[Federal Register Volume 85, Number 85 (Friday, May 1, 2020)]
[Proposed Rules]
[Pages 25356-25359]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-09139]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-0347; Product Identifier 2020-NM-042-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus SAS Model A300 F4-600R series airplanes. This 
proposed AD was prompted by a report of damaged main deck cargo 
crossbeams on the right-hand side, between certain frame locations. 
This proposed AD would require repetitive detailed inspections of the 
affected main deck cargo crossbeams for any damage, and depending on 
findings, accomplishment of applicable corrective actions, as specified 
in a European Union Aviation Safety Agency (EASA) AD, which will be 
incorporated by reference. This proposed AD would also provide optional 
terminating actions for the repetitive detailed inspections. The FAA is 
proposing this AD to address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by June 15, 
2020.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For the material identified in this proposed AD that will be 
incorporated by reference (IBR), contact the EASA, Konrad-Adenauer-Ufer 
3, 50668 Cologne, Germany; phone: +49 221 89990 1000; email: 
[email protected]; internet: www.easa.europa.eu. You may find this IBR 
material on the EASA website at https://ad.easa.europa.eu. You may view 
this IBR material at the FAA, Airworthiness Products Section, 
Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 206-
231-3195. It is also available in the AD docket on the internet at 
https://www.regulations.gov by searching for and locating Docket No. 
FAA-2020-0347.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
0347; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations is listed above. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, Large 
Aircraft Section, International Validation Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; phone and fax: 206-231-3225; email: 
[email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2020-0347; 
Product Identifier 2020-NM-042-AD'' at the beginning of your comments. 
The FAA specifically invites comments on the overall regulatory, 
economic, environmental, and energy aspects of this NPRM. The FAA will 
consider all comments received by the closing date and may amend this 
NPRM based on those comments.
    The FAA will post all comments, without change, to https://www.regulations.gov, including any personal information you provide. 
The FAA will also post a report summarizing each substantive verbal 
contact received about this NPRM.

[[Page 25357]]

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2020-0050, dated March 9, 2020; 
corrected March 11, 2020 (``EASA AD 2020-0050'') (also referred to as 
the Mandatory Continuing Airworthiness Information, or ``the MCAI''), 
to correct an unsafe condition for certain Airbus SAS Model A300 F4-
600R series airplanes.
    This proposed AD was prompted by a report of damaged main deck 
cargo crossbeams on the right-hand side, between certain frame 
locations. The FAA is proposing this AD to address damaged main deck 
cargo crossbeams, which could adversely affect the structural integrity 
of the airplane. See the MCAI for additional background information.

Related IBR Material Under 1 CFR Part 51

    EASA AD 2020-0050 describes procedures for repetitive detailed 
inspections of the affected main deck cargo crossbeams from frame (FR) 
48 to FR54 for any damage (including bent, curved, and cracked 
crossbeams); corrective actions; and terminating actions. Corrective 
actions include detailed inspections of the right-hand and left-hand 
crossbeams and lugs for damage (including buckling and cracking) and 
correct diameter of the lug/crossbeam holes; repair; and replacement of 
damaged crossbeams. Optional terminating actions include replacement of 
crossbeams with reinforced machined crossbeams.
    This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is proposing this AD because the FAA 
evaluated all the relevant information and determined the unsafe 
condition described previously is likely to exist or develop in other 
products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2020-0050 described previously, as incorporated by 
reference, except for any differences identified as exceptions in the 
regulatory text of this AD. This proposed AD also would require sending 
the inspection results to Airbus SAS.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding FAA ADs. The FAA has 
since coordinated with other manufacturers and civil aviation 
authorities (CAAs) to use this process. As a result, EASA AD 2020-0050 
will be incorporated by reference in the FAA final rule. This proposed 
AD would, therefore, require compliance with EASA AD 2020-0050 in its 
entirety, through that incorporation, except for any differences 
identified as exceptions in the regulatory text of this proposed AD. 
Using common terms that are the same as the heading of a particular 
section in the EASA AD does not mean that operators need comply only 
with that section. For example, where the AD requirement refers to 
``all required actions and compliance times,'' compliance with this AD 
requirement is not limited to the section titled ``Required Action(s) 
and Compliance Time(s)'' in the EASA AD. Service information specified 
in EASA AD 2020-0050 that is required for compliance with EASA AD 2020-
0050 will be available on the internet at https://www.regulations.gov 
by searching for and locating Docket No. FAA-2020-0347 after the FAA 
final rule is published.

Costs of Compliance

    The FAA estimates that this proposed AD affects 52 airplanes of 
U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
                           Labor cost                               Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
6 work-hours x $85 per hour = $510..............................              $0            $510         $26,520
----------------------------------------------------------------------------------------------------------------

    The FAA estimates that it would take about 1 work-hour per product 
to comply with the proposed reporting requirement in this proposed AD. 
The average labor rate is $85 per hour. Based on these figures, the FAA 
estimates the cost of reporting the inspection results on U.S. 
operators to be $4,420, or $85 per product.
    The FAA estimates the following costs to do any necessary on-
condition repairs that would be required based on the results of any 
required actions. The FAA has no way of determining the number of 
aircraft that might need these on-condition actions:

                 Estimated Costs of On-Condition Repairs
------------------------------------------------------------------------
                                                             Cost per
               Labor cost                   Parts cost        product
------------------------------------------------------------------------
6 work-hours x $85 per hour = $510......         $10,000         $10,510
------------------------------------------------------------------------

    The FAA has received no definitive data that would enable the FAA 
to provide cost estimates for the on-condition inspections and 
replacements specified in this proposed AD.
    The FAA estimates the following costs to do the optional 
terminating actions specified in this proposed AD.

