[Federal Register Volume 85, Number 28 (Tuesday, February 11, 2020)]
[Rules and Regulations]
[Pages 7653-7655]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-02587]



 ========================================================================
 Rules and Regulations
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains regulatory documents 
 having general applicability and legal effect, most of which are keyed 
 to and codified in the Code of Federal Regulations, which is published 
 under 50 titles pursuant to 44 U.S.C. 1510.
 
 The Code of Federal Regulations is sold by the Superintendent of Documents. 
 
 ========================================================================
 

  Federal Register / Vol. 85, No. 28 / Tuesday, February 11, 2020 / 
Rules and Regulations  

[[Page 7653]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2017-0052; Product Identifier 2016-SW-081-AD; Amendment 
39-21024; AD 2020-02-11]
RIN 2120-AA64


Airworthiness Directives; Bell Helicopter Textron Inc. 
Helicopters

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is superseding Airworthiness Directive (AD) 2015-04-04 
for Bell Helicopter Textron Inc. (Bell) Model 412 and 412EP 
helicopters. AD 2015-04-04 required revising the Rotorcraft Flight 
Manual (RFM) for your helicopter and installing a placard to limit 
flights to visual flight rules (VFR) and prohibit night operations 
because of failing inverters. This AD requires replacing the affected 
inverter with a new inverter. This AD was prompted by numerous failures 
of inverters. The FAA is issuing this AD to address the unsafe 
condition on these products.

DATES: This AD is effective March 17, 2020.

ADDRESSES: For service information identified in this final rule, 
contact Bell Helicopter Textron, Inc., P.O. Box 482, Fort Worth, TX 
76101; telephone 817-280-3391; fax 817-280-6466; or at https://www.bellcustomer.com. You may view this service information at the FAA, 
Office of the Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., 
Room 6N-321, Fort Worth, TX 76177.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.govby searching for and locating Docket No. FAA-2017-
0052; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this AD, the economic evaluation, any comments received, and other 
information. The address for Docket Operations is Docket Operations, 
U.S. Department of Transportation, Docket Operations, M-30, West 
Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, 
Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Tim Beauregard, Aviation Safety 
Engineer, DSCO Branch, AIR-7J0, FAA, 10101 Hillwood Pkwy., Fort Worth, 
TX 76177; telephone 817-222-5190; email [email protected].

SUPPLEMENTARY INFORMATION:

Discussion

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 to supersede AD 2015-04-04, Amendment 39-18106 (80 FR 9594, 
February 24, 2015) (``AD 2015-04-04''). AD 2015-04-04 applied to Bell 
Model 412 and 412EP helicopters with a static inverter part number (P/
N) 412-375-079-101 or 412-375-079-103 with a serial number 29145 or 
higher installed. The NPRM published in the Federal Register on August 
2, 2018 (83 FR 37764). The NPRM was prompted by numerous failures of 
inverters and a newly introduced improved inverter, which corrects the 
unsafe condition. Bell determined the root causes of the failures were 
an external connector that caused a short circuit inside inverter P/N 
412-375-079-101 and components chafing because of variations in the 
assembly process and packaging tolerances for inverter P/N 412-375-079-
103. Bell introduced an improved inverter, P/N 412-375-079-105, and 
retrofit kits to replace inverter P/N 412-375-079-101 or 412-375-079-
103 on helicopters with serial numbers 33001 or higher. These 
replacements and repairs correct the unsafe condition by providing 450 
voltage amperes (VA) of total power instead of 500 VA, thereby reducing 
the input power to the inverter. The NPRM proposed to require these 
repairs and replacements. The FAA is issuing this AD to address the 
unsafe condition on these products.

Comments

    After the NPRM was published, The FAA received comments from two 
commenters, Bell and Leonardo Helicopters. The following presents the 
comments received on the NPRM, and the FAA's response to each comment.
    Request: Bell and Leonardo Helicopters requested clarification as 
to why the FAA did not indicate that the NPRM applied to helicopters 
with static inverters that had a serial number 29145 or higher in the 
NPRM's Applicability section. Leonardo Helicopters stated no evidence 
exists that static inverters with a serial number lower than 29145 have 
the unsafe condition described in the NPRM.
    FAA Response: The FAA agrees and has revised this AD to specify 
that this AD only applies to static inverters with serial numbers 29145 
or higher.
    Request: Bell requested the FAA allow inverter P/N 412-375-079-103 
450 VA or P/N 412-375-079-101 450 VA to be replaced by inverter P/N 
412-075-158-101 250 VA if the Electrical Load Analysis (ELA) 
requirements are met per Bell Alert Service Bulletin 412-16-171, dated 
March 22, 2016 (ASB 412-16-171).
    FAA Response: The FAA disagrees. ASB 412-16-171 does not have a 
standard listed for how to conduct the ELA or the margins that may be 
acceptable. Therefore, the FAA could not legally enforce such a 
requirement.
    Request: Bell requested the FAA either increase the 25 hours time-
in-service (TIS) compliance time or add an alternate compliance date 
because no additional failures have occurred since ASB 412-16-171 was 
issued.
    FAA Response: The FAA disagrees. ASB 412-16-171 set a compliance 
time no later than January 1, 2017. The FAA believes that 25 hours TIS 
is appropriate given that three years have passed between the deadline 
in ASB 412-16-171 and the publication of this final rule.
    Request: Bell requested that the FAA correct an error in the NPRM. 
The NPRM stated that Bell introduced a new inverter and recommended 
repairs that ``correct the unsafe condition by providing 250 VA of 
total power instead of 500 VA, thereby reducing the input power to the 
inverter.'' Bell stated that ``250 VA'' should be changed to ``450 
VA.''
    FAA Response: The FAA agrees and has revised this AD to include the 
requested change.
    Request: Bell stated that Bell Alert Service Bulletin 412-13-156, 
dated

