[Federal Register Volume 85, Number 70 (Friday, April 10, 2020)]
[Proposed Rules]
[Pages 20209-20211]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-07464]



[[Page 20209]]

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2020-0329; Product Identifier 2020-NM-028-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus SAS Model A320-214, -216, -231, -232, -233, -251N, 
and -271N airplanes. This proposed AD was prompted by a report that 
following the installation of a second cargo fire extinguishing bottle, 
insufficient clearance between the cargo compartment fire extinguishing 
pipes was found. This proposed AD would require inspection and 
modification of the cargo compartment fire extinguishing pipes, and on-
condition actions if necessary, as specified in a European Union 
Aviation Safety Agency (EASA) AD, which will be incorporated by 
reference. The FAA is proposing this AD to address the unsafe condition 
on these products.

DATES: The FAA must receive comments on this proposed AD by May 26, 
2020.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For the material identified in this proposed AD that will be 
incorporated by reference (IBR), contact the EASA, Konrad-Adenauer-Ufer 
3, 50668 Cologne, Germany; telephone +49 221 89990 1000; email 
[email protected]; internet www.easa.europa.eu. You may find this IBR 
material on the EASA website at https://ad.easa.europa.eu. You may view 
this IBR material at the FAA, Transport Standards Branch, 2200 South 
216th St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195. It is also available in the AD 
docket on the internet at https://www.regulations.gov by searching for 
and locating Docket No. FAA-2020-0329.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
0329; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations is listed above. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Sanjay Ralhan, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3223; email 
[email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2020-0329; 
Product Identifier 2020-NM-028-AD'' at the beginning of your comments. 
The FAA specifically invites comments on the overall regulatory, 
economic, environmental, and energy aspects of this NPRM. The FAA will 
consider all comments received by the closing date and may amend this 
NPRM based on those comments.
    The FAA will post all comments, without change, to https://www.regulations.gov, including any personal information you provide. 
The FAA will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Discussion

    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2019-0279R1, dated February 5, 2020 
(``2019-0279R1'') (also referred to as the Mandatory Continuing 
Airworthiness Information, or ``the MCAI''), to correct an unsafe 
condition for certain Airbus SAS Model A320-214, -216, -231, -232, -
233, -251N, and -271N airplanes.
    This proposed AD was prompted by a report that following the 
installation of a second cargo fire extinguishing bottle, insufficient 
clearance between the cargo compartment fire extinguishing pipes was 
found. The FAA is proposing this AD to address insufficient clearance 
between the cargo compartment fire extinguishing pipes, which could 
lead to wear and chafing of the pipes and possibly result in reduced 
fire extinguishing capability in case of a cargo compartment fire. See 
the MCAI for additional background information.

Related IBR Material Under 1 CFR Part 51

    EASA AD 2019-0279R1 describes procedures for an inspection and 
modification of the cargo compartment fire extinguishing pipes, 
including installing a clamp, checking the distance between the pipes, 
and accomplishing on-condition actions including adjusting the screws 
and pipes and installing a spacer between the two pipes. This material 
is reasonably available because the interested parties have access to 
it through their normal course of business or by the means identified 
in the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to the FAA's bilateral agreement with the State of Design Authority, 
the FAA has been notified of the unsafe condition described in the MCAI 
referenced above. The FAA is proposing this AD because the FAA 
evaluated all the relevant information and determined the unsafe 
condition described previously is likely to exist or develop in other 
products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in EASA AD 2019-0279R1 described previously, as incorporated by 
reference, except for any differences identified as exceptions in the 
regulatory text of this AD.

