[Federal Register Volume 86, Number 157 (Wednesday, August 18, 2021)]
[Proposed Rules]
[Pages 46164-46167]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-17196]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0667; Project Identifier MCAI-2021-00580-T]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus SAS Model A350-941 and -1041 airplanes. This 
proposed AD was prompted by a report that during type certification 
activity, it was identified that certain monitoring software was 
incorrectly implemented in the braking control system (BCS) 
certification standard. This proposed AD would require installing 
(updating) certain software for the braking and steering system, as 
specified in a European Union Aviation Safety Agency (EASA) AD, which 
is proposed for incorporation by reference. The FAA is proposing this 
AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by October 4, 
2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For material that will be incorporated by reference (IBR) in this 
AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221

[[Page 46165]]

8999 000; email [email protected]; internet www.easa.europa.eu. You 
may find this IBR material on the EASA website at https://ad.easa.europa.eu. You may view this IBR material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195. It is also available in the AD 
docket on the internet at https://www.regulations.gov by searching for 
and locating Docket No. FAA-2021-0667.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
0667; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, any comments received, and other information. The street 
address for Docket Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, Large 
Aircraft Section, International Validation Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3225; email 
[email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under ADDRESSES. Include ``Docket No. FAA-2021-0667; Project Identifier 
MCAI-2021-00580-T'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. The FAA 
will consider all comments received by the closing date and may amend 
the proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this proposed AD.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to Dan 
Rodina, Aerospace Engineer, Large Aircraft Section, International 
Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; 
telephone and fax 206-231-3225; email [email protected]. Any 
commentary that the FAA receives which is not specifically designated 
as CBI will be placed in the public docket for this rulemaking.

Background

    EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2021-0127, dated May 12, 2021 (EASA 
AD 2021-0127) (also referred to as the Mandatory Continuing 
Airworthiness Information, or the MCAI), to correct an unsafe condition 
for certain Airbus SAS Model A350-941 and -1041 airplanes.
    This proposed AD was prompted by a report that during type 
certification activity, it was identified that certain monitoring 
software was incorrectly implemented in the BCS certification standard. 
The FAA is proposing this AD to address in-service limitations related 
to the braking and steering system, which, under specific degraded 
conditions, could lead to a reduction in braking performance and 
potentially lead to a runway excursion, and result in damage to the 
airplane and injury to passengers. See the MCAI for additional 
background information.

Related Service Information Under 1 CFR Part 51

    EASA AD 2021-0127 describes procedures for installing (updating) 
serviceable software for the braking and steering system. Serviceable 
software includes BCS software (SW) standard (STD) S5B, wheel steering 
control system (WSCS) SW STD S5B, and landing gear extension and 
retraction system (LGERS) SW STD S5A. This material is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in the 
ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is proposing this AD because the FAA 
evaluated all the relevant information and determined the unsafe 
condition described previously is likely to exist or develop in other 
products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2021-0127 described previously, as incorporated by 
reference, except for any differences identified as exceptions in the 
regulatory text of this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA developed a process to use some civil aviation 
authority (CAA) ADs as the primary source of information for compliance 
with requirements for corresponding FAA ADs. The FAA has been 
coordinating this process with manufacturers and CAAs. As a result, the 
FAA proposes to incorporate EASA AD 2021-0127 by reference in the FAA 
final rule. This proposed AD would, therefore, require compliance with 
EASA AD 2021-0127 in its entirety through that incorporation, except 
for any differences identified as exceptions in the regulatory text of 
this proposed AD. Using common terms that are the same as the heading 
of a particular section in EASA AD 2021-0127 does not mean that 
operators need comply only with that section. For example, where the AD 
requirement refers to ``all required actions and compliance times,'' 
compliance with this AD requirement is not limited to the section 
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2021-
0127. Service information required by EASA AD 2021-0127 for compliance 
will be available at https://www.regulations.gov by searching for and 
locating Docket No. FAA-2021-0667 after the FAA final rule is 
published.

[[Page 46166]]

Costs of Compliance

    The FAA estimates that this proposed AD affects 17 airplanes of 
U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
              Labor cost                      Parts cost            Cost per product      Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Up to 4 work-hours x $85 per hour =    Up to $1,650...........  Up to $1,990...........  Up to $33,830.
 Up to $340.
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, some or all of the costs of this 
proposed AD may be covered under warranty, thereby reducing the cost 
impact on affected operators. The FAA does not control warranty 
coverage for affected operators. As a result, the FAA has included all 
known costs in the cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Airbus SAS: Docket No. FAA-2021-0667; Project Identifier MCAI-2021-
00580-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by October 4, 2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS Model A350-941 and -1041 
airplanes, certificated in any category, as identified in European 
Union Aviation Safety Agency (EASA) AD 2021-0127, dated May 12, 2021 
(EASA AD 2021-0127).

(d) Subject

    Air Transport Association (ATA) of America Code 32, Landing 
gear.

(e) Reason

    This AD was prompted by a report that during type certification 
activity, it was identified that certain monitoring software was 
incorrectly implemented in the braking control system (BCS) 
certification standard. The FAA is issuing this AD to address in-
service limitations related to the braking and steering system, 
which, under specific degraded conditions, could lead to a reduction 
in braking performance and potentially lead to a runway excursion, 
and result in damage to the airplane and injury to passengers.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2021-0127.

(h) Exceptions to EASA AD 2021-0127

    (1) Where EASA AD 2021-0127 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2021-0127 does not apply 
to this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or responsible Flight 
Standards Office, as appropriate. If sending information directly to 
the Large Aircraft Section, International Validation Branch, send it 
to the attention of the person identified in paragraph (j)(2) of 
this AD. Information may be emailed to: [email protected]. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
responsible Flight Standards Office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Airbus 
SAS's EASA Design Organization Approval (DOA). If approved by the 
DOA, the approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (i)(2) of this AD, if any service information contains 
procedures or tests that are identified as RC, those procedures and 
tests must be done to comply with this AD; any procedures or tests 
that are not identified as RC are recommended. Those procedures and 
tests that are not identified as RC may be deviated from using 
accepted methods in accordance with the operator's maintenance or 
inspection program without obtaining approval of an AMOC, provided 
the procedures and tests identified as RC can be done and the 
airplane can be put back in

[[Page 46167]]

an airworthy condition. Any substitutions or changes to procedures 
or tests identified as RC require approval of an AMOC.

(j) Related Information

    (1) For information about EASA AD 2021-0127 contact EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; internet www.easa.europa.eu. You 
may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195. This material may be 
found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-
2021-0667.
    (2) For more information about this AD, contact Dan Rodina, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3225; email [email protected].

    Issued on August 7, 2021.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2021-17196 Filed 8-17-21; 8:45 am]
BILLING CODE 4910-13-P