[[Page 7654]]

April 25, 2013 (ASB 412-13-156) related to P/N 412-375-079-101 only and 
that inverter P/N 412-375-079-103 would eventually replace inverter P/N 
412-375-079-101 but was not part of ASB 412-13-156's method of 
compliance. Bell stated the NPRM did not match the ASB.
    FAA Response: The FAA disagrees because ASB 412-13-156's method of 
compliance appears to include replacing inverter P/N 412-375-079-101 
with inverter P/N 412-375-079-103. Paragraph 9 of ASB 412-13-156 
states, ``Remove the affected inverter and replace with inverter P/N 
412-375-079-103[.]''
    Request: Bell requested that the FAA add more information in the 
Discussion paragraph regarding an alternative method of compliance 
(AMOC) issued to AD 2015-04-04. Bell requested this information should 
include Bell Alert Service Bulletin 412-15-164, dated March 13, 2015 
(ASB 412-15-164), which was issued to notify individuals that an AMOC 
to AD 2015-04-04, was available. Bell ASB 412-15-164 specifies the FAA-
approved AMOC, which allows instrument flight rules (IFR) and night 
operations provided the helicopter is flown by two pilots.
    FAA Response: The FAA agrees and has revised the information in the 
Related Service Information section.
    Request: Bell requested the FAA clarify a statement in the NPRM 
that Bell notified the FAA that ASB 412-16-171 contained errors in the 
serial numbers listed in Part B.
    FAA Response: The FAA agrees. The FAA noticed an error in the 
serial numbers listed in ASB 412-16-171, Part B, and reached out to 
Bell for clarification. The FAA received an email from Bell dated 
August 29, 2017, confirming the existence of an error. The email from 
Bell stated: ``There is an error in Part B. According to the 
`Helicopters Affected' block, helicopters 36696 through 36999 and 37013 
through subsequent have the intent of the bulletin accomplished prior 
to delivery therefore, Part B should read: Part B is applicable to 
helicopters 36248 through 36695 and 37002 through 37012.''

FAA's Determination

    The FAA has reviewed the relevant information and determined that 
an unsafe condition exists and is likely to exist or develop on other 
helicopters of these same type designs and that air safety and the 
public interest require adopting the AD requirements as proposed with 
the changes described previously. These changes are consistent with the 
intent of the proposals in the NPRM and will not increase the economic 
burden on any operator nor increase the scope of the AD.

Related Service Information

    The FAA reviewed Bell ASB 412-15-164, which specifies an AMOC 
approved by the FAA for AD 2015-04-04. Instead of the flight 
limitations mandated by AD 2015-04-04, ASB 412-15-164 limits allow 
operation under IFR and night operations with two pilots.
    The FAA reviewed Bell ASB 412-16-171, which specifies replacing 
certain serial-numbered inverters P/N 412-375-079-101 and 412-375-079-
103 with inverter P/N 412-375-079-105 as a direct replacement or with a 
retrofit kit. Bell specifies that completing the actions specified by 
the ASB constitute terminating action for Bell ASB 412-15-164.
    The FAA also reviewed Bell Service Instruction for Inverter 
Retrofit Kit BHT-412-SI-93, dated February 15, 2016, which provides 
instructions for installing retrofit kit P/N 412-704-058-103.

Costs of Compliance

    The FAA estimates that this AD affects 73 helicopters of U.S. 
Registry. The FAA estimates that operators may incur the following 
costs in order to comply with this AD. Labor costs are estimated at $85 
per work-hour.
    Installing an inverter or retrofit kit requires about 3 work-hours 
and parts cost about $15,749, for an estimated cost of $16,004 per 
helicopter and $1,168,292 for the U.S. fleet.

