[Federal Register Volume 85, Number 217 (Monday, November 9, 2020)]
[Rules and Regulations]
[Pages 71244-71246]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-24805]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-0719; Project Identifier 2019-CE-041-AD; Amendment 
39-21313; AD 2020-22-17]
RIN 2120-AA64


Airworthiness Directives; Pilatus Aircraft Ltd. Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Pilatus Aircraft Ltd. (Pilatus) Model PC-24 airplanes. This AD 
results from mandatory continuing airworthiness information (MCAI) 
originated by an aviation authority of another country to identify and 
correct an unsafe condition on an aviation product. The MCAI identifies 
the unsafe condition as movement of the aft fuel pipe within the 
coupling, which can cause damage to the O-rings and lead to a fuel 
leak, fuel fire or explosion, and consequent loss of control of the 
airplane. This AD requires replacing and prohibits installing affected 
parts. The FAA is issuing this AD to address the unsafe condition on 
these products.

DATES: This AD is effective December 14, 2020.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of December 14, 
2020.

ADDRESSES: For service information identified in this final rule, 
contact Pilatus Aircraft Ltd., Customer Support General Aviation, CH-
6371 Stans, Switzerland, telephone: +41 848 24 7 365, 
aircraft.com">techsupport.ch@pilatus-aircraft.com, https://www.pilatus-aircraft.com. 
You may view this service information at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 901 Locust, Kansas City, 
MO 64106. For information on the availability of this material at the 
FAA, call 816-329-4148. It is also available on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
0719.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
0719; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this final rule, the mandatory continuing airworthiness information 
(MCAI), any comments received, and other information. The address for 
Docket Operations is U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Doug Rudolph, Aerospace Engineer, FAA, 
General Aviation & Rotorcraft Section, International Validation Branch, 
901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 
329-4059; fax: (816) 329-4090; email: [email protected].

SUPPLEMENTARY INFORMATION:

Discussion

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to Pilatus Model PC-24 
airplanes with a certain part-numbered flexible saddle clamp installed 
between frame 34 and 36. The NPRM published in the Federal Register on 
July 30, 2020 (85 FR 45810). The NPRM proposed to require actions to 
correct the unsafe condition on the specified products and was prompted 
by MCAI originated by the European Union Aviation Safety Agency (EASA), 
which is the Technical Agent for the Member States of the European 
Union. EASA issued AD No. 2019-0240, dated September 25, 2019 (referred 
to after this as ``the MCAI''), which states:

    An occurrence was reported where, during maintenance, when 
system pressure was applied to a motive-flow fuel pipe, the aft fuel 
pipe was found to move to the end stop within the coupling. When 
system pressure was released, the aft fuel pipe returned to its 
point of origin. This movement can cause damage to the O-rings.
    This condition, if not corrected, could lead to a fuel leak and 
consequently a fuel contamination of the rear fuselage, which, in 
combination with an ignition source in this

[[Page 71245]]

area, could possibly result in a fuel fire or fuel vapour explosion 
and consequent loss of the aeroplane.
    To address this potential unsafe condition, Pilatus issued the 
[service bulletin] SB to provide modification instructions.
    For the reason described above, this [EASA] AD requires 
replacement of affected parts with serviceable parts, as defined in 
this AD, and prohibits (re-) installation of affected parts.

    You may examine the MCAI on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
0719.

Comments

    The FAA gave the public the opportunity to participate in 
developing this final rule. The FAA received no comments on the NPRM or 
on the determination of the cost to the public.

