[Federal Register Volume 84, Number 242 (Tuesday, December 17, 2019)]
[Proposed Rules]
[Pages 68822-68824]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-27061]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0984; Product Identifier 2019-NM-161-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to supersede Airworthiness Directive (AD) 
2018-16-05, which applies to all The Boeing Company Model 757-200, -
200PF, -200CB, and -300 series airplanes. AD 2018-16-05 requires 
repetitive inspections for skin cracking and shim migration at the 
upper link drag fittings, diagonal brace cracking, and fastener 
looseness; and applicable on-condition actions. Since the FAA issued AD 
2018-16-05, an operator reported finding multiple cracks in the drag 
fitting at fastener holes while inspecting for cracking as required by 
AD 2018-16-05. This proposed AD would retain the actions required by AD 
2018-16-05, reduce the compliance times for certain inspections, and 
add repetitive inspections at certain fastener hole locations and 
applicable on-condition actions. The FAA is proposing this AD to 
address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by January 31, 
2020.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; internet https://www.myboeingfleet.com. You may 
view this service information at the FAA, Transport Standards Branch, 
2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195. It is also 
available on the internet at https://www.regulations.gov by searching 
for and locating Docket No. FAA-2019-0984.

Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0984; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations is listed above. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Chandra Ramdoss, Aerospace Engineer, 
Airframe Section, FAA, Los Angeles ACO Branch, 3960 Paramount 
Boulevard, Lakewood, CA 90712-4137; phone: 562-627-5239; fax: 562-627-
5210; email: [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2019-0984; 
Product Identifier 2019-NM-161-AD'' at the beginning of your comments. 
The FAA specifically invites comments on the overall regulatory, 
economic, environmental, and energy aspects of this NPRM. The FAA will 
consider all comments received by the closing date and may amend this 
NPRM because of those comments.
    The FAA will post all comments, without change, to https://www.regulations.gov, including any personal information you provide. 
The FAA will also post a report summarizing each substantive verbal 
contact the agency receives about this proposed AD.

Discussion

    The FAA issued AD 2018-16-05, Amendment 39-19345 (83 FR 38250, 
August 6, 2018) (``AD 2018-16-05''), for all The Boeing Company Model 
757-200, -200PF, -200CB, and -300 series airplanes. AD 2018-16-05 
requires repetitive inspections for skin cracking and shim migration at 
the upper link drag fittings, diagonal brace cracking, and fastener 
looseness; and applicable on-condition actions. AD 2018-16-05 resulted 
from reports of bolt rotation in the engine drag fitting joint and 
fastener heads; an inspection of the fastener holes revealed that 
cracks were found in the skin on two airplanes. The FAA issued AD 2018-
16-05 to address cracking in the wing upper skin and forward drag 
fittings, which could lead to a compromised upper link and reduced 
structural integrity of the engine strut.

Actions Since AD 2018-16-05 Was Issued

    Since the FAA issued AD 2018-16-05, an operator reported finding 
multiple cracks in the drag fitting at the fastener holes while 
inspecting for cracking as required by AD 2018-16-05. Subsequent 
analysis determined that additional repetitive open-hole high frequency 
eddy current (HFEC) inspections for cracking are necessary at the 
forward rows of fastener holes. Based on findings, it was also 
determined that more frequent inspections for cracking in the diagonal 
brace and diagonal brace fittings are necessary.

Related Service Information Under 1 CFR Part 51

    The FAA reviewed Boeing Alert Requirements Bulletin 757-57A0073 RB, 
Revision 1, dated August 1, 2019. This service information describes 
procedures for repetitive inspections,

[[Page 68823]]

including general visual, detailed, and HFEC inspections, for loose 
fasteners, skin cracking, and shim migration at the upper link drag 
fittings and for cracking in the diagonal brace and diagonal brace 
fittings and applicable on-condition actions. This service information 
is reasonably available because the interested parties have access to 
it through their normal course of business or by the means identified 
in the ADDRESSES section.

FAA's Determination

    The FAA is proposing this AD because the FAA evaluated all the 
relevant information and determined the unsafe condition described 
previously is likely to exist or develop in other products of the same 
type design.

Proposed AD Requirements

    Although this proposed AD does not explicitly restate the 
requirements of AD 2018-16-05, this proposed AD would retain all of the 
requirements of AD 2018-16-05. Those requirements are referenced in the 
service information identified previously, which, in turn, is 
referenced in paragraph (g) of this proposed AD. This proposed AD would 
also require accomplishment of the actions identified in the 
Accomplishment Instructions of Boeing Alert Requirements Bulletin 757-
57A0073 RB, Revision 1, dated August 1, 2019, described previously.
    For information on the procedures and compliance times, see this 
service information at https://www.regulations.gov by searching for and 
locating Docket No. FAA-2019-0984.

Explanation of Requirements Bulletin

    The FAA worked in conjunction with industry, under the 
Airworthiness Directive Implementation Aviation Rulemaking Committee 
(AD ARC), to enhance the AD system. One enhancement is a process for 
annotating which steps in the service information are ``required for 
compliance'' (RC) with an AD. Boeing has implemented this RC concept 
into Boeing service bulletins.
    In an effort to further improve the quality of ADs and AD-related 
Boeing service information, a joint process improvement initiative was 
worked between the FAA and Boeing. The initiative resulted in the 
development of a new process in which the service information more 
clearly identifies the actions needed to address the unsafe condition 
in the ``Accomplishment Instructions.'' The new process results in a 
Boeing Requirements Bulletin, which contains only the actions needed to 
address the unsafe condition (i.e., only the RC actions).

