[Federal Register Volume 85, Number 165 (Tuesday, August 25, 2020)]
[Rules and Regulations]
[Pages 52254-52257]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-18488]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-0777; Project Identifier MCAI-2020-01071-T; 
Amendment 39-21217; AD 2020-17-12]
RIN 2120-AA64


Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for 
certain Dassault Aviation Model MYSTERE-FALCON 900, FALCON 900EX, 
FALCON 2000, and FALCON 2000EX airplanes. This AD was prompted by 
reports of loose or missing nuts on the pilot and co-pilot ventral seat 
belt attachment points. This AD requires a detailed inspection of 
certain seat belt attaching point nuts for any loose or missing nuts 
and replacement, as specified in a European Union Aviation Safety 
Agency (EASA) AD, which is incorporated by reference. The FAA is 
issuing this AD to address the unsafe condition on these products.

DATES: This AD becomes effective September 9, 2020.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of September 9, 
2020.
    The FAA must receive comments on this AD by October 9, 2020.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For material incorporated by reference (IBR) in this AD, contact 
the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 
221 8999 000; email [email protected]; internet www.easa.europa.eu. 
You may find this IBR material on the EASA website at https://ad.easa.europa.eu. You may view this IBR material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195. It is also available in the AD 
docket on the internet at https://www.regulations.gov by searching for 
and locating Docket No. FAA-2020-0777.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
0777; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this AD, any comments received, and other information. The street 
address for Docket Operations is listed above. Comments will be 
available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
Large Aircraft Section, International Validation Branch, FAA, 2200 
South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3226; 
email [email protected].

SUPPLEMENTARY INFORMATION:

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2020-0168R1, dated July 29, 2020 
(``EASA AD 2020-0168R1'') (also referred to as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for certain Dassault Aviation Model MYSTERE-FALCON 900, 
FALCON 900EX, FALCON 2000, and FALCON 2000EX airplanes.
    This AD was prompted by reports of loose or missing nuts on the 
pilot and co-pilot ventral seat belt attachment points. The FAA is 
issuing this AD to address this condition, which could lead to 
detachment of the seat belt at a critical phase of flight, such as 
landing or, in the case of turbulence or emergency landing, resulting 
in the flight crew becoming unrestrained from their seat, causing 
injury to the flight crew and/or subsequent loss of control of the 
airplane. This condition could impede the continued safety of flight. 
See the MCAI for additional background information.

[[Page 52255]]

Related IBR Material Under 1 CFR Part 51

    EASA AD 2020-0168R1 describes procedures for a detailed inspection 
of certain seat belt attaching point nuts for any loose or missing nuts 
and corrective action, which is replacement. This material is 
reasonably available because the interested parties have access to it 
through their normal course of business or by the means identified in 
the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is issuing this AD because the FAA evaluated 
all pertinent information and determined the unsafe condition exists 
and is likely to exist or develop on other products of the same type 
design.

Requirements of This AD

    This AD requires accomplishing the actions specified in EASA AD 
2020-0168R1, described previously, as incorporated by reference, except 
for any differences identified as exceptions in the regulatory text of 
this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding FAA ADs. The FAA has 
since coordinated with other manufacturers and civil aviation 
authorities (CAAs) to use this process. As a result, EASA AD 2020-
0168R1 is incorporated by reference in this final rule. This AD, 
therefore, requires compliance with EASA AD 2020-0168R1 in its 
entirety, through that incorporation, except for any differences 
identified as exceptions in the regulatory text of this AD. Using 
common terms that are the same as the heading of a particular section 
in the EASA AD does not mean that operators need comply only with that 
section. For example, where the AD requirement refers to ``all required 
actions and compliance times,'' compliance with this AD requirement is 
not limited to the section titled ``Required Action(s) and Compliance 
Time(s)'' in the EASA AD. Service information specified in EASA AD 
2020-0168R1 that is required for compliance with EASA AD 2020-0168R1 is 
available on the internet at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2020-0777.

FAA's Justification and Determination of the Effective Date

    An unsafe condition exists that requires the immediate adoption of 
this AD without providing an opportunity for public comments prior to 
adoption. The FAA has found that the risk to the flying public 
justifies foregoing notice and comment prior to adoption of this rule 
because the detachment of the seat belt at a critical phase of flight 
such as landing or, in the case of turbulence or emergency landing, 
could result in the flight crew becoming unrestrained from their seat, 
causing injury to the flight crew and/or subsequent loss of control of 
the airplane, thereby impeding continued safety of flight. In addition, 
the compliance time for the required action is shorter than the time 
necessary for the public to comment and for publication of the final 
rule. Therefore, the FAA finds good cause that notice and opportunity 
for prior public comment are impracticable. In addition, for the 
reasons stated above, the FAA finds that good cause exists for making 
this amendment effective in less than 30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety, and the FAA did not precede it by notice and opportunity for 
public comment. The FAA invites you to send any written relevant data, 
views, or arguments about this AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2020-0777; 
Project Identifier MCAI-2020-01071-T'' at the beginning of your 
comments. The most helpful comments reference a specific portion of the 
proposal, explain the reason for any recommended change, and include 
supporting data. To ensure the docket does not contain duplicate 
comments, commenters should submit only one copy of the comments.
    Except for Confidential Business Information (CBI) as described in 
the following paragraph, and other information as described in 14 CFR 
11.35, the FAA will post all comments the FAA receives, without change, 
to https://www.regulations.gov, including any personal information you 
provide. The FAA will also post a report summarizing each substantive 
verbal contact the FAA receives about this AD.

