[Federal Register Volume 85, Number 238 (Thursday, December 10, 2020)]
[Proposed Rules]
[Pages 79440-79443]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-26942]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-1115; Project Identifier MCAI-2020-01230-T]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus SAS Model A330-200

[[Page 79441]]

Freighter series airplanes. This proposed AD was prompted by a 
determination that new or more restrictive airworthiness limitations 
are necessary. This proposed AD would require revising the existing 
maintenance or inspection program, as applicable, to incorporate new or 
more restrictive airworthiness limitations, as specified in a European 
Union Aviation Safety Agency (EASA) AD, which is proposed for 
incorporation by reference. The FAA is proposing this AD to address the 
unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by January 25, 
2021.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For material that will be incorporated by reference (IBR) in this 
AD, contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221 8999 000; email [email protected]; internet 
www.easa.europa.eu. You may find this IBR material on the EASA website 
at https://ad.easa.europa.eu. You may view this IBR material at the 
FAA, Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability of 
this material at the FAA, call 206-231-3195. It is also available in 
the AD docket on the internet at https://www.regulations.gov by 
searching for and locating Docket No. FAA-2020-1115.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
1115; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, any comments received, and other information. The street 
address for Docket Operations is listed above. Comments will be 
available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer, 
Large Aircraft Section, International Validation Branch, FAA, 2200 
South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3229; 
email [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2020-1115; 
Project Identifier MCAI-2020-01230-T'' at the beginning of your 
comments. The most helpful comments reference a specific portion of the 
proposal, explain the reason for any recommended change, and include 
supporting data. The FAA will consider all comments received by the 
closing date and may amend the proposal because of those comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments received, without change, to 
https://www.regulations.gov, including any personal information you 
provide. The agency will also post a report summarizing each 
substantive verbal contact received about this proposed AD.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this NPRM contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this NPRM, it is important that you clearly designate the submitted 
comments as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this NPRM. Submissions containing CBI should be sent to 
Vladimir Ulyanov, Aerospace Engineer, Large Aircraft Section, 
International Validation Branch, FAA, 2200 South 216th St., Des Moines, 
WA 98198; telephone and fax 206-231-3229; email 
[email protected]. Any commentary that the FAA receives which is 
not specifically designated as CBI will be placed in the public docket 
for this rulemaking.

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2020-0190, dated August 27, 2020 
(also referred to as the Mandatory Continuing Airworthiness 
Information, or the MCAI) (EASA AD 2020-0190), to correct an unsafe 
condition for all Airbus SAS Model A330-200 Freighter series airplanes, 
and Model A340-213 and -313 airplanes. Airplanes with an original 
airworthiness certificate or original export certificate of 
airworthiness issued after June 29, 2020 must comply with the 
airworthiness limitations specified as part of the approved type design 
and referenced on the type certificate data sheet; this AD therefore 
does not include those airplanes in the applicability.
    EASA AD 2020-0190 specifies that it requires a task (limitation) 
already required by EASA AD 2018-0034 (which corresponds to FAA AD 
2018-23-14, Amendment 39-19501 (83 FR 60754, November 27, 2018) (AD 
2018-23-14)) and invalidates prior instructions for that task. This 
proposed AD would terminate the limitation for the nose landing gear 
lower torque link having part number D64001, as required by paragraph 
(g) of AD 2018-23-14, for Model A330-223F and -243F airplanes only.
    This proposed AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
proposing this AD to address fatigue cracking, accidental damage, or 
corrosion in principal structural elements, and possible failure of 
certain life limited parts, which could result in reduced structural 
integrity of the airplane. See the MCAI for additional background 
information.

Related Service Information Under 1 CFR Part 51

    EASA AD 2020-0190 describes new or more restrictive airworthiness 
limitations for airplane structures and safe life limits.
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation

[[Page 79442]]

in the United States. Pursuant to the FAA's bilateral agreement with 
the State of Design Authority, the FAA has been notified of the unsafe 
condition described in the MCAI referenced above. The FAA is proposing 
this AD because the FAA has evaluated all pertinent information and 
determined an unsafe condition exists and is likely to exist or develop 
on other products of the same type design.