Costs of Compliance

    The FAA estimates that this proposed AD affects 561 airplanes of 
U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                                 Cost on U.S.
              Action                    Labor cost        Parts cost      Cost per product        operators
----------------------------------------------------------------------------------------------------------------
Repetitive inspections (retained   83 work-hours x $85              $0  $7,055 per           $3,957,855 per
 actions from AD 2018-16-05).       per hour = $7,055                    inspection cycle.    inspection cycle.
                                    per inspection
                                    cycle.
Repetitive HFEC inspections (new   2 work-hours x $85                0  $170 per inspection  $95,370 per
 proposed action).                  per hour = $170                      cycle.               inspection cycle.
                                    per inspection
                                    cycle.
----------------------------------------------------------------------------------------------------------------

    The FAA has received no definitive data that would enable the FAA 
to provide cost estimates for the on-condition actions specified in 
this proposed AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes and associated appliances to the 
Director of the System Oversight Division.

Regulatory Findings

    The FAA has determined that this proposed AD would not have 
federalism implications under Executive Order 13132. This proposed AD 
would not have a substantial direct effect on the States, on the 
relationship between the national Government and the States, or on the 
distribution of power and responsibilities among the various levels of 
government.
    For the reasons discussed above, I certify that the proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]


0
2. The FAA amends Sec.  39.13 by removing Airworthiness Directive (AD) 
2018-16-05, Amendment 39-19345 (83 FR 38250, August 6, 2018), and 
adding the following new AD:

The Boeing Company: Docket No. FAA-2019-0984; Product Identifier 
2019-NM-161-AD.

[[Page 68824]]

(a) Comments Due Date

    The FAA must receive comments on this AD action by January 31, 
2020.

(b) Affected ADs

    This AD replaces AD 2018-16-05, Amendment 39-19345 (83 FR 38250, 
August 6, 2018) (``AD 2018-16-05'').

(c) Applicability

    This AD applies to all The Boeing Company Model 757-200, -200PF, 
-200CB, and -300 series airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 57, Wings.

(e) Unsafe Condition

    This AD was prompted by reports of bolt rotation in the engine 
drag fitting joint and fastener heads; an inspection of the fastener 
holes revealed that cracks were found in the skin. This AD was also 
prompted by a report of multiple cracks found in the drag fitting at 
fastener holes during inspections required by AD 2018-16-05. The FAA 
is issuing this AD to address cracking in the wing upper skin and 
forward drag fittings, which could lead to a compromised upper link 
and reduced structural integrity of the engine strut.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Except as specified by paragraph (h) of this AD: At the 
applicable times specified in the ``Compliance'' paragraph of Boeing 
Alert Requirements Bulletin 757-57A0073 RB, Revision 1, dated August 
1, 2019, do all applicable actions identified in, and in accordance 
with, the Accomplishment Instructions of Boeing Alert Requirements 
Bulletin 757-57A0073 RB, Revision 1, dated August 1, 2019.
    Note 1 to paragraph (g): Guidance for accomplishing the actions 
required by this AD can be found in Boeing Alert Service Bulletin 
757-57A0073, Revision 1, dated August 1, 2019, which is referred to 
in Boeing Alert Requirements Bulletin 757-57A0073 RB, Revision 1, 
dated August 1, 2019.

(h) Exceptions to Service Information Specifications

    (1) Where Boeing Alert Requirements Bulletin 757-57A0073 RB, 
Revision 1, dated August 1, 2019, uses the phrase ``the Revision 1 
date of Requirements Bulletin 757-57A0073 RB'' this AD requires 
using ``the effective date of this AD.''
    (2) Where Boeing Alert Requirements Bulletin 757-57A0073 RB, 
Revision 1, dated August 1, 2019, specifies contacting Boeing for 
repair instructions: This AD requires doing the repair and 
applicable on-condition actions before further flight using a method 
approved in accordance with the procedures specified in paragraph 
(i) of this AD.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Los Angeles ACO Branch, FAA, has the authority 
to approve AMOCs for this AD, if requested using the procedures 
found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your 
request to your principal inspector or local Flight Standards 
District Office, as appropriate. If sending information directly to 
the manager of the certification office, send it to the attention of 
the person identified in paragraph (j)(1) of this AD. Information 
may be emailed to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by The Boeing Company Organization Designation 
Authorization (ODA) that has been authorized by the Manager, Los 
Angeles ACO Branch, FAA, to make those findings. To be approved, the 
repair method, modification deviation, or alteration deviation must 
meet the certification basis of the airplane, and the approval must 
specifically refer to this AD.
    (4) AMOCs approved previously for AD 2018-16-05 are not approved 
as AMOCs for this AD.

(j) Related Information

    (1) For more information about this AD, contact Chandra Ramdoss, 
Aerospace Engineer, Airframe Section, FAA, Los Angeles ACO Branch, 
3960 Paramount Boulevard, Lakewood, CA 90712-4137; phone: 562-627-
5239; fax: 562-627-5210; email: [email protected].
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; internet https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA, Transport Standards Branch, 2200 South 216th 
St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195.

    Issued in Des Moines, Washington, on December 5, 2019.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-27061 Filed 12-16-19; 8:45 am]
 BILLING CODE 4910-13-P