[Federal Register Volume 87, Number 12 (Wednesday, January 19, 2022)]
[Rules and Regulations]
[Pages 2699-2702]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2022-00891]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2021-0793; Project Identifier MCAI-2021-00372-E;
Amendment 39-21885; AD 2021-26-26]
RIN 2120-AA64
Airworthiness Directives; Safran Helicopter Engines, S.A. (Type
Certificate Previously Held by Turbomeca S.A.) Turboshaft Engines
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is superseding Airworthiness Directive (AD) 2005-12-08
for certain Safran Helicopter Engines, S.A. (Safran Helicopter Engines)
Arrius 2B1, 2B1A, 2B1A-1, and 2B2 model turboshaft engines. AD 2005-12-
08 required replacing the software in the engine electronic control
unit (EECU). This AD was prompted by a report of simultaneous loss of
automatic control on both engines installed on an Airbus Helicopters
Deutschland (formerly Eurocopter Deutschland) EC135 helicopter during
flight. This AD requires replacement of the EECU or upgrade of the EECU
software for engines with a certain EECU part number (P/N) installed.
This AD also prohibits installation of an affected EECU onto any
engine. The FAA is issuing this AD to address the unsafe condition on
these products.
DATES: This AD is effective February 23, 2022.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in this AD as of February 23,
2022.
The Director of the Federal Register approved the incorporation by
reference of certain other publications listed in this AD as of June
29, 2005 (70 FR 34334, June 14, 2005).
ADDRESSES: For service information identified in this final rule,
contact Safran Helicopter Engines, S.A., Avenue du 1er Mai, 40220
Tarnos, France; phone: +33 (0) 5 59 74 45 00. You may view this service
information at the Airworthiness Products Section,
[[Page 2700]]
Operational Safety Branch, FAA, 1200 District Avenue, Burlington, MA
01803. For information on the availability of this material at the FAA,
call (817) 222-5110. It is also available at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
0793.
Examining the AD Docket
You may examine the AD docket at https://www.regulations.gov by
searching for and locating Docket No. FAA-2021-0793; or in person at
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The AD docket contains this final rule, the
mandatory continuing airworthiness information (MCAI), any comments
received, and other information. The address for Docket Operations is
Document Operations, U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Wego Wang, Aviation Safety Engineer,
ECO Branch, FAA, 1200 District Avenue, Burlington, MA 01803; phone:
(781) 238-7134; fax: (781) 238-7199; email: [email protected].
SUPPLEMENTARY INFORMATION:
Background
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 to supersede AD 2005-12-08, Amendment 39-14124 (70 FR
34334, June 14, 2005), (AD 2005-12-08). AD 2005-12-08 applied to all
Safran Helicopter Engines (Type Certificate previously held by
Turbomeca S.A.) Arrius 2 B1, 2 B1A, 2 B1A-1, and 2 B2 model turboshaft
engines. These engines are installed on, but not limited to, Eurocopter
Deutschland GmbH EC 135T1 and EC 135 T2 helicopters. The NPRM published
in the Federal Register on September 20, 2021 (86 FR 52106). The NPRM
was prompted by a report of simultaneous loss of automatic control on
both engines installed on an Airbus Helicopters Deutschland (formerly
Eurocopter Deutschland) EC135 helicopter during flight. In addition,
the manufacturer more recently determined that certain EECUs identified
in AD 2005-12-08 are not subject to the unsafe condition. In the NPRM,
the FAA proposed to require replacement of the EECU or upgrade of the
EECU software for engines with a certain EECU P/N installed. In the
NPRM, the FAA also proposed to prohibit installation of an affected
EECU onto any engine. The FAA is issuing this AD to address the unsafe
condition on these products.
The European Union Aviation Safety Agency (EASA), which is the
Technical Agent for the Member States of the European Community, has
issued EASA AD 2021-0088, dated March 24, 2021. EASA AD 2021-0088 was
revised by EASA AD 2021-0088R1, dated July 26, 2021 (referred to after
this as ``the MCAI''), to address the unsafe condition on these
products. The MCAI states:
An occurrence was reported of simultaneous loss of automatic
control in flight of both ARRIUS 2B1 engines on an EC135 T1
helicopter. Loss of automatic control would result, for each engine,
from a difference between the position datum of the fuel metering
valve and its measured position.
This condition, if not corrected, could lead to increased work
for flight crew during certain flight phases, possibly resulting in
reduced control of the helicopter.
To address this potential unsafe condition, Turbomeca developed
mod TU80C, TU81C, TU82C and TU90C to improve the DECU software for
ARRIUS 2B1 engines without overspeed option, ARRIUS 2B1 engines with
overspeed option, ARRIUS 2B1A and ARRIUS 2B2 engines, and DGAC
France issued AD F-2004-017 (later revised) to require engine
modification.
