[Federal Register Volume 86, Number 12 (Thursday, January 21, 2021)]
[Proposed Rules]
[Pages 6269-6271]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2021-01160]


 ========================================================================
 Proposed Rules
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains notices to the public of 
 the proposed issuance of rules and regulations. The purpose of these 
 notices is to give interested persons an opportunity to participate in 
 the rule making prior to the adoption of the final rules.
 
 ========================================================================
 

  Federal Register / Vol. 86, No. 12 / Thursday, January 21, 2021 / 
Proposed Rules  

[[Page 6269]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-1166; Project Identifier AD-2020-00906-T]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain The Boeing Company Model 737-9 airplanes. This proposed AD 
was prompted by a report of missing sealant on the left and right wing 
leading edge outboard blowout door. This proposed AD would require 
doing a fluid seal contact inspection and a detailed inspection for 
missing sealant on the blowout door and applying sealant if necessary. 
The FAA is proposing this AD to address the unsafe condition on these 
products.

DATES: The FAA must receive comments on this proposed AD by March 8, 
2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; internet https://www.myboeingfleet.com. You may 
view this referenced service information at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., Des 
Moines, WA. For information on the availability of this material at the 
FAA, call 206-231-3195. It is also available on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
1166.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
1166; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, any comments received, and other information. The street 
address for Docket Operations is listed above.

FOR FURTHER INFORMATION CONTACT: Chris Baker, Aerospace Engineer, 
Propulsion Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des 
Moines, WA 98198; phone and fax: 206-231-3552; email: 
[email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2020-1166; 
Project Identifier AD-2020-00906-T'' at the beginning of your comments. 
The most helpful comments reference a specific portion of the proposal, 
explain the reason for any recommended change, and include supporting 
data. The FAA will consider all comments received by the closing date 
and may amend this proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this proposed AD.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to Chris 
Baker, Aerospace Engineer, Propulsion Section, FAA, Seattle ACO Branch, 
2200 South 216th St., Des Moines, WA 98198; phone and fax: 206-231-
3552; email: [email protected]. Any commentary that the FAA 
receives which is not specifically designated as CBI will be placed in 
the public docket for this rulemaking.

Background

    The FAA proposes to adopt a new AD for The Boeing Company Model 
737-9 airplanes having line numbers 6834, 6852, 6872, 6899, 6917, 6935, 
7096, 7173, 7196, 7201, 7208, 7216, 7246, 7253, 7261, 7268, 7306, 7316, 
7338, 7348, 7361, 7384, 7388, 7394, and 7428. The FAA received a report 
indicating that the application of sealant on the left wing and right 
wing leading edge outboard blowout door was missed during the airplane 
manufacturing process on some Model 737-9 airplanes. The missing 
sealant is intended to act as a fuel barrier. In the event of a 
substantial fuel leak from the wing box, missing sealant could result 
in an unintended drain path allowing fuel to come into contact with the 
engine. This condition, if not addressed, could lead to a large ground 
fire.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Boeing Alert Requirements Bulletin 737-57A1350 RB, 
dated April 23, 2020. The service

[[Page 6270]]

information specifies procedures for doing a fluid seal contact 
inspection and a detailed inspection of the left and right wing leading 
edge outboard blowout door, at the inboard and outboard ends of the 
hinge, for missing sealant and applying sealant, if necessary.
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination

    The FAA is issuing this NPRM after determining the unsafe condition 
described previously is likely to exist or develop in other products of 
the same type design.

Proposed AD Requirements in This NPRM

    This proposed AD would require accomplishment of the actions 
identified in Boeing Alert Requirements Bulletin 737-57A1350 RB, dated 
April 23, 2020, described previously, except for any differences 
identified as exceptions in the regulatory text of this proposed AD.
    For information on the procedures and compliance times, see this 
service information at https://www.regulations.gov by searching for and 
locating Docket No. FAA-2020-1166.