Conclusion

    The FAA reviewed the relevant data and determined that air safety 
and the public interest require adopting this final rule as proposed.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Pilatus PC-24 Service Bulletin No. 28-002, dated 
May 3, 2019. The service information contains procedures for replacing 
the two flexible saddle clamps on the left-hand (LH) motive-flow fuel 
pipe and the two flexible saddle clamps on the right-hand (RH) motive-
flow fuel pipe with fixed saddle clamps. This service information also 
contains procedures for replacing the four O-rings on the LH and RH 
motive-flow fuel pipes. This service information is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in the 
ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD will affect 16 products of U.S. 
registry. The FAA also estimates that it will take about 7 work-hours 
per product to comply with the requirements of this AD. The average 
labor rate is $85 per work-hour. Required parts will cost about $5,000 
per product.
    Based on these figures, the FAA estimates the cost of the AD on 
U.S. operators will be $89,520 or $5,595 per product.
    According to the manufacturer, all or some of the costs of this AD 
may be covered under warranty, thereby reducing the cost impact on 
affected individuals. The FAA does not control warranty coverage for 
affected individuals. As a result, the FAA has included all costs in 
this cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive:

2020-22-17 Pilatus Aircraft Ltd.: Amendment 39-21313; Docket No. 
FAA-2020-0719; Project Identifier 2019-CE-041-AD.

(a) Effective Date

    This airworthiness directive (AD) is effective December 14, 
2020.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Pilatus Aircraft Ltd. Model PC-24 airplanes, 
all serial numbers, certificated in any category, with a flexible 
saddle clamp part number (P/N) 946.33.22.004 installed between frame 
34 and 36.

(d) Subject

    Joint Aircraft System Component (JASC) Code 2800: Fuel.

(e) Reason

    This AD was prompted by an occurrence of movement of the aft 
fuel pipe within the coupling when system pressure was applied. This 
movement can cause damage to the O-rings, which could lead to a fuel 
leak and fuel contamination of the rear fuselage. The FAA is issuing 
this AD to prevent a fuel fire or fuel vapor explosion with 
consequent loss of airplane control.

(f) Actions and Compliance

    Unless already done, do the following actions in accordance with 
the applicable compliance times:
    (1) Within 3 months after the effective date of this AD, replace 
each flexible saddle clamp with a fixed saddle clamp with P/N 
946.33.21.933, align the left-hand (LH) and right-hand (RH) motive-
flow fuel pipes, and test the LH and RH motive-flow fuel pipe for 
leaks in accordance with the Accomplishment Instructions, sections 
3.B and 3.C, of Pilatus PC-24 Service Bulletin No. 28-002, dated May 
3, 2019.
    (2) As of the effective date of this AD, do not install a 
flexible saddle clamp with P/N 946.33.22.004 between frame 34 and 36 
on any airplane.

(g) Alternative Methods of Compliance (AMOCs)

    The Manager, International Validation Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. Send information to Doug Rudolph, 
Aerospace Engineer, FAA, General Aviation & Rotorcraft Section, 
International Validation Branch, 901 Locust, Room 301, Kansas City, 
Missouri 64106; telephone: (816) 329-4059; fax: (816) 329-4090; 
email: [email protected]. Before using any approved AMOC on any 
airplane to which the AMOC applies, notify your appropriate 
principal inspector (PI) in the FAA Flight Standards District Office 
(FSDO), or lacking a PI, your local FSDO.

(h) Related Information

    Refer to European Union Aviation Safety Agency (EASA) AD No. 
2019-0240, dated September 25, 2019, for more information. You may 
examine the EASA AD in the AD

[[Page 71246]]

docket on the internet at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2020-0719.

(i) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the service information listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Pilatus PC-24 Service Bulletin No. 28-002, dated May 3, 
2019.
    (ii) [Reserved]
    (3) For Pilatus Aircraft Ltd. service information identified in 
this AD, contact Pilatus Aircraft Ltd., Customer Technical Support 
(MCC), P.O. Box 992, CH-6371 Stans, Switzerland; telephone: +41 
(0)41 619 67 74; fax: +41 (0)41 619 67 73; email: 
aircraft.com">techsupport@pilatus-aircraft.com; internet: https://www.pilatus-aircraft.com/en.
    (4) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 901 
Locust, Kansas City, Missouri. For information on the availability 
of this material at the FAA, call 816-329-4148.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, email: [email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on October 22, 2020.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2020-24805 Filed 11-6-20; 8:45 am]
BILLING CODE 4910-13-P