Proposed AD Requirements

    This proposed AD would require revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations, which are specified in EASA AD 
2020-0190 described previously, as incorporated by reference. Any 
differences with EASA AD 2020-0190 are identified as exceptions in the 
regulatory text of this AD and discussed under ``Differences Between 
this Proposed AD and the MCAI.''
    This proposed AD would require revisions to certain operator 
maintenance documents to include new actions (e.g., inspections). 
Compliance with these actions is required by 14 CFR 91.403(c). For 
airplanes that have been previously modified, altered, or repaired in 
the areas addressed by this proposed AD, the operator may not be able 
to accomplish the actions described in the revisions. In this 
situation, to comply with 14 CFR 91.403(c), the operator must request 
approval for an alternative method of compliance according to paragraph 
(k)(1) of this proposed AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding FAA ADs. The FAA has 
since coordinated with other manufacturers and civil aviation 
authorities (CAAs) to use this process. As a result, EASA AD 2020-0190 
will be incorporated by reference in the FAA final rule. This proposed 
AD would, therefore, require compliance with EASA AD 2020-0190 in its 
entirety, through that incorporation, except for any differences 
identified as exceptions in the regulatory text of this proposed AD. 
Using common terms that are the same as the heading of a particular 
section in the EASA AD does not mean that operators need comply only 
with that section. For example, where the AD requirement refers to 
``all required actions and compliance times,'' compliance with this AD 
requirement is not limited to the section titled ``Required Action(s) 
and Compliance Time(s)'' in the EASA AD.
    Service information specified in EASA AD 2020-0190 that is required 
for compliance with EASA AD 2020-0190 will be available on the internet 
at https://www.regulations.gov by searching for and locating Docket No. 
FAA-2020-1115 after the FAA final rule is published.

Airworthiness Limitation ADs Using the New Process

    The FAA's process of incorporating by reference MCAI ADs as the 
primary source of information for compliance with corresponding FAA ADs 
has been limited to certain MCAI ADs (primarily those with service 
bulletins as the primary source of information for accomplishing the 
actions required by the FAA AD). However, the FAA is now expanding the 
process to include MCAI ADs that require a change to airworthiness 
limitation documents, such as airworthiness limitation sections.
    For these ADs that incorporate by reference an MCAI AD that changes 
airworthiness limitations, the FAA requirements are unchanged. 
Operators must revise the existing maintenance or inspection program, 
as applicable, to incorporate the information specified in the new 
airworthiness limitation document. The airworthiness limitations must 
be followed according to 14 CFR 91.403(c) and 91.409(e).
    The previous format of the airworthiness limitation ADs included a 
paragraph that specified that no alternative actions (e.g., 
inspections) or intervals may be used unless the actions and intervals 
are approved as an alternative method of compliance (AMOC) in 
accordance with the procedures specified in the AMOCs paragraph under 
``Other FAA Provisions.'' This new format includes a ``New Provisions 
for Alternative Actions and Intervals'' paragraph that does not 
specifically refer to AMOCs, but operators may still request an AMOC to 
use an alternative action or interval.

Differences Between This Proposed AD and the MCAI

    This proposed AD does not include the Model A340-213 and -313 
airplanes that are specified in the MCAI. Instead, the FAA has added 
the MCAI to the required airworthiness actions list (RAAL) for the 
Model A340 airplanes.

Costs of Compliance

    The FAA estimates that this proposed AD affects 6 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this 
proposed AD:
    The FAA has determined that revising the existing maintenance or 
inspection program takes an average of 90 work-hours per operator, 
although the agency recognizes that this number may vary from operator 
to operator. Since operators incorporate maintenance or inspection 
program changes for their affected fleet(s), the FAA has determined 
that a per-operator estimate is more accurate than a per-airplane 
estimate. Therefore, the agency estimates the average total cost per 
operator to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA has determined that this proposed AD would not have 
federalism implications under Executive Order 13132. This proposed AD 
would not have a substantial direct effect on the States, on the 
relationship between the national Government and the States, or on the 
distribution of power and responsibilities among the various levels of 
government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

[[Page 79443]]

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

Airbus SAS: Docket No. FAA-2020-1115; Project Identifier MCAI-2020-
01230-T.