Confidential Business Information

    CBI is commercial or financial information that is both customarily 
and actually treated as private by its owner. Under the Freedom of 
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public 
disclosure. If your comments responsive to this AD contain commercial 
or financial information that is customarily treated as private, that 
you actually treat as private, and that is relevant or responsive to 
this AD, it is important that you clearly designate the submitted 
documents as CBI. Please mark each page of your submission containing 
CBI as ``PROPIN.'' The FAA will treat such marked submissions as 
confidential under the FOIA, and they will not be placed in the public 
docket of this AD. Submissions containing CBI should be sent to the 
person identified in the FOR FURTHER INFORMATION CONTACT section. Any 
commentary that the FAA receives that is not specifically designated as 
CBI will be placed in the public docket for this rulemaking.

Regulatory Flexibility Act (RFA)

    The requirements of the RFA do not apply when an agency finds good 
cause pursuant to 5 U.S.C. 553 to adopt a rule without prior notice and 
comment. Because the FAA has determined that it has good cause to adopt 
this rule without notice and comment, RFA analysis is not required.

Costs of Compliance

    The FAA estimates that this AD affects 793 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
4 work-hours x $85 per hour = $340...........................              $4             $344         $272,792
----------------------------------------------------------------------------------------------------------------


[[Page 52256]]

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866, and
    (2) Will not affect intrastate aviation in Alaska.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2020-17-12 Dassault Aviation: Amendment 39-21217; Docket No. FAA-
2020-0777; Project Identifier MCAI-2020-01071-T.

(a) Effective Date

    This AD becomes effective September 9, 2020.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Dassault Aviation Model MYSTERE-FALCON 900, 
FALCON 900EX, FALCON 2000, and FALCON 2000EX airplanes, certificated 
in any category, as identified in European Union Aviation Safety 
Agency (EASA) AD 2020-0168R1, dated July 29, 2020 (``EASA AD 2020-
0168R1'').

(d) Subject

    Air Transport Association (ATA) of America Code 25, Equipment/
furnishings.

(e) Reason

    This AD was prompted by reports of loose or missing nuts on the 
pilot and co-pilot ventral seat belt attachment points. The FAA is 
issuing this AD to address this condition, which could lead to 
detachment of the seat belt at a critical phase of flight such as 
landing or, in the case of turbulence or emergency landing, 
resulting in the flight crew becoming unrestrained from their seat, 
causing injury to the flight crew and/or subsequent loss of control 
of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2020-0168R1.

(h) Exceptions to EASA AD EASA AD 2020-0168R1

    (1) Where EASA AD 2020-0168R1 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) Where paragraph (2) of EASA AD 2020-0168R1 specifies actions 
if, ``deficiencies (as defined in the applicable inspection SB) are 
found on,'' for this AD deficiencies are defined as any missing nuts 
or any axial end play on any bolt assemblies (loose nuts).
    (3) Paragraph (4) of EASA AD 2020-0168R1 provides credit for 
``accomplishment of a `C' check (as per Dassault definition).'' For 
this AD, that credit is allowed provided it can be conclusively 
determined that each affected part was inspected as specified in 
that `C' check.
    (4) The ``Remarks'' section of EASA AD 2020-0168R1 does not 
apply to this AD.

(i) No Reporting Requirement

    Although the service information referenced in EASA AD 2020-
0168R1 specifies to submit certain information to the manufacturer, 
this AD does not include that requirement.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the Large Aircraft Section, International Validation 
Branch, send it to the attention of the person identified in 
paragraph (k) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office/
certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Dassault 
Aviation's EASA Design Organization Approval (DOA). If approved by 
the DOA, the approval must include the DOA-authorized signature.

(k) Related Information

    For more information about this AD, contact Tom Rodriguez, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3226; email [email protected].

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Union Aviation Safety Agency (EASA) AD 2020-0168R1, 
dated July 29, 2020.
    (ii) [Reserved]
    (3) For information about EASA AD 2020-0168R1, contact the EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
8999 000; email [email protected]; internet www.easa.europa.eu. You 
may find this EASA AD on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this material at the FAA, Airworthiness 
Products Section, Operational Safety Branch, 2200 South 216th St., 
Des Moines, WA. For information on the availability of this material 
at the FAA, call 206-231-3195. This material may be found in the AD 
docket on the internet at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2020-0777.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, email 
[email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.


[[Page 52257]]


    Issued on August 13, 2020.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2020-18488 Filed 8-24-20; 8:45 am]
BILLING CODE 4910-13-P