[Federal Register Volume 86, Number 114 (Wednesday, June 16, 2021)]
[Rules and Regulations]
[Pages 31905-31907]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-12516]



 ========================================================================
 Rules and Regulations
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains regulatory documents 
 having general applicability and legal effect, most of which are keyed 
 to and codified in the Code of Federal Regulations, which is published 
 under 50 titles pursuant to 44 U.S.C. 1510.
 
 The Code of Federal Regulations is sold by the Superintendent of Documents. 
 
 ========================================================================
 

  Federal Register / Vol. 86, No. 114 / Wednesday, June 16, 2021 / 
Rules and Regulations  

[[Page 31905]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2021-0446; Project Identifier 2018-SW-029-AD; Amendment 
39-21590; AD 2021-12-03]
RIN 2120-AA64


Airworthiness Directives; Leonardo S.p.a.

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Leonardo S.p.a. Model AW189 helicopters. This AD was prompted 
by a report of the bubble window departing from the helicopter during 
flight. This AD requires installation of a new improved bubble window 
kit, as specified in a European Aviation Safety Agency (now the 
European Union Aviation Safety Agency) (EASA) AD, which is incorporated 
by reference. The FAA is issuing this AD to address the unsafe 
condition on these products.

DATES: This AD becomes effective July 1, 2021.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of July 1, 
2021.
    The FAA must receive comments on this AD by August 2, 2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For material incorporated by reference (IBR) in this AD, contact 
the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; phone: +49 
221 8999 000; email: [email protected]; internet: www.easa.europa.eu. 
You may find this material on the EASA website at https://ad.easa.europa.eu. You may view this material at the FAA, Office of the 
Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 6N-321, 
Fort Worth, TX 76177. For information on the availability of this 
material at the FAA, call 817-222-5110. It is also available in the AD 
docket on the internet at https://www.regulations.gov by searching for 
and locating Docket No. FAA-2021-0446.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-
0446; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this AD, any comments received, and other information. The street 
address for Docket Operations is listed above. Comments will be 
available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Andrea Jimenez, Aerospace Engineer, 
COS Program Management Section, Operational Safety Branch, Compliance & 
Airworthiness Division, FAA, 1600 Stewart Avenue, Suite 410, Westbury, 
NY 11590; phone: 516-228-7330; fax: 516-794-5531; email: [email protected].

SUPPLEMENTARY INFORMATION:

Background

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2018-0082, dated April 11, 2018 
(EASA AD 2018-0082) (also referred to as the Mandatory Continuing 
Airworthiness Information, or the MCAI), to correct an unsafe condition 
for Leonardo S.p.a. Model AW189 helicopters, if equipped with bubble 
windows kit part number 8G5620F00111.
    This AD was prompted by a report of a bubble window departing from 
the helicopter during flight. The FAA is issuing this AD to address 
degradation of the installation of the bubble windows, which could 
cause loss of a bubble window during flight, possibly resulting in 
damage to the helicopter and injury to persons on the ground. See the 
MCAI for additional background information.

Related IBR Material Under 1 CFR Part 51

    EASA AD 2018-0082 specifies procedures for, among other actions, 
modifying the left-hand and right-hand bubble windows with an improved 
bubble window kit. This material is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this AD after evaluating all 
pertinent information and determining that the unsafe condition exists 
and is likely to exist or develop on other products of the same type 
design.

Requirements of This AD

    This AD requires accomplishing the actions specified in EASA AD 
2018-0082, described previously, as incorporated by reference, except 
for any differences identified as exceptions in the regulatory text of 
this AD and except as discussed under ``Differences Between this AD and 
the MCAI.''

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding FAA ADs. The FAA has 
since coordinated with other manufacturers and civil aviation 
authorities (CAAs) to

[[Page 31906]]

use this process. As a result, EASA AD 2018-0082 is incorporated by 
reference in this final rule. This AD, therefore, requires compliance 
with EASA AD 2018-0082 in its entirety, through that incorporation, 
except for any differences identified as exceptions in the regulatory 
text of this AD. Using common terms that are the same as the heading of 
a particular section in the EASA AD does not mean that operators need 
comply only with that section. For example, where the AD requirement 
refers to ``all required actions and compliance times,'' compliance 
with this AD requirement is not limited to the section titled 
``Required Action(s) and Compliance Time(s)'' in the EASA AD. Service 
information specified in EASA AD 2018-0082 that is required for 
compliance with EASA AD 2018-0082 is available on the internet at 
https://www.regulations.gov by searching for and locating Docket No. 
FAA-2021-0446.

Differences Between This AD and the MCAI

    The requirements specified in paragraphs (1), (2), (3) and (5) of 
EASA AD 2018-0082 do not apply to this AD.

FAA's Justification and Determination of the Effective Date

    Section 553(b)(3)(B) of the Administrative Procedure Act (5 U.S.C.) 
authorizes agencies to dispense with notice and comment procedures for 
rules when the agency, for ``good cause'' finds that those procedures 
are ``impracticable, unnecessary, or contrary to the public interest.'' 
Under this section, an agency, upon finding good cause, may issue a 
final rule without seeking comment prior to the rulemaking.
    There are currently no domestic operators of these products. 
Therefore, the FAA finds that notice and opportunity for prior public 
comment are unnecessary and that good cause exists pursuant to 5 U.S.C. 
553(d) for making this amendment effective in less than 30 days.