(a) Comments Due Date

    The FAA must receive comments by January 25, 2021.

(b) Affected Airworthiness Directives (ADs)

    The AD affects AD 2018-23-14, Amendment 39-19501 (83 FR 60754, 
November 27, 2018) (AD 2018-23-14).

(c) Applicability

    This AD applies to Airbus SAS Model A330-223F and -243F 
airplanes, certificated in any category, with an original 
airworthiness certificate or original export certificate of 
airworthiness issued on or before June 29, 2020.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Reason

    This AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
issuing this AD to address fatigue cracking, accidental damage, or 
corrosion in principal structural elements, and possible failure of 
certain life limited parts, which could result in reduced structural 
integrity of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Union Aviation Safety Agency (EASA) AD 
2020-0190, dated August 27, 2020 (EASA AD 2020-0190).

(h) Exceptions to EASA AD 2020-0190

    (1) The requirements specified in paragraph (1) of EASA AD 2020-
0190 do not apply to this AD.
    (2) Paragraph (2) of EASA AD 2020-0190 specifies revising ``the 
approved AMP'' within 12 months after its effective date, but this 
AD requires revising the existing maintenance or inspection program, 
as applicable, to incorporate the ``limitations'' specified in 
paragraph (2) of EASA AD 2020-0190 within 90 days after the 
effective date of this AD.
    (3) The initial compliance time for doing the tasks specified in 
paragraph (2) of EASA AD 2020-0190 is on or before the applicable 
``limitations'' specified in paragraph (2) of EASA AD 2020-0190, or 
within 90 days after the effective date of this AD, whichever occurs 
later.
    (4) The provision specified in paragraph (3) of EASA AD 2020-
0190 does not apply to this AD.
    (5) The ``Remarks'' section of EASA AD 2020-0190 does not apply 
to this AD.

(i) Provisions for Alternative Actions or Intervals

    After the existing maintenance or inspection program has been 
revised as required by paragraph (g) of this AD, no alternative 
actions (e.g., inspections) or intervals are allowed unless they are 
approved as specified in the provisions of the ``Ref. Publications'' 
section of EASA AD 2020-0190.

(j) Terminating Action for Certain Requirements of AD 2018-23-14

    Accomplishing the revision required by this AD terminates the 
limitation for the nose landing gear lower torque link having part 
number D64001, as required by paragraph (g) of AD 2018-23-14, for 
Model A330-223F and -243F airplanes only.

(k) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the Large Aircraft Section, International Validation 
Branch, send it to the attention of the person identified in 
paragraph (l)(2) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office/
certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Airbus 
SAS's EASA Design Organization Approval (DOA). If approved by the 
DOA, the approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): Except as required by 
paragraph (k)(2) of this AD, if any service information contains 
procedures or tests that are identified as RC, those procedures and 
tests must be done to comply with this AD; any procedures or tests 
that are not identified as RC are recommended. Those procedures and 
tests that are not identified as RC may be deviated from using 
accepted methods in accordance with the operator's maintenance or 
inspection program without obtaining approval of an AMOC, provided 
the procedures and tests identified as RC can be done and the 
airplane can be put back in an airworthy condition. Any 
substitutions or changes to procedures or tests identified as RC 
require approval of an AMOC.

(l) Related Information

    (1) For information about EASA AD 2020-0190, contact the EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; internet www.easa.europa.eu. You 
may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195. This material may be 
found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-
2020-1115.
    (2) For more information about this AD, contact Vladimir 
Ulyanov, Aerospace Engineer, Large Aircraft Section, International 
Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; 
telephone and fax 206-231-3229; email [email protected].

    Issued on December 3, 2020.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2020-26942 Filed 12-9-20; 8:45 am]
BILLING CODE 4910-13-P