Since that [DGAC France] AD was issued, it was determined that a
DECU having a P/N which corresponds to Turbomeca mod TU80C, TU81C,
TU82C, TU90C or later software is not affected by the software
modification requirement. DGAC France AD F-2004-017R1 did not
specifically identify any affected DECU P/N(s).
For the reason described above, this [EASA] AD retains the
requirements of DGAC France AD F-2004-017R1 (EASA approval 2004-
1618), which is superseded, and limits the required actions to
engines with an affected DECU P/N installed. This [EASA] AD also
prohibits (re)installation of affected DECU on any engine.
This [EASA] AD is revised to provide clarification on affected
and serviceable DECU.
You may obtain further information by examining the MCAI in the AD
docket at https://www.regulations.gov by searching for and locating
Docket No. FAA-2021-0793.
Discussion of Final Airworthiness Directive
Comments
The FAA received a comment from one individual commenter. The
commenter supported the NPRM without change.
Conclusion
The FAA reviewed the relevant data, considered the comment
received, and determined that air safety and the public interest
require adopting this AD as proposed. Accordingly, the FAA is issuing
this AD to address the unsafe condition on these products. This AD is
adopted as proposed in the NPRM.
Related Service Information Under 1 CFR Part 51
The FAA reviewed Turbomeca Mandatory Service Bulletin (MSB) No. 319
73 2080, Revision 1, dated February 13, 2004; Turbomeca MSB No. 319 73
2081, Revision 1, dated February 13, 2004; Turbomeca MSB No. 319 73
2082, Revision 1, dated February 13, 2004, Version C, dated July 31,
2008, and Version D, dated June 6, 2011; and Turbomeca MSB No. 319 73
2090, Original Issue, dated February 13, 2004. This service information
specifies procedures for upgrading the EECU by either replacing the
EECU or by uploading the software to the EECU. These documents are
distinct since they apply to different engine models in different
configurations. The Director of the Federal Register previously
approved Turbomeca MSB No. 319 73 2080, Revision 1, dated February 13,
2004; Turbomeca MSB No. 319 73 2081, Revision 1, dated February 13,
2004; Turbomeca MSB No. 319 73 2082, Revision 1, dated February 13,
2004; and Turbomeca MSB No. 319 73 2090, Original Issue, dated February
13, 2004 for incorporation by reference on June 29, 2005 (70 FR 34334,
June 14, 2005). This service information is reasonably available
because the interested parties have access to it through their normal
course of business or by the means identified in ADDRESSES.
Costs of Compliance
The FAA estimates that this AD affects 221 engines installed on
helicopters of U.S. registry.
The FAA estimates the following costs to comply with this AD:
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost per Cost on U.S.
Action Labor cost Parts cost product operators
----------------------------------------------------------------------------------------------------------------
Replace the EECU...................... 1 work-hour x $85 per $35,000 $35,085 $7,753,785
hour = $85.
[[Page 2701]]
Upgrade the EECU software............. 2 work-hours x $85 per 0 170 37,570
hour = $170.
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA has determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends part 39 of the Federal Aviation
Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by:
0
a. Removing Airworthiness Directive 2005-12-08, Amendment 39-14124 (70
FR 34334, June 14, 2005); and
0
b. Adding the following new airworthiness directive:
2021-26-26 Safran Helicopter Engines, S.A. (Type Certificate
previously held by Turbomeca S.A.): Amendment 39-21885; Docket No.
FAA-2021-0793; Project Identifier MCAI-2021-00372-E.
(a) Effective Date
This airworthiness directive (AD) is effective February 23,
2022.
(b) Affected ADs
This AD replaces AD 2005-12-08, Amendment 39-14124 (70 FR 34334,
June 14, 2005).
(c) Applicability
This AD applies to Safran Helicopter Engines, S.A. (Type
Certificate previously held by Turbomeca S.A.) Arrius 2B1, Arrius
2B1A, (including those that embody modification (mod) TU45C,
identified as Arrius 2B1A_1) and Arrius 2B2 model turboshaft engines
with an installed engine electronic control unit (EECU) having part
number (P/N) 70EMF01080 or 70EMF01090--for Arrius 2B1 model
turboshaft engines without overspeed protection option (TU 19C); P/N
70EMF01100 or P/N 70EMF01120--for Arrius 2B1 model turboshaft
engines with overspeed protection option (TU 67C or TU 23C); P/N
70EMH01000 or 70EMH01010--for Arrius 2B1A model turboshaft engines;
or P/N 70EMM01000--for Arrius 2B2 model turboshaft engines.
Note 1 to paragraph (c): Turbomeca Mandatory Service Bulletin
(MSB) No. 319 73 2082, Version D, dated June 6, 2011, references
Arrius 2B1A_1 model turboshaft engines. Arrius 2B1A model turboshaft
engines with mod TU 45C applied are identified as Arrius 2B1A_1 on
the engine identification plate.