Differences Between This AD and the Service Information

    Bell ASB 412-16-171 requires compliance no later than January 1, 
2017, while this AD requires compliance within 25 hours TIS. Bell ASB 
412-16-171 makes an ELA a determining factor for corrective actions. 
This proposed AD makes no such requirement. Bell ASB 412-16-171 
provides instructions for helicopters with serial numbers 36649, 36658, 
36659, 36673, 36681 through 36684, 36686, 36688, 36690, 36692, 36694, 
and 36696 through 36704, and this AD does not. Bell has notified the 
FAA of errors in the S/Ns listed for Part B of ASB 412-16-171. 
Accordingly, this AD is only applicable to those serial-numbered 
helicopters subject to the unsafe condition.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, General requirements. 
Under that section, Congress charges the FAA with promoting safe flight 
of civil aircraft in air commerce by prescribing regulations for 
practices, methods, and procedures the Administrator finds necessary 
for safety in air commerce. This regulation is within the scope of that 
authority because it addresses an unsafe condition that is likely to 
exist or develop on products identified in this rulemaking action.

Regulatory Findings

    The FAA has determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    The FAA prepared an economic evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by removing Airworthiness Directive (AD) 
2015-04-04, Amendment 39-18106 (80 FR 9594, February 24, 2015), and 
adding the following new AD:


[[Page 7655]]


2020-02-11 Bell Helicopter Textron Inc.: Amendment 39-21024; Docket 
No. FAA-2017-0052; Product Identifier 2016-SW-081-AD.

(a) Effective Date

    This AD is effective March 17, 2020.

(b) Applicability

    This AD applies to Model 412 and 412EP helicopters with serial 
number (S/N) 33001 through 33213, 34001 through 34036, 36001 through 
36648, 36650 through 36657, 36660 through 36672, 36674 through 
36680, 36685, 36687, 36689, 36691, 36693, 36695, and 37002 through 
37012, certificated in any category, with a static inverter 
(inverter) part number (P/N) 412-375-079-101 or 412-375-079-103 with 
S/N 29145 or higher, installed.

(c) Unsafe Condition

    This AD defines the unsafe condition as the failure of an 
inverter under instrument meteorological conditions or night flight. 
This condition could result in smoke in the cockpit, increased pilot 
workload due to the loss of primary flight and navigation displays, 
alternating current powered engine and transmission indicators, and 
autopilot, and subsequent loss of control of the helicopter.

(d) Affected ADs

    This AD replaces AD 2015-04-04, Amendment 39-18106 (80 FR 9594, 
February 24, 2015).

(e) Compliance

    You are responsible for performing each action required by this 
AD within the specified compliance time unless it has already been 
accomplished prior to that time.

(f) Required Actions

    (1) Within 25 hours time-in-service:
    (i) For helicopters with S/N 33001 through 33213, 34001 through 
34036, and 36001 through 36086, replace the inverter with inverter 
P/N 412-375-079-105.
    (ii) For helicopters with a S/N 36087 through 36648, 36650 
through 36657, 36660 through 36672, 36674 through 36680, 36685, 
36687, 36689, 36691, 36693, 36695, and 37002 through 37012, install 
retrofit kit P/N 412-704-058-103 and replace the inverter with 
inverter P/N 412-375-079-105.
    (2) After accomplishing the actions required by paragraph (f)(1) 
of this AD, you may remove the placard and Rotorcraft Flight Manual 
limitations, required by AD 2015-04-04, prohibiting night operations 
and restricting flights to visual flight rules.
    (3) After the effective date of this AD, do not install an 
inverter P/N 412-375-079-101 or 412-375-079-103 on any helicopter.

(g) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, DSCO Branch, may approve AMOCs for this AD. 
Send your proposal to: Tim Beauregard, Aviation Safety Engineer, 
DSCO Branch, AIR-7J0, FAA, 10101 Hillwood Pkwy., Fort Worth, TX 
76177; telephone 817-222-5190; email [email protected].
    (2) For operations conducted under a 14 CFR part 119 operating 
certificate or under 14 CFR part 91, subpart K, the FAA suggests 
that you notify your principal inspector, or lacking a principal 
inspector, the manager of the local flight standards district office 
or certificate holding district office before operating any aircraft 
complying with this AD through an AMOC.

(h) Related Information

    For more information about this AD, contact Tim Beauregard, 
Aviation Safety Engineer, DSCO Branch, AIR-7J0, FAA, 10101 Hillwood 
Pkwy., Fort Worth, TX 76177; telephone 817-222-5190; email 
[email protected].

    Issued in Fort Worth, Texas, on January 22, 2020.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification 
Service.
[FR Doc. 2020-02587 Filed 2-10-20; 8:45 am]
 BILLING CODE 4910-13-P