[[Page 25358]]



            Estimated Costs for Optional Terminating Actions
------------------------------------------------------------------------
                                                             Cost per
               Labor cost                   Parts cost        product
------------------------------------------------------------------------
18 work-hours x $85 per hour = $1,530...         $10,000         $11,530
------------------------------------------------------------------------

Paperwork Reduction Act

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to penalty for 
failure to comply with a collection of information subject to the 
requirements of the Paperwork Reduction Act unless that collection of 
information displays a current valid OMB control number. The control 
number for the collection of information required by this proposed AD 
is 2120-0056. The paperwork cost associated with this proposed AD has 
been detailed in the Costs of Compliance section of this document and 
includes time for reviewing instructions, as well as completing and 
reviewing the collection of information. Therefore, all reporting 
associated with this proposed AD is mandatory. Comments concerning the 
accuracy of this burden and suggestions for reducing the burden should 
be directed to Information Collection Clearance Officer, Federal 
Aviation Administration, 10101 Hillwood Parkway, Fort Worth, TX 76177-
1524.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Airbus SAS: Docket No. FAA-2020-0347; Product Identifier 2020-NM-
042-AD.

(a) Comments Due Date

    The FAA must receive comments by June 15, 2020.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS Model A300 F4-605R and F4-622R 
airplanes, certificated in any category, as identified in European 
Union Aviation Safety Agency (EASA) AD 2020-0050, dated March 9, 
2020; corrected March 11, 2020 (``EASA AD 2020-0050'').

(d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

(e) Reason

    This AD was prompted by a report of damaged main deck cargo 
crossbeams on the right-hand side, between certain frame locations. 
The FAA is issuing this AD to address damaged main deck cargo 
crossbeams, which could adversely affect the structural integrity of 
the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2020-0050.

(h) Exceptions to EASA AD 2020-0050

    (1) Where EASA AD 2020-0050 refers to its effective date, this 
AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2020-0050 does not apply 
to this AD.
    (3) Paragraph (4) of EASA AD 2020-0050 specifies to report 
inspection results to Airbus within a certain compliance time. For 
this AD, report inspection results at the applicable time specified 
in paragraph (h)(3)(i) or (ii) of this AD.
    (i) If the inspection was done on or after the effective date of 
this AD: Submit the report within 30 days after the inspection.
    (ii) If the inspection was done before the effective date of 
this AD: Submit the report within 30 days after the effective date 
of this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Large Aircraft Section, International Validation Branch, FAA, has 
the authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (j)(2) of this AD. Information 
may be emailed to: [email protected]. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, Large Aircraft 
Section, International Validation Branch, FAA; or EASA; or Airbus 
SAS's EASA Design Organization Approval (DOA). If approved by

[[Page 25359]]

the DOA, the approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): For any service information 
referenced in EASA AD 2020-0050 that contains RC procedures and 
tests: Except as required by paragraph (i)(2) of this AD, RC 
procedures and tests must be done to comply with this AD; any 
procedures or tests that are not identified as RC are recommended. 
Those procedures and tests that are not identified as RC may be 
deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the procedures and tests identified as 
RC can be done and the airplane can be put back in an airworthy 
condition. Any substitutions or changes to procedures or tests 
identified as RC require approval of an AMOC.
    (4) Paperwork Reduction Act Burden Statement: A federal agency 
may not conduct or sponsor, and a person is not required to respond 
to, nor shall a person be subject to a penalty for failure to comply 
with a collection of information subject to the requirements of the 
Paperwork Reduction Act unless that collection of information 
displays a current valid OMB Control Number. The OMB Control Number 
for this information collection is 2120-0056. Public reporting for 
this collection of information is estimated to be approximately 1 
hour per response, including the time for reviewing instructions, 
searching existing data sources, gathering and maintaining the data 
needed, and completing and reviewing the collection of information. 
All responses to this collection of information are mandatory as 
required by this AD; the nature and extent of confidentiality to be 
provided, if any. Send comments regarding this burden estimate or 
any other aspect of this collection of information, including 
suggestions for reducing this burden to Information Collection 
Clearance Officer, Federal Aviation Administration, 10101 Hillwood 
Parkway, Fort Worth, TX 76177-1524.

(j) Related Information

    (1) For information about EASA AD 2020-0050, contact the EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; phone: +49 221 89990 
6017; email: [email protected]; internet: www.easa.europa.eu. You 
may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this material at the FAA, 
Airworthiness Products Section, Operational Safety Branch, 2200 
South 216th St., Des Moines, WA. For information on the availability 
of this material at the FAA, call 206-231-3195. This material may be 
found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-
2020-0347.
    (2) For more information about this AD, contact Dan Rodina, 
Aerospace Engineer, Large Aircraft Section, International Validation 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; phone and 
fax: 206-231-3225; email: [email protected].

    Issued on April 23, 2020.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness 
Division, Aircraft Certification Service.
[FR Doc. 2020-09139 Filed 4-30-20; 8:45 am]
 BILLING CODE 4910-13-P