[Federal Register Volume 87, Number 13 (Thursday, January 20, 2022)]
[Proposed Rules]
[Pages 3050-3052]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-00884]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2022-0005; Project Identifier MCAI-2021-01062-R]
RIN 2120-AA64
Airworthiness Directives; Airbus Helicopters
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for all Airbus Helicopters Model EC130T2 helicopters. This proposed AD
was prompted by the determination of a certain part needing a life
limit and re-identification. This proposed AD would require re-
identifying a certain part-numbered engine-to-main gearbox (engine-MGB)
coupling shaft, and creating a log card or equivalent record, as
specified in a European Union Aviation Safety Agency (EASA) AD, which
is proposed for incorporation by reference (IBR). The FAA is proposing
this AD to address the unsafe condition on these products.
DATES: The FAA must receive comments on this proposed AD by March 7,
2022.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
Fax: (202) 493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building, Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
Hand Delivery: Deliver to mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For EASA material that is proposed for IBR in this AD, contact the
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; phone: +49 221
8999 000; email: [email protected]; internet: www.easa.europa.eu. You
may find the EASA material on the EASA website at https://ad.easa.europa.eu. You may view this material at the FAA, Office of the
Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 6N-321,
Fort Worth, TX 76177. For information on the availability of this
material at the FAA, call (817) 222-5110. This material is also
available at https://www.regulations.gov by searching for and locating
Docket No. FAA-2022-0005.
Examining the AD Docket
You may examine the AD docket at https://www.regulations.gov by
searching for and locating Docket No. FAA-2022-0005; or in person at
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The AD docket contains this NPRM, the EASA AD,
any comments received, and other information. The street address for
Docket Operations is listed above.
FOR FURTHER INFORMATION CONTACT: Andrea Jimenez, Aerospace Engineer,
COS Program Management Section, Operational Safety Branch, Compliance &
Airworthiness Division, FAA, 1600 Stewart Ave., Suite 410, Westbury, NY
11590; telephone (516) 228-7330; email [email protected].
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under ADDRESSES. Include ``Docket No. FAA-2022-0005; Project Identifier
MCAI-2021-01062-R'' at the beginning of your comments. The most helpful
comments reference a specific portion of the proposal, explain the
reason for any recommended change, and include supporting data. The FAA
will consider all comments received by the closing
[[Page 3051]]
date and may amend this proposal because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
https://www.regulations.gov, including any personal information you
provide. The agency will also post a report summarizing each
substantive verbal contact received about this NPRM.
Confidential Business Information
CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this NPRM contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this NPRM, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this NPRM. Submissions containing CBI should be sent to
Andrea Jimenez, Aerospace Engineer, COS Program Management Section,
Operational Safety Branch, Compliance & Airworthiness Division, FAA,
1600 Stewart Ave., Suite 410, Westbury, NY 11590; telephone (516) 228-
7330; email [email protected]. Any commentary that the FAA
receives that is not specifically designated as CBI will be placed in
the public docket for this rulemaking.
Background
EASA, which is the Technical Agent for the Member States of the
European Union, has issued EASA AD 2021-0216, dated September 23, 2021
(EASA AD 2021-0216), to correct an unsafe condition for Airbus
Helicopters (AH), formerly Eurocopter, Model EC 130 T2 helicopters, all
serial numbers.
This proposed AD was prompted by the determination from recent
analysis related to service life, for the need to introduce a service
life limit (life limit) in torque cycles for engine-MGB coupling shaft
part number (P/N) 350A35-1100-21. The FAA is proposing this AD to
address the unsafe condition, which if not corrected could lead to
fatigue failure of the affected part, and loss of control of the
helicopter. See EASA AD 2021-0216 for additional background
information.
Related Service Information Under 1 CFR Part 51
EASA AD 2021-0216 requires re-identifying each affected engine-MGB
coupling shaft, by crossing out the old P/N and marking the new P/N and
serial number (S/N), and creating a log card indicating the new P/N, S/
N, and the initial value of accumulated torque cycles. EASA AD 2021-
0216 also prohibits installing an affected engine-MGB coupling shaft on
any helicopter.
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in the ADDRESSES section.
Other Related Service Information
The FAA reviewed Airbus Helicopters Alert Service Bulletin No.
EC130-04A010, dated July 15, 2021 (ASB EC130-04A010). This service
information specifies procedures for re-identifying the engine-MGB
coupling shaft by crossing out the old P/N and marking the new P/N and
a new S/N using a vibration scriber. ASB EC130-04A010 also specifies
instructions for creating a log card for the engine-MGB coupling shaft
indicating the new P/N, the new S/N, and the number of torque cycles.
Finally, ASB EC130-04A010 specifies instructions for calculating the
number of torque cycles that are required to be indicated on the log
card.
FAA's Determination
These helicopters have been approved by EASA and are approved for
operation in the United States. Pursuant to the FAA's bilateral
agreement with the European Union, EASA has notified the FAA about the
unsafe condition described in its AD. The FAA is proposing this AD
after evaluating all known relevant information and determining that
the unsafe condition described previously is likely to exist or develop
on other helicopters of the same type design.
Proposed AD Requirements in This NPRM
This proposed AD would require accomplishing the actions specified
in EASA AD 2021-0216, described previously, as incorporated by
reference, except for any differences identified as exceptions in the
regulatory text of this proposed AD and except as discussed under
``Differences Between this Proposed AD and EASA AD 2021-0216.''
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA developed a process to use some civil aviation
authority (CAA) ADs as the primary source of information for compliance
with requirements for corresponding FAA ADs. The FAA has been
coordinating this process with manufacturers and CAAs. As a result, the
FAA proposes to incorporate EASA AD 2021-0216 by reference in the FAA
final rule. This proposed AD would, therefore, require compliance with
EASA AD 2021-0216 in its entirety through that incorporation, except
for any differences identified as exceptions in the regulatory text of
this proposed AD. Using common terms that are the same as the heading
of a particular section in EASA AD 2021-0216 does not mean that
operators need comply only with that section. For example, where the AD
requirement refers to ``all required actions and compliance times,''
compliance with this AD requirement is not limited to the section
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2021-
0216. Service information referenced in EASA AD 2021-0216 for
compliance will be available at https://www.regulations.gov by
searching for and locating Docket No. FAA-2022-0005 after the FAA final
rule is published.
Differences Between This Proposed AD and EASA AD 2021-0216
Service information referenced in EASA AD 2021-0216 specifies
sending certain information to the manufacturer; this proposed AD would
not. Paragraph (1) of EASA AD 2021-0216 specifies a compliance time of
before exceeding 660 flight hours or 24 months after the effective date
of this AD, whichever occurs first. However, this proposed AD would
require compliance before exceeding 660 hours time-in-service or 24
months after the effective date of this proposed AD, whichever occurs
first.
Costs of Compliance
The FAA estimates that this AD, if adopted as proposed, would
affect 264 helicopters of U.S. Registry. Labor rates are estimated at
$85 per work-hour. Based on these numbers, the FAA estimates the
following costs to comply with this proposed AD.
Re-identifying the engine-MGB coupling shaft would take about 4
work-hours for an estimated cost of $340 per helicopter and up to
$89,760 for the U.S. fleet.
Creating a log card or equivalent record would take about 1 work-
hour for
[[Page 3052]]
an estimated cost of $85 per log card and up to $22,440 for the U.S.
fleet.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Would not affect intrastate aviation in Alaska, and
(3) Would not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
Airbus Helicopters: Docket No. FAA-2022-0005; Project Identifier
MCAI-2021-01062-R.
(a) Comments Due Date
The FAA must receive comments on this airworthiness directive
(AD) by March 7, 2022.
(b) Affected ADs
None.
(c) Applicability
This AD applies to all Airbus Helicopters Model EC130T2
helicopters, certificated in any category.
(d) Subject
Joint Aircraft Service Component (JASC) Code: 6300, Main Rotor
Drive System.
(e) Unsafe Condition
This AD was prompted by the determination of a certain part
needing a life limit and re-identification. The FAA is issuing this
AD to prevent fatigue failure of the engine-to-main gearbox (engine-
MGB) coupling shaft, which if not corrected, could result in loss of
control of the helicopter.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
Except as specified in paragraph (h) of this AD: Comply with all
required actions and compliance times specified in, and in
accordance with, European Union Aviation Safety Agency (EASA) AD
2021-0216, dated September 23, 2021 (EASA AD 2021-0216).
(h) Exceptions to EASA AD 2021-0216
(1) Where EASA AD 2021-0216 requires compliance in terms of
flight hours, this AD requires using hours time-in-service.
(2) Where EASA AD 2021-0216 refers to its effective date, this
AD requires using the effective date of this AD.
(3) Where paragraph (1) of EASA AD 2021-0216 specifies ``in
accordance with the instructions of section 3.B of the ASB,'' for
this AD replace ``in accordance with the instructions of section 3.B
of the ASB'' with ``in accordance with the Accomplishment
Instructions, paragraphs 3.B.2. through 3.B.2.b. of the of the
ASB.''
(4) Where Note 1 of the service information referenced in EASA
AD 2021-0216 specifies to contact Airbus Helicopters if you have
more than one non-installed engine-MGB coupling shaft, this AD does
not require contacting Airbus Helicopters.
(5) Where the service information referenced in EASA AD 2021-
0216 specifies to use a vibration scriber to re-identify the engine-
MGB coupling shaft, this AD allows the use of equivalent tooling.
(6) Where the service information referenced in EASA AD 2021-
0216 specifies creating a log card for the engine-MGB coupling
shaft, this AD requires creating a log card or equivalent record.
(7) This AD does not mandate compliance with the ``Remarks''
section of EASA AD 2021-0216.
(i) No Reporting Requirement
Although the service information referenced in EASA AD 2021-0216
specifies to submit certain information to the manufacturer, this AD
does not include that requirement.
(j) Special Flight Permit
Special flight permits may be issued in accordance with 14 CFR
21.197 and 21.199, provided no passengers are onboard.
(k) Alternative Methods of Compliance (AMOCs)
(1) The Manager, International Validation Branch, FAA, has the
authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the manager of the International Validation Branch, send
it to the attention of the person identified in paragraph (l)(2) of
this AD. Information may be emailed to: [email protected].
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
(l) Related Information
(1) For EASA AD 2021-0216, contact EASA, Konrad-Adenauer-Ufer 3,
50668 Cologne, Germany; telephone +49 221 8999 000; email
[email protected]; internet www.easa.europa.eu. You may view this
material at the FAA, Office of the Regional Counsel, Southwest
Region, 10101 Hillwood Pkwy., Room 6N-321, Fort Worth, TX 76177. For
information on the availability of this material at the FAA, call
(817) 222-5110. This material may be found in the AD docket at
https://www.regulations.gov by searching for and locating Docket No.
FAA-2022-0005.
(2) For more information about this AD, contact Andrea Jimenez,
Aerospace Engineer, COS Program Management Section, Operational
Safety Branch, Compliance & Airworthiness Division, FAA, 1600
Stewart Ave., Suite 410, Westbury, NY 11590; telephone (516) 228-
7330; email [email protected].
Issued on January 10, 2022.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification
Service.
[FR Doc. 2022-00884 Filed 1-19-22; 8:45 am]
BILLING CODE 4910-13-P