(d) Subject
Joint Aircraft System Component (JASC) Code 7600, Engine
Controls.
(e) Unsafe Condition
This AD was prompted by a report of simultaneous loss of
automatic control on both engines installed on an Airbus Helicopters
Deutschland (formerly Eurocopter Deutschland) EC135 helicopter
during flight. The FAA is issuing this AD to prevent simultaneous
loss of automatic control of both engines. The unsafe condition, if
not addressed, could result in failure of the engines and loss of
control of the helicopter.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Required Actions
(1) For engines with an EECU having P/N 70EMF01090, 70EMF01100,
70EMF01120, 70EMH01010, or 70EMM01000, within 90 days after June 29,
2005 (the effective date of AD 2005-12-08), or before further
flight, whichever occurs later, upload the EECU software on both
engines of the helicopter simultaneously using paragraph 2,
Instructions to be incorporated, of the applicable Turbomeca MSB
listed in Table 1 to paragraph (g) of this AD, or replace the
affected EECU with a part eligible for installation.
(2) For engines with an EECU having P/N 70EMF01080 or
70EMH01000, within 90 days after June 29, 2005 (the effective date
of AD 2005-12-08), or before further flight, whichever occurs later,
replace the affected EECU with a part eligible for installation.
BILLING CODE 4910-13-P
[[Page 2702]]
[GRAPHIC] [TIFF OMITTED] TR19JA22.076
BILLING CODE 4910-13-C
(h) Installation Prohibition
After the effective date of this AD, do not install onto any
engine any EECU having a P/N identified in paragraph (c) of this AD.
(i) Definition
For the purpose of this AD, a ``part eligible for installation''
is an EECU having a P/N that is not identified in paragraph (c) of
this AD.
(j) No Reporting Requirements
The reporting requirements specified in Turbomeca MSB No. 319 73
2080, Revision 1, dated February 13, 2004; Turbomeca MSB No. 319 73
2081, Revision 1, dated February 13, 2004; Turbomeca MSB No. 319 73
2082, Revision 1, dated February 13, 2004, Version C, dated July 31,
2008, and Version D, dated June 6, 2011; and Turbomeca MSB No. 319
73 2090, Original Issue, dated February 13, 2004, are not required
by this AD.
(k) Alternative Methods of Compliance (AMOCs)
(1) The Manager, ECO Branch, FAA, has the authority to approve
AMOCs for this AD, if requested using the procedures found in 14 CFR
39.19. In accordance with 14 CFR 39.19, send your request to your
principal inspector or local Flight Standards District Office, as
appropriate. If sending information directly to the manager of the
certification office, send it to the attention of the person
identified in paragraph (l)(1) of this AD. Information may be
emailed to: [email protected].
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
(l) Related Information
(1) For more information about this AD, contact Wego Wang,
Aviation Safety Engineer, ECO Branch, FAA, 1200 District Avenue,
Burlington, MA 01803; phone: (781) 238-7134; fax: (781) 238-7199;
email: [email protected].
(2) Refer to European Union Aviation Safety Agency (EASA) AD
2021-0088R1, dated July 26, 2021, for more information. You may
examine the EASA AD in the AD docket at https://www.regulations.gov
by searching for and locating Docket No. FAA-2021-0793.
(m) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless the AD specifies otherwise.
(3) The following service information was approved for IBR on
February 23, 2022.
(i) Turbomeca Mandatory Service Bulletin (MSB) No. 319 73 2082,
Version C, dated July 31, 2008.
(ii) Turbomeca MSB No. 319 73 2082, Version D, dated June 6,
2011.
(4) The following service information was approved for IBR on
June 29, 2005 (70 FR 34334, June 14, 2005).
(i) Turbomeca MSB No. 319 73 2080, Revision 1, dated February
13, 2004.
(ii) Turbomeca MSB No. 319 73 2081, Revision 1, dated February
13, 2004.
(iii) Turbomeca MSB No. 319 73 2082, Revision 1, dated February
13, 2004.
(iv) Turbomeca MSB No. 319 73 2090, Original Issue, dated
February 13, 2004.
(5) For Turbomeca service information identified in this AD,
contact Safran Helicopter Engines, S.A., Avenue du 1er Mai, 40220
Tarnos, France; phone: +33 (0) 5 59 74 45 00.
(6) You may view this service information at FAA, Airworthiness
Products Section, Operational Safety Branch, 1200 District Avenue,
Burlington, MA 01803. For information on the availability of this
material at the FAA, call (817) 222-5110.
(7) You may view this service information at the National
Archives and Records Administration (NARA). For information on the
availability of this material at NARA, email:
[email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.
Issued on December 17, 2021.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification
Service.
[FR Doc. 2022-00891 Filed 1-18-22; 8:45 am]
BILLING CODE 4910-13-P