[Federal Register Volume 87, Number 28 (Thursday, February 10, 2022)]
[Rules and Regulations]
[Pages 7692-7695]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-02715]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0960; Project Identifier 2019-CE-021-AD; Amendment 
39-21921; AD 2022-03-04]
RIN 2120-AA64


Airworthiness Directives; Viking Air Limited (Type Certificate 
Previously Held by Bombardier, Inc. and de Havilland, Inc.) Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is superseding Airworthiness Directive (AD) 80-13-10, 
AD 80-13-12 R1, and AD 2008-03-01, which applied to certain de 
Havilland (type certificate now held by Viking Air Limited) Model DHC-
6-1, DHC-6-100, DHC-6-200, and DHC-6-300 airplanes. AD 80-13-10 
required repetitively inspecting the main landing gear (MLG) legs for 
cracks and corrosion. AD 80-13-12 R1 required repetitively inspecting 
each engine nacelle lower longeron for cracks and buckling. AD 2008-03-
01 required incorporating inspections, modifications, and life limits 
of certain structural components into the aircraft maintenance program. 
Since the FAA issued those ADs, new and more restrictive airworthiness 
limitations have been issued for certain structural components. This AD 
requires incorporating into maintenance records new or revised life 
limits, modification limits, and inspection or overhaul intervals. The 
FAA is issuing this AD to address the unsafe condition on these 
products.

DATES: This AD is effective March 17, 2022.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of March 17, 
2022.

ADDRESSES: For service information identified in this final rule, 
contact Viking Air Limited Technical Support, 1959 De Havilland Way, 
Sidney, British Columbia, Canada, V8L 5V5; phone: (North America) (800) 
663-8444; fax: (250) 656-0673; email: [email protected]; 
website: https://www.vikingair.com/support/service-bulletins. You may 
view this service information at the FAA, Airworthiness Products 
Section, Operational Safety Branch, 901 Locust, Kansas City, MO 64106. 
For information on the availability of this material at the FAA, call 
(817) 222-5110. It is also available at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-0960.

Examining the AD Docket

    You may examine the AD docket at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2021-0960; or in person at 
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, 
except Federal holidays. The AD docket contains this final rule, the 
mandatory continuing airworthiness information (MCAI), any comments 
received, and other information. The address for Docket Operations is 
U.S. Department of Transportation, Docket Operations, M-30, West 
Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, 
Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Aziz Ahmed, Aviation Safety Engineer, 
New York ACO Branch, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; phone: (516) 228-7329; fax: (516) 794-5531; email: 
[email protected].

SUPPLEMENTARY INFORMATION:

Background

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 to supersede AD 80-13-10, Amendment 39-3812 (45 FR 43155, 
June 26, 1980) (AD 80-13-10); AD 80-13-12 R1, Amendment 39-4135 (46 FR 
31251, June 15, 1981) (AD 80-13-12 R1); and AD 2008-03-01, Amendment 39 
15350 (73 FR 5729, January 31, 2008)

[[Page 7693]]

(AD 2008-03-01). AD 80-13-10 applied to de Havilland (type certificate 
now held by Viking Air Limited) Model ``DHC-6 type'' airplanes with 
certain MLG legs and required repetitively inspecting the weld juncture 
at the Y-joint of the MLG legs for cracks and corrosion. AD 80-13-12 R1 
applied to certain serial-numbered de Havilland (now Viking Air 
Limited) Model ``DHC-6 type'' airplanes with intermediate or high 
floatation tires, skis, or floats and required repetitively inspecting 
each engine nacelle lower longeron for cracks and buckling. AD 2008-03-
01 applied to all Viking Air Limited Model DHC-6-1, DHC-6-100, DHC-6-
200, and DHC-6-300 airplanes and required incorporating the 
inspections, modifications, and life limits (retirement) of certain 
structural components, as contained in Revision 5 of the DHC-6 Product 
Support Manual (PSM) 1-6-11, into the aircraft maintenance program. The 
NPRM published in the Federal Register on November 8, 2021 (86 FR 
61719).
    The NPRM was prompted by Canadian AD CF-2019-02, dated January 9, 
2019 (referred to after this as ``the MCAI''), issued by Transport 
Canada, which is the aviation authority for Canada. The MCAI applies to 
all Viking Air Limited (formerly de Havilland) Model DHC-6 series 1, 
DHC-6 series 100, DHC-6 series 110, DHC-6 series 200, DHC-6 series 210, 
DHC-6 series 300, DHC-6 series 310, DHC-6 series 320, and DHC-6 series 
400 airplanes. The MCAI states:

    The airworthiness limitations for DHC-6 aeroplanes are defined 
and published in the Viking Air Ltd. (Viking) Airframe Airworthiness 
Limitations Manual, Product Support Manual (PSM) 1-6-11, approved by 
Transport Canada. The instructions contained in PSM 1-6-11 have been 
identified as mandatory actions for continued airworthiness. Failure 
to comply with those instructions could result in an unsafe 
condition.
    Viking Air Ltd. published Revision 9 of PSM 1-6-11 earlier in 
2018. Revision 9 of PSM 1-6-11, dated 30 April 2018, includes some 
new and/or more restrictive limitations than those contained in 
Revision 5. For the reason described above, this [Transport Canada] 
AD requires implementation of the actions specified in PSM 1-6-11 
Revision 9.
    The compliance requirements for several of the tasks in PSM 1-6-
11 were previously a range of flight hours and flight cycles. With 
Revision 9 of PSM 1-6-11, the range-based requirements have been 
changed to specific flight hours and flight cycle limits. This 
[Transport Canada] AD provides a phase-in allowance for those 
limitations so that operators will have the opportunity to schedule 
the modifications and inspections required by the limitations. The 
phase-in allowances are intended to mitigate the impact of changing 
from compliance ranges to compliance limits for aeroplanes that are 
approaching or have exceeded the limits on the effective date of the 
[Transport Canada] AD.
    Revision 9 of PSM 1-6-11 also includes some airworthiness 
limitations that were previously contained in service bulletins (SB) 
or other PSMs. Some of those limitations were mandated by [Transport 
Canada] ADs, specifically AD CF-80-06, CF-81-07R4 and CF-95-12. 
Because the affected limitations will now be controlled in PSM 1-6-
11, the above mentioned [Transport Canada] ADs are superseded by 
this [Transport Canada] AD.
    The following are new tasks in PSM 1-6-11 Revision 9:
    1. Task 27-007 Replacement of flight control pulleys at Fuselage 
Station (FS) 270.
    2. Tasks 32-001 and 32-002 Overhaul of main landing gear leg. 
There is an associated requirement to ensure that each affected part 
has been assigned a unique serial number.
    3. Task 53-006 Inspection of the skin flange of machined frame 
at FS 239.
    4. Tasks 54-003 to 54-010 Inspection of nacelle longerons.
    5. Tasks 57-039 to 57-041 Inspection for wing upper skin 
disbond.
    Task 27-004 Replacement of flight control cables after spillage 
of corrosive materials in PSM 1-6-11 was limited to landplane 
configurations in previous revisions of PSM 1-6-11 but is now 
applicable to all configurations.
    The intent of the word ``airframe'' in PSM 1-6-11 Revision 9 is 
to include fuselage, nacelles, struts, interiors, cowlings, 
fairings, airfoils, landing gear and their controls. The airframe 
life limitation in PSM 1-6-11 Revision 9 is not intended to apply to 
components such as those in the fuel, electrical and hydraulic 
systems that are occasionally transferred from one aeroplane to 
another and may be salvaged from an aeroplane that is retired from 
service for use on an in-service aeroplane. PSM 1-6-13 defines 
current airworthiness limitations for DHC-6 avionics that are not 
addressed in this [Transport Canada] AD.

    Model DHC-6-400 airplanes were type certificated after Transport 
Canada AD CF-2000-14 was issued and are subject to the same unsafe 
condition. You may examine the MCAI in the AD docket at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
0960.

Discussion of Final Airworthiness Directive

Comments

    The FAA received no comments on the NPRM or on the determination of 
the costs.

Conclusion

    This product has been approved by the aviation authority of another 
country and is approved for operation in the United States. Pursuant to 
the FAA's bilateral agreement with this State of Design Authority, it 
has notified the FAA of the unsafe condition described in the MCAI and 
service information referenced above. The FAA determined that air 
safety requires adopting this AD as proposed. Accordingly, the FAA is 
issuing this AD to address the unsafe condition on these products. This 
AD is adopted as proposed in the NPRM.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Viking Air Limited DHC-6 Twin Otter PSM 1-6-11, 
Airframe Airworthiness Limitations Manual, Revision 9, dated April 30, 
2018. The service information contains airworthiness limitations for 
certain structural components. This service information is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in 
ADDRESSES.

