was correctly depicted by the flight control 
system synoptic. The FAA is issuing this AD to address failed extension 
of inboard slats without flightcrew indication, which could lead to 
reduced lift margin during approach and landing, and result in reduced 
control of the airplane. See the MCAI for additional background 
information.

Related Service Information Under 1 CFR Part 51

    EASA Emergency AD 2022-0161-E specifies revised procedures for the 
existing AFM for failed extension of inboard slats and flightcrew 
indication during landing. This material is reasonably available 
because the interested parties have access to it through their normal 
course of business or by the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI 
described above. The FAA is issuing this AD after determining that the 
unsafe condition described previously is likely to exist or develop on 
other products of the same type design.

Requirements of This AD

    This AD requires accomplishing the actions specified in EASA 
Emergency AD 2022-0161-E, described previously, as incorporated by 
reference, except for any differences identified as exceptions in the 
regulatory text of this AD.
    EASA Emergency AD 2022-0161-E requires operators to ``inform all 
flight crews'' of revisions to the AFM, and thereafter to ``operate the 
aeroplane accordingly.'' However, this AD does not specifically require 
those actions, as those actions are already required by FAA 
regulations. FAA regulations require operators furnish to pilots any 
changes to the AFM (for example, 14 CFR 121.137), and to ensure the 
pilots are familiar with the AFM (for example, 14 CFR 91.505). As with 
any other flightcrew training requirement, training on the updated AFM 
content is tracked by the operators and recorded in each pilot's 
training record, which is available for the FAA to review. FAA 
regulations also require pilots to follow the procedures in the 
existing AFM including all updates. 14 CFR 91.9 requires that any 
person operating a civil aircraft must comply with the operating 
limitations specified in the AFM. Therefore, including a requirement in 
this AD to operate the airplane according to the revised AFM would be 
redundant and unnecessary.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, 
EASA Emergency AD 2022-0161-E is incorporated by reference in this AD. 
This AD requires compliance with EASA Emergency AD 2022-0161-E in its 
entirety through that incorporation, except for any differences 
identified as exceptions in the regulatory text of this AD. Using 
common terms that are the same as the heading of a particular section 
in EASA Emergency AD 2022-0161-E does not mean that operators need 
comply only with that section. For example, where the AD requirement 
refers to ``all required actions and compliance times,'' compliance 
with this AD requirement is not limited to the section titled 
``Required Action(s) and Compliance Time(s)'' in EASA Emergency AD 
2022-0161-E. Service information required by EASA AD 2022-0161-E for 
compliance will be available at regulations.gov by searching for and 
locating Docket No. FAA-2022-1067 after this AD is published.

[[Page 54133]]

FAA's Justification and Determination of the Effective Date

    Section 553(b)(3)(B) of the Administrative Procedure Act (APA) (5 
U.S.C. 551 et seq.) authorizes agencies to dispense with notice and 
comment procedures for rules when the agency, for ``good cause,'' finds 
that those procedures are ``impracticable, unnecessary, or contrary to 
the public interest.'' Under this section, an agency, upon finding good 
cause, may issue a final rule without providing notice and seeking 
comment prior to issuance. Further, section 553(d) of the APA 
authorizes agencies to make rules effective in less than thirty days, 
upon a finding of good cause.
    An unsafe condition exists that requires the immediate adoption of 
this AD without providing an opportunity for public comments prior to 
adoption. The FAA has found that the risk to the flying public 
justifies forgoing notice and comment prior to adoption of this rule 
because of a report of a failed extension of inboard slats during the 
landing phase, which was not indicated to the flightcrew by the crew 
alerting system, and could lead to reduced lift margin during approach 
and landing, and possibly result in reduced control of the airplane. 
Additionally, this AD correlates with EASA Emergency AD 2022-0161-E, 
and addresses the unsafe condition by revising, within 10 flight cycles 
after the effective date of this AD, the procedures for failed 
extension of inboard slats and flightcrew indication during landing. 
Accordingly, notice and opportunity for prior public comment are 
impracticable and contrary to the public interest pursuant to 5 U.S.C. 
553(b)(3)(B).
    In addition, the FAA finds that good cause exists pursuant to 5 
U.S.C. 553(d) for making this amendment effective in less than 30 days, 
for the same reasons the FAA found good cause to forgo notice and 
comment.

Regulatory Flexibility Act (RFA)

    The requirements of the RFA do not apply when an agency finds good 
cause pursuant to 5 U.S.C. 553 to adopt a rule without prior notice and 
comment. Because the FAA has determined that it has good cause to adopt 
this rule without notice and comment, RFA analysis is not required.

Costs of Compliance

    The FAA estimates that this AD affects 142 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
1 work-hour x $85 per hour = $85.............................              $0              $85          $12,070
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866, and
    (2) Will not affect intrastate aviation in Alaska.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2022-18-18 Dassault Aviation: Amendment 39-22169; Docket No. FAA-
2022-1067; Project Identifier MCAI-2022-01042-T.

(a) Effective Date

    This airworthiness directive (AD) is effective September 19, 
2022.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all Dassault Aviation Model FALCON 7X 
airplanes, certificated in any category.
    Note 1 to paragraph (c): Model FALCON 7X airplanes with Dassault 
modification M1000 incorporated are commonly referred to as ``Model 
FALCON 8X'' as a marketing designation.

(d) Subject

    Air Transport Association (ATA) of America Code 27, Flight 
controls.

(e) Unsafe Condition

    This AD was prompted by a report of a failed extension of 
inboard slats during the landing phase, which was not indicated to 
the flightcrew by the crew alerting system. The FAA is issuing this 
AD to address failed extension of inboard slats without flightcrew 
indication, which could lead to reduced lift margin during approach 
and landing, and result in reduced control of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) 
Emergency AD 2022-0161-E, dated August 4, 2022 (EASA Emergency AD 
2022-0161-E).

[[Page 54134]]

(h) Exceptions to EASA Emergency AD 2022-0161-E

    (1) Where EASA Emergency AD 2022-0161-E refers to its effective 
date, this AD requires using the effective date of this AD.
    (2) Where EASA Emergency AD 2022-0161-E requires operators to 
``inform all flight crews, and, thereafter, operate the aeroplane 
accordingly,'' this AD does not require those actions.
    (3) The ``Remarks'' section of EASA Emergency AD 2022-0161-E 
does not apply to this AD.

(i) Additional AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch, send it 
to the attention of the person identified in paragraph (j) of this 
AD. Information may be emailed to: [email protected]. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Dassault 
Aviation's EASA Design Organization Approval (DOA). If approved by 
the DOA, the approval must include the DOA-authorized signature.

(j) Related Information

    For more information about this AD, contact Tom Rodriguez, 
Aerospace Engineer, Large Aircraft Section, FAA, International 
Validation Branch, 2200 South 216th St., Des Moines, WA 98198; 
telephone 206-231-3226; email [email protected].

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the service information listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) Emergency AD 
2022-0161-E, dated August 4, 2022.
    (ii) [Reserved]
    (3) For EASA Emergency AD 2022-0161-E, contact EASA, Konrad-
Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; 
email [email protected]; internet easa.europa.eu. You may find this 
EASA AD on the EASA website at ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on August 29, 2022.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft 
Certification Service.
[FR Doc. 2022-19116 Filed 8-31-22; 11:15 am]
BILLING CODE 4910-13-P