Costs of Compliance

    The FAA estimates that this AD, if adopted as proposed, would 
affect 14 airplanes of U.S. registry. The FAA estimates the following 
costs to comply with this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
               Action                        Labor cost           Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
Inspections.........................  4 work-hours x $85 per               $0             $340           $4,760
                                       hour = $340.
----------------------------------------------------------------------------------------------------------------

    The FAA estimates the following costs to do any necessary repairs 
that would be required based on the results of the proposed 
inspections. The FAA has no way of determining the number of aircraft 
that might need these on-condition actions:

                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
           Labor cost                 Parts cost       Cost per product
------------------------------------------------------------------------
Up to 4 work-hours x $85 per      Up to $100........  Up to $440.
 hour = Up to $340.
------------------------------------------------------------------------

    The FAA has included all known costs in this cost estimate. 
According to the manufacturer, however, some or all of the costs of 
this proposed AD may be covered under warranty, thereby reducing the 
cost impact on affected operators.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Would not affect intrastate aviation in Alaska, and
    (3) Would not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

The Boeing Company: Docket No. FAA-2020-1166; Project Identifier AD-
2020-00906-T.

(a) Comments Due Date

    The FAA must receive comments on this airworthiness directive 
(AD) by March 8, 2021.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 737-9 airplanes, 
certificated in any category, as identified in Boeing Alert 
Requirements Bulletin 737-57A1350 RB, dated April 23, 2020.

(d) Subject

    Air Transport Association (ATA) of America Code 57, Wings.

(e) Unsafe Condition

    This AD was prompted by a report of missing sealant on the left 
and right wing

[[Page 6271]]

leading edge outboard blowout door. The FAA is issuing this AD to 
address the missing sealant, which is intended to act as a fuel 
barrier. In the presence of a substantial fuel leak from the wing 
box, the unintended drain path could allow fuel to come into contact 
with the engine. This condition, if not addressed, could lead to a 
large ground fire.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Except as specified by paragraph (h) of this AD, at the 
applicable times specified in the Compliance paragraph of Boeing 
Alert Requirements Bulletin 737-57A1350 RB, dated April 23, 2020, do 
all applicable actions identified in, and in accordance with, the 
Accomplishment Instructions of Boeing Alert Requirements Bulletin 
737-57A1350 RB, dated April 23, 2020.
    Note 1 to paragraph (g): Guidance for accomplishing the actions 
required by this AD can be found in Boeing Alert Service Bulletin 
737-57A1350, dated April 23, 2020, which is referred to in Boeing 
Alert Requirements Bulletin 737-57A1350 RB, dated April 23, 2020.

(h) Exception to Service Information Specifications

    Where Boeing Alert Requirements Bulletin 737-57A1350 RB, dated 
April 23, 2020, refers to ``the Original Issue date of Requirements 
Bulletin 737-57A1350 RB,'' this AD requires using ``the effective 
date of this AD.''

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO Branch, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request 
to your principal inspector or responsible Flight Standards Office, 
as appropriate. If sending information directly to the manager of 
the certification office, send it to the attention of the person 
identified in paragraph (j)(1) of this AD. Information may be 
emailed to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the responsible Flight Standards Office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by The Boeing Company Organization Designation 
Authorization (ODA) that has been authorized by the Manager, Seattle 
ACO Branch, FAA, to make those findings. To be approved, the repair 
method, modification deviation, or alteration deviation must meet 
the certification basis of the airplane, and the approval must 
specifically refer to this AD.

(j) Related Information

    (1) For more information about this AD, contact Chris Baker, 
Aerospace Engineer, Propulsion Section, FAA, Seattle ACO Branch, 
2200 South 216th St., Des Moines, WA 98198; phone and fax: 206-231-
3552; email: [email protected].
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; internet https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA, Airworthiness Products Section, Operational 
Safety Branch, 2200 South 216th St., Des Moines, WA. For information 
on the availability of this material at the FAA, call 206-231-3195.

    Issued on December 17, 2020.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2021-01160 Filed 1-19-21; 8:45 am]
BILLING CODE 4910-13-P