ADs Mandating Airworthiness Limitations

    The FAA has previously mandated airworthiness limitations by 
issuing ADs that require revising the airworthiness limitation section 
(ALS) of the existing maintenance manual or instructions for continued 
airworthiness to incorporate new or revised inspections and life 
limits. This AD, however, requires incorporating new or revised 
inspections and life limits into the maintenance records required by 14 
CFR 91.417(a)(2) or 135.439(a)(2) for your airplane. The FAA does not 
intend this as a substantive change. Requiring incorporation of the new 
ALS requirements into the maintenance records, rather than requiring 
individual repetitive inspections and replacements, allows operators to 
record AD compliance once after updating the maintenance records, 
rather than recording compliance after every inspection and part 
replacement.

Differences Between This AD and the MCAI

    The MCAI applies to Viking Air Limited Model DHC-6 series 110, DHC-
6 series 210, DHC-6 series 310, and DHC-6 series 320, and this AD does 
not because these models do not have an FAA type certificate. Transport 
Canada Models DHC-6 series 1, DHC-6 series 100, DHC-6 series 200, DHC-6 
series 300, and DHC-6 series 400 airplanes correspond to FAA Model DHC-
6-1, DHC-6-100, DHC-6-200, DHC-6-300, and DHC-6-400 airplanes, 
respectively.

Costs of Compliance

    The FAA estimates that this AD affects 33 airplanes of U.S. 
registry.

[[Page 7694]]

    The FAA also estimates that it would take about 1 work-hour per 
airplane to incorporate life limits, modification limits, and 
inspection or overhaul intervals into maintenance records. The average 
labor rate is $85 per work-hour.
    Based on these figures, the FAA estimates the cost of this AD on 
U.S. operators to be $2,805 or $85 per airplane.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government. For the reasons discussed above, I certify that 
this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by
0
a. Removing Airworthiness Directive 80-13-10, Amendment 39-3812 (45 FR 
43155, June 26, 1980); Airworthiness Directive 80-13-12 R1, Amendment 
39-4135 (46 FR 31251, June 15, 1981); and Airworthiness Directive 2008-
03-01, Amendment 39-15350 (73 FR 5729, January 31, 2008); and
0
b. Adding the following new airworthiness directive:

2022-03-04 Viking Air Limited (Type Certificate Previously Held by 
Bombardier, Inc. and de Havilland, Inc.): Amendment 39-21921; Docket 
No. FAA-2021-0960; Project Identifier 2019-CE-021-AD.

(a) Effective Date

    This airworthiness directive (AD) is effective March 17, 2022.

(b) Affected ADs

    This AD replaces the ADs specified in paragraphs (b)(1) through 
(3) of this AD.
    (1) AD 80-13-10, Amendment 39-3812 (45 FR 43155, June 26, 1980).
    (2) AD 80-13-12 R1, Amendment 39-4135 (46 FR 31251, June 15, 
1981).
    (3) AD 2008-03-01 Amendment 39-15350 (73 FR 5729, January 31, 
2008).

(c) Applicability

    This AD applies to Viking Air Limited (type certificate 
previously held by Bombardier, Inc. and de Havilland, Inc.) Model 
DHC-6-1, DHC-6-100, DHC-6-200, DHC-6-300, and DHC-6-400 airplanes, 
all serial numbers, certificated in any category.

(d) Subject

    Joint Aircraft System Component (JASC) Code 0500, Time Limits.

(e) Unsafe Condition

    This AD was prompted by mandatory continuing airworthiness 
information (MCAI) originated by an aviation authority of another 
country to identify and correct an unsafe condition on an aviation 
product. The MCAI identifies the unsafe condition as failure to 
comply with new and more restrictive airworthiness limitations, 
including tasks where range-based requirements have been changed to 
specific hours time-in-service (TIS) and flight cycle limits. The 
FAA is issuing this AD to prevent loss of structural integrity of 
certain parts. The unsafe condition, if not addressed, could result 
in loss of control of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Maintenance and Life Limits

    (1) Within 30 days after the effective date of this AD, 
incorporate into the maintenance records required by 14 CFR 
91.417(a)(2) or 135.439(a)(2) for your airplane the life limits, 
modification limits, and inspection or overhaul intervals in Viking 
Air Limited DHC-6 Twin Otter PSM 1-6-11, Airframe Airworthiness 
Limitations Manual, Revision 9, dated April 30, 2018 (Viking Air 
Limited PSM 1-6-11, Revision 9).
    (2) Before further flight after revising the maintenance records 
as required by paragraph (g)(1) of this AD, except as allowed under 
paragraph (h) of this AD, remove from service each part that has 
reached or exceeded its life limit and modify each part that has 
reached or exceeded its modification limit.
    (3) Before further flight after revising the maintenance records 
as required by paragraph (g)(1) of this AD, except as allowed under 
paragraph (h) of this AD, inspect or overhaul each part that has 
reached or exceeded its inspection or overhaul interval.

