[Federal Register Volume 85, Number 127 (Wednesday, July 1, 2020)]
[Rules and Regulations]
[Pages 39470-39471]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-13982]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0990; Product Identifier 2019-NM-122-AD; Amendment 
39-21156; AD 2020-14-02]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; correction.

-----------------------------------------------------------------------

SUMMARY: The FAA is correcting an airworthiness directive (AD) that 
published in the Federal Register. That AD applies to all The Boeing 
Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-
200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series 
airplanes. As published, the AD number and Amendment number specified 
in the preamble and regulatory text are incorrect. This document 
corrects that error. In all other respects, the original document 
remains the same.

DATES: This correction is effective July 28, 2020.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of July 28, 
2020 (85 FR 37547, June 23, 2020).

ADDRESSES: For service information identified in this final rule, 
contact Boeing Commercial Airplanes, Attention: Contractual & Data 
Services (C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 
90740-5600; phone: 562-797-1717; internet: https://www.myboeingfleet.com. You may view this referenced service information 
at the FAA, Airworthiness Products Section, Operational Safety Branch, 
2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195. It is also 
available on the internet at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2019-0990.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov; or in person at the Docket Management Facility 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this AD, any comments received, and 
other information. The address for Docket Operations is Docket 
Management Facility, U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Eric Lin, Aerospace Engineer, Airframe 
Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 
98198; phone and fax: 206-231-3523; email: [email protected].

SUPPLEMENTARY INFORMATION: This AD requires repetitive detailed 
inspections and open hole high frequency eddy current (HFEC) 
inspections of the upper splice fittings for cracks and applicable on-
condition actions for all The Boeing Company Model 747-100, 747-100B, 
747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 
747-400F, 747SR, and 747SP series airplanes.

Need for the Correction

    As published on June 23, 2020 (85 FR 37547), the AD and Amendment 
numbers for this AD specified in the preamble and regulatory text are 
incorrect. The incorrectly specified AD number was AD 2020-12-10 and 
the incorrectly specified Amendment number was 39-19919; AD number AD 
2020-12-10 is assigned to another AD addressing a Bell Textron Inc. 
helicopter unsafe condition, Amendment 39-21145 (85 FR 35555, June 11, 
2020). The correct AD number for this AD is AD 2020-14-02 and the 
correct Amendment number is 39-21156.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Boeing Alert Requirements Bulletin 747-53A2899 RB, 
Revision 1, dated April 7, 2020. This service information describes 
procedures for repetitive detailed inspections and open hole HFEC 
inspections of the left and right upper splice fittings for cracks and 
applicable on-condition actions. On-condition actions include repair. 
This service information is reasonably available because the interested 
parties have

[[Page 39471]]

access to it through their normal course of business or by the means 
identified in the ADDRESSES section.

Correction of Publication

    This document corrects an error and correctly adds the AD as an 
amendment to 14 CFR 39.13. Although no other part of the preamble or 
regulatory information has been corrected, the FAA is publishing the 
entire rule in the Federal Register.
    The effective date of this AD remains July 28, 2020.
    Since this action only corrects the AD number and amendment number, 
it has no adverse economic impact and imposes no additional burden on 
any person. Therefore, the FAA has determined that notice and public 
comment procedures are unnecessary.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Correction

    Accordingly, pursuant to the authority delegated to me by the 
Administrator, the Federal Aviation Administration amends part 39 of 
the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Corrected]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2020-14-02 The Boeing Company: Amendment 39-21156; Docket No. FAA-
2019-0990; Product Identifier 2019-NM-122-AD.

(a) Effective Date

    This AD is effective July 28, 2020.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all The Boeing Company Model 747-100, 747-
100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 
747-400D, 747-400F, 747SR, and 747SP series airplanes, certificated 
in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

(e) Unsafe Condition

    This AD was prompted by reports of cracking in particular areas 
of the bulkhead structure at body station (BS) 2598. The FAA is 
issuing this AD to address fatigue cracking of the BS 2598 bulkhead 
structure, which could adversely affect the structural integrity of 
the bulkhead and the horizontal stabilizer support structure, and 
result in loss of controllability of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Except as specified by paragraph (h) of this AD: At the 
applicable times specified in the ``Compliance'' paragraph of Boeing 
Alert Requirements Bulletin 747-53A2899 RB, Revision 1, dated April 
7, 2020, do all applicable actions identified in, and in accordance 
with, the Accomplishment Instructions of Boeing Alert Requirements 
Bulletin 747-53A2899 RB, Revision 1, dated April 7, 2020.

    Note 1 to paragraph (g): Guidance for accomplishing the actions 
required by this AD can be found in Boeing Alert Service Bulletin 
747-53A2899, Revision 1, dated April 7, 2020, which is referred to 
in Boeing Alert Requirements Bulletin 747-53A2899 RB, Revision 1, 
dated April 7, 2020.

(h) Exceptions to Service Information Specifications

    (1) For purposes of determining compliance with the requirements 
of this AD: Where Boeing Alert Requirements Bulletin 747-53A2899 RB, 
Revision 1, dated April 7, 2020, uses the phrase ``the original 
issue date of Requirements Bulletin 747-53A2899 RB,'' this AD 
requires using ``the effective date of this AD.''
    (2) Where Boeing Alert Requirements Bulletin 747-53A2899 RB, 
Revision 1, dated April 7, 2020, specifies contacting Boeing for 
repair instructions: This AD requires doing the repair using a 
method approved in accordance with the procedures specified in 
paragraph (j) of this AD.

(i) Credit for Previous Actions

    This paragraph provides credit for the actions specified in 
paragraph (g) of this AD, if those actions were performed before the 
effective date of this AD using Boeing Alert Requirements Bulletin 
747-53A2899 RB, dated April 5, 2019.

(j) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO Branch, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request 
to your principal inspector or local Flight Standards District 
Office, as appropriate. If sending information directly to the 
manager of the certification office, send it to the attention of the 
person identified in paragraph (k)(1) of this AD. Information may be 
emailed to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by The Boeing Company Organization Designation 
Authorization (ODA) that has been authorized by the Manager, Seattle 
ACO Branch, FAA, to make those findings. To be approved, the repair 
method, modification deviation, or alteration deviation must meet 
the certification basis of the airplane, and the approval must 
specifically refer to this AD.

(k) Related Information

    (1) For more information about this AD, contact Eric Lin, 
Aerospace Engineer, Airframe Section, FAA, Seattle ACO Branch, 2200 
South 216th St., Des Moines, WA 98198; phone and fax: 206-231-3523; 
email: [email protected].
    (2) Service information identified in this AD that is not 
incorporated by reference is available at the addresses specified in 
paragraphs (l)(4) and (5) of this AD.

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (3) The following service information was approved for IBR on 
July 28, 2020 (85 FR 37547, June 23, 2020).
    (i) Boeing Alert Requirements Bulletin 747-53A2899 RB, Revision 
1, dated April 7, 2020.
    (ii) [Reserved]
    (4) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; phone: 562-797-1717; internet: https://www.myboeingfleet.com.
    (5) You may view this service information at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195.
    (6) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, email [email protected], or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued on June 24, 2020.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2020-13982 Filed 6-30-20; 8:45 am]
BILLING CODE 4910-13-P