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this AD. Send your comments to an address listed under 
ADDRESSES. Include ``Docket No. FAA-2021-0446; Project Identifier 2018-
SW-029-AD'' at the beginning of your comments. The most helpful 
comments reference a specific portion of the AD, explain the reason for 
any recommended change, and include supporting data. The FAA will 
consider all comments received by the closing date and may amend this 
AD because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this AD.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this AD contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this AD, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this AD. Submissions containing CBI should be sent to Andrea 
Jimenez, Aerospace Engineer, Airframe and Propulsion Section, FAA, New 
York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
phone: 516-228-7330; fax: 516-794-5531; email: [email protected]. 
Any commentary that the FAA receives that is not specifically 
designated as CBI will be placed in the public docket for this 
rulemaking.

Regulatory Flexibility Act (RFA)

    The requirements of the RFA do not apply when an agency finds good 
cause pursuant to 5 U.S.C. 553 to adopt a rule without prior notice and 
comment. Because the FAA has determined that it has good cause to adopt 
this rule without notice and comment, RFA analysis is not required.

Costs of Compliance

    Currently, there are no affected U.S.-registered helicopters. If an 
affected helicopter is imported and placed on the U.S. Register in the 
future, the FAA provides the following cost estimates to comply with 
this AD:

                  Estimated Costs for Required Actions
------------------------------------------------------------------------
                                                             Cost per
              Labor cost                   Parts cost        product
------------------------------------------------------------------------
32 work-hours x $85 per hour = $2,720.          $2,000           $4,720
------------------------------------------------------------------------

    According to the manufacturer, some or all of the costs of this AD 
may be covered under warranty, thereby reducing the cost impact on 
affected individuals. The FAA does not control warranty coverage for 
affected individuals. As a result, the FAA has included all known costs 
in the cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this AD would not have federalism 
implications under Executive Order 13132. This AD would not have a 
substantial direct effect on the States, on the relationship between 
the national Government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this regulation:

[[Page 31907]]

    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866, and
    (2) Will not affect intrastate aviation in Alaska.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2021-12-03 Leonardo S.p.a.: Amendment 39-21590; Docket No. FAA-2021-
0446; Project Identifier 2018-SW-029-AD.

(a) Effective Date

    This airworthiness directive (AD) becomes effective July 1, 
2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Leonardo S.p.a. Model AW189 helicopters, 
certificated in any category, equipped with bubble windows kit Part 
Number (P/N) 8G5620F00111, as identified in European Aviation Safety 
Agency (now European Union Aviation Safety Agency) (EASA) AD 2018-
0082, dated April 11, 2018 (EASA AD 2018-0082).

(d) Subject

    Joint Aircraft System Component (JASC) Code 5600, Window/
Windshield System.

(e) Unsafe Condition

    This AD was prompted by a report of a bubble window departing 
from the helicopter during flight. The FAA is issuing this AD to 
address degradation of the installation of the bubble windows, which 
could cause loss of a bubble window during flight, possibly 
resulting in damage to the helicopter and injury to persons on the 
ground.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2018-0082.

(h) Exceptions to EASA AD 2018-0082

    (1) Where EASA AD 2018-0082 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2018-0082 does not apply 
to this AD.
    (3) Where the service information referenced in EASA AD 2018-
0082 specifies to discard certain parts, this AD requires removing 
those parts from service.
    (4) Where EASA AD 2018-0082 refers to flight hours (FH), this AD 
requires using hours time-in-service.
    (5) The requirements specified in paragraphs (1), (2), (3) and 
(5) of EASA AD 2018-0082 do not apply to this AD.

(i) No Reporting Requirement

    Although the service information referenced in EASA AD 2018-0082 
specifies to submit certain information to the manufacturer, this AD 
does not include that requirement.

 (j) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, International Validation Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the manager of the International Validation Branch, send 
it to the attention of the person identified in paragraph (k) of 
this AD. Information may be emailed to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.

 (k) Related Information

    For more information about this AD, contact Andrea Jimenez, 
Aerospace Engineer, COS Program Management Section, Operational 
Safety Branch, Compliance & Airworthiness Division, FAA, 1600 
Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 516-228-7330; 
fax: 516-794-5531; email: [email protected].

 (l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Aviation Safety Agency (EASA) AD 2018-0082, dated 
April 11, 2018.
    (ii) [Reserved]
    (3) For EASA AD 2018-0082, contact the EASA, Konrad-Adenauer-
Ufer 3, 50668 Cologne, Germany; phone: +49 221 8999 000; email: 
[email protected]; internet: www.easa.europa.eu. You may find this 
EASA AD on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this service information at the FAA, Office of 
the Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 
6N-321, Fort Worth, TX 76177. For information on the availability of 
this material at the FAA, call 817-222-5110. This material may be 
found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-
2021-0446.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on June 9, 2021.
Ross Landes,
Deputy Director for Regulatory Operations, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2021-12516 Filed 6-15-21; 8:45 am]
BILLING CODE 4910-13-P