(h) Phase-in Period

    The following phase-in periods are allowed to comply with the 
initial tasks in Viking Air Limited PSM 1-6-11, Revision 9.
    (1) Task 27-007: For any pulley that has been in service for 48 
or more months on the effective date of this AD, replace the pulley 
within 12 months after the effective date of this AD.
    (2) Tasks 32-001 and 32-002:
    (i) For any main landing gear (MLG) leg that, on the effective 
date of this AD, has not been marked with a new serial number as 
specified in Viking DHC-6 Twin Otter Technical Bulletin V6/00063: 
Within 6 months after the effective date of this AD, inspect and 
serialize the MLG leg. The absence of a serial number indicates that 
the initial inspection of the landing gear leg has not previously 
been accomplished.
    (ii) For all other MLG legs, overhaul the MLG leg within 60 
months after the last overhaul.
    (3) Tasks 57-006, 57-007, 57-010, 57-011, 57-013, and 57-014:
    (i) For any wing that on the effective date of this AD has 
accumulated more than 16,000 hours total TIS or 32,000 total flight 
cycles but less than 17,000 hours total TIS or less than 34,000 
total flight cycles, accomplish the task within 1,000 hours TIS or 
2,000 flight cycles, whichever occurs first after the effective date 
of this AD.
    (ii) For any wing that on the effective date of this AD has 
accumulated 17,000 or more hours total TIS or 34,000 or more total 
flight cycles, accomplish the task before accumulating 18,000 hours 
total TIS or 36,000 total flight cycles, or within 60 months after 
the effective date of this AD, whichever occurs first.
    (4) Tasks 57-018, 57-019, 57-022, 57-023, 57-026, 57-027, 57-
030, and 57-031:
    (i) For any wing that on the effective date of this AD has 
accumulated more than 11,000 hours total TIS or 22,000 total flight 
cycles but less than 12,000 hours total TIS or less than 24,000 
total flight cycles, accomplish the task within 1,000 hours TIS or 
2,000 flight cycles, whichever occurs first after the effective date 
of this AD.

[[Page 7695]]

    (ii) For any wing that on the effective date of this AD has 
accumulated 12,000 or more hours total TIS or 24,000 or more total 
flight cycles, accomplish the task before accumulating 13,000 hours 
total TIS or 26,000 total flight cycles or within 60 months after 
the effective date of this AD, whichever occurs first.
    (5) Tasks 57-039 to 57-041 inclusive: For any wing that on the 
effective date of this AD has more than 20 years since the date of 
manufacture and has not previously been inspected in accordance with 
Viking Service Bulletin V6/0018, inspect the wing upper surface 
within 120 days after the effective date of this AD.

(i) No Alternative Actions or Intervals

    After the maintenance records have been revised as required by 
paragraph (g) of this AD, no alternative actions (e.g., inspections) 
or intervals may be used unless the actions or intervals are 
approved as an alternative method of compliance (AMOC) in accordance 
with the procedures specified in paragraph (j)(1) of this AD.

(j) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, New York ACO Branch, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request 
to your principal inspector or local Flight Standards District 
Office, as appropriate. If sending information directly to the 
manager of the certification office, send it to the attention of the 
person identified in paragraph (k)(1) of this AD.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.

(k) Related Information

    (1) For more information about this AD, contact Aziz Ahmed, 
Aviation Safety Engineer, New York ACO Branch, FAA,1600 Stewart 
Avenue, Suite 410, Westbury, NY 11590; phone: (516) 228-7329; fax: 
(516) 794-5531; email: [email protected].
    (2) Refer to Transport Canada AD CF-2019-02, dated January 9, 
2019, for more information. You may examine the Transport Canada AD 
in the AD docket at https://www.regulations.gov by searching for and 
locating Docket No. FAA-2021-0960.

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the service information listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Viking Air Limited DHC-6 Twin Otter PSM 1-6-11, Airframe 
Airworthiness Limitations Manual, Revision 9, dated April 30, 2018.
    (ii) [Reserved]
    (3) For service information identified in this AD, contact 
Viking Air Limited Technical Support, 1959 De Havilland Way, Sidney, 
British Columbia, Canada, V8L 5V5; phone: (North America) (800) 663-
8444; fax: (250) 656-0673; email: [email protected]; 
website: https://www.vikingair.com/support/service-bulletins.
    (4) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 901 
Locust, Kansas City, MO 64106. For information on the availability 
of this material at the FAA, call (817) 222-5110.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, email: [email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on January 20, 2022.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2022-02715 Filed 2-9-22; 8:45 am]
BILLING CODE 4910-13-P