[Federal Register Volume 84, Number 150 (Monday, August 5, 2019)]
[Rules and Regulations]
[Pages 37957-37959]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-16701]



 ========================================================================
 Rules and Regulations
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains regulatory documents 
 having general applicability and legal effect, most of which are keyed 
 to and codified in the Code of Federal Regulations, which is published 
 under 50 titles pursuant to 44 U.S.C. 1510.
 
 The Code of Federal Regulations is sold by the Superintendent of Documents. 
 
 ========================================================================
 

  Federal Register / Vol. 84, No. 150 / Monday, August 5, 2019 / Rules 
and Regulations  

[[Page 37957]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0255; Product Identifier 2019-NM-018-AD; Amendment 
39-19687; AD 2019-14-09]
RIN 2120-AA64


Airworthiness Directives; Airbus SAS Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all 
Airbus SAS Model A330-200 Freighter series airplanes. This AD was 
prompted by reports of cracked flexible hoses of the oxygen crew and 
courier distribution system (OCCDS) on A330 freighter airplanes. This 
AD requires repetitive detailed inspections, including functional 
testing, of the OCCDS and replacement of affected part(s) if necessary, 
as specified in a European Aviation Safety Agency (EASA) AD, which is 
incorporated by reference. The FAA is issuing this AD to address the 
unsafe condition on these products.

DATES: This AD is effective September 9, 2019.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of September 9, 
2019.

ADDRESSES: For the material incorporated by reference (IBR) in this AD, 
contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; 
telephone +49 221 89990 1000; email [email protected]; internet 
www.easa.europa.eu. You may find this IBR material on the EASA website 
at https://ad.easa.europa.eu. You may view this IBR material at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. 
For information on the availability of this material at the FAA, call 
206-231-3195. It is also available in the AD docket on the internet at 
http://www.regulations.gov by searching for and locating Docket No. 
FAA-2019-0255.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0255; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this final rule, the regulatory evaluation, any comments received, and 
other information. The address for Docket Operations is U.S. Department 
of Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer, 
International Section, Transport Standards Branch, FAA, 2200 South 
216th St., Des Moines, WA 98198; telephone and fax 206-231-3229.

SUPPLEMENTARY INFORMATION:

Discussion

    The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 
CFR part 39 by adding an AD that would apply to all Airbus SAS Model 
A330-200 Freighter series airplanes. The NPRM published in the Federal 
Register on May 7, 2019 (84 FR 19891). The NPRM was prompted by reports 
of cracked flexible hoses of the OCCDS on A330 freighter airplanes. The 
NPRM proposed to require repetitive detailed inspections, including 
functional testing, of the OCCDS and replacement of affected part(s) if 
necessary.
    The FAA is issuing this AD to address cracked oxygen hoses. This 
condition, if not addressed, could lead to oxygen leakage in the 
flexible hose of the OCCDS, which, in combination with in-flight 
depressurization, smoke in the flight deck, or a smoke evacuation 
procedure, could result in crew injury and reduced control of the 
airplane.
    The EASA, which is the Technical Agent for the Member States of the 
European Union, has issued EASA AD 2019-0027, dated February 4, 2019 
(``EASA AD 2019-0027'') (referred to after this as the Mandatory 
Continuing Airworthiness Information, or ``the MCAI''), to correct an 
unsafe condition for all Airbus SAS Model A330-200 Freighter series 
airplanes. The MCAI states:

    Several occurrences were reported of finding cracked flexible 
hoses [part number] P/N 32209-series of the OCCDS on A330 freighter 
aeroplanes. These flexible hoses are steel braided hoses with 
polyurethane (PUR) inner tubes and steel inner springs. On A330 
freighter aeroplanes, these hoses are located in the courier area 
and are not pressurized during normal operation.
    This condition, if not detected and corrected, could lead to 
oxygen leakage in the flexible hose of the OCCDS, which, in 
combination with in-flight depressurization, smoke in cockpit or 
smoke evacuation procedure, could possibly result in cockpit crew 
injury and reduced control of the aeroplane.
    To address this potential unsafe condition, Airbus issued the SB 
[service bulletin] to provide inspection instructions.
    For the reasons described above, this [EASA] AD requires 
repetitive detailed inspections (DET), including functional testing, 
of the OCCDS and, depending on findings, replacement of affected 
part(s).

    You may examine the MCAI in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0255.

Comments

    The FAA gave the public the opportunity to participate in 
developing this final rule. The FAA received no comments on the NPRM or 
on the determination of the cost to the public.

Conclusion

    The FAA reviewed the relevant data and determined that air safety 
and the public interest require adopting this final rule as proposed, 
except for minor editorial changes. The FAA has determined that these 
minor changes:
     Are consistent with the intent that was proposed in the 
NPRM for addressing the unsafe condition; and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM.

Related IBR Material Under 1 CFR Part 51

    EASA AD 2019-0027 describes procedures for repetitive inspections 
and replacement of OCCDS flexible

[[Page 37958]]

hoses. This material is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

Costs of Compliance

    The FAA estimates that this AD affects 5 airplanes of U.S. 
registry. The FAA estimates the following costs to comply with this AD:

                                      Estimated Costs For Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per      Cost on  U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
14 work-hours x $85 per hour = $1,190........................              $0           $1,190           $5,950
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, some or all of the costs of this AD 
may be covered under warranty, thereby reducing the cost impact on 
affected individuals. The FAA does not control warranty coverage for 
affected individuals. As a result, the FAA has included all known costs 
in the cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This AD is issued in accordance with authority delegated by the 
Executive Director, Aircraft Certification Service, as authorized by 
FAA Order 8000.51C. In accordance with that order, issuance of ADs is 
normally a function of the Compliance and Airworthiness Division, but 
during this transition period, the Executive Director has delegated the 
authority to issue ADs applicable to transport category airplanes and 
associated appliances to the Director of the System Oversight Division.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2019-14-09 Airbus SAS: Amendment 39-19687; Docket No. FAA-2019-0255; 
Product Identifier 2019-NM-018-AD.

(a) Effective Date

    This AD is effective September 9, 2019.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all Airbus SAS Model A330-223F and -243F 
airplanes, certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 35, Oxygen.

(e) Reason

    This AD was prompted by reports of cracked flexible hoses of the 
oxygen