Explanation of Required Compliance Information

    In the FAA's ongoing efforts to improve the efficiency of the AD 
process, the FAA initially worked with Airbus and EASA to develop a 
process to use certain EASA ADs as the primary source of information 
for compliance with requirements for corresponding

[[Page 20210]]

FAA ADs. The FAA has since coordinated with other manufacturers and 
civil aviation authorities (CAAs) to use this process. As a result, 
EASA AD 2019-0279R1 will be incorporated by reference in the FAA final 
rule. This proposed AD would, therefore, require compliance with EASA 
AD 2019-0279R1 in its entirety, through that incorporation, except for 
any differences identified as exceptions in the regulatory text of this 
proposed AD. Using common terms that are the same as the heading of a 
particular section in the EASA AD does not mean that operators need 
comply only with that section. For example, where the AD requirement 
refers to ``all required actions and compliance times,'' compliance 
with this AD requirement is not limited to the section titled 
``Required Action(s) and Compliance Time(s)'' in the EASA AD. Service 
information specified in EASA AD 2019-0279R1 that is required for 
compliance with EASA AD 2019-0279R1 will be available on the internet 
at https://www.regulations.gov by searching for and locating Docket No. 
FAA-2020-0329 after the FAA final rule is published.

Costs of Compliance

    The FAA estimates that this proposed AD affects 368 airplanes of 
U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                              Cost per
                Labor cost                   Parts cost        product            Cost on  U.S. operators
----------------------------------------------------------------------------------------------------------------
Up to 3 work-hours x $85 per hour = $255.            $103      Up to $358  Up to $131,744.
----------------------------------------------------------------------------------------------------------------

    The FAA has received no definitive data that would enable the 
agency to provide cost estimates for the on-condition actions specified 
in this proposed AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    The FAA determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Airbus SAS: Docket No. FAA-2020-0329; Product Identifier 2020-NM-
028-AD.

(a) Comments Due Date

    The FAA must receive comments by May 26, 2020.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus SAS Model A320-214, -216, -231, -232, 
-233, -251N, and -271N airplanes, certificated in any category, as 
identified in European Union Aviation Safety Agency (EASA) AD 2019-
0279R1, dated February 5, 2020 (``EASA AD 2019-0279R1'').

(d) Subject

    Air Transport Association (ATA) of America Code 26, Fire 
protection.

(e) Reason

    This AD was prompted by a report that following the installation 
of a second cargo fire extinguishing bottle, insufficient clearance 
between the cargo compartment fire extinguishing pipes was found. 
The FAA is issuing this AD to address insufficient clearance between 
the cargo compartment fire extinguishing pipes, which could lead to 
wear and chafing of the pipes and possibly result in reduced fire 
extinguishing capability in case of a cargo compartment fire.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, EASA AD 2019-0279R1.

(h) Exceptions to EASA AD 2019-0279R1

    (1) Where EASA AD 2019-0279R1 refers to ``the effective date of 
the original issue of [AD 2019-0279]'' or ``the effective date of 
this revised AD,'' this AD requires using the effective date of this 
AD.
    (2) The ``Remarks'' section of EASA AD 2019-0279R1 does not 
apply to this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (j)(2) of this AD. Information 
may

[[Page 20211]]

be emailed to: [email protected]. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved by the Manager, International 
Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS's 
EASA Design Organization Approval (DOA). If approved by the DOA, the 
approval must include the DOA-authorized signature.
    (3) Required for Compliance (RC): For any service information 
referenced in EASA AD 2019-0279R1 that contains RC procedures and 
tests: Except as required by paragraph (i)(2) of this AD, RC 
procedures and tests must be done to comply with this AD; any 
procedures or tests that are not identified as RC are recommended. 
Those procedures and tests that are not identified as RC may be 
deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the procedures and tests identified as 
RC can be done and the airplane can be put back in an airworthy 
condition. Any substitutions or changes to procedures or tests 
identified as RC require approval of an AMOC.

(j) Related Information

    (1) For information about EASA AD 2019-0279R1, contact the EASA, 
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 
89990 6017; email [email protected]; Internet www.easa.europa.eu. 
You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this material at the FAA, Transport 
Standards Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 
206-231-3195. This material may be found in the AD docket on the 
internet at https://www.regulations.gov by searching for and 
locating Docket No. FAA-2020-0329.
    (2) For more information about this AD, contact Sanjay Ralhan, 
Aerospace Engineer, International Section, Transport Standards 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3223; email [email protected].

    Issued on April 3, 2020.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2020-07464 Filed 4-9-20; 8:45 am]
 BILLING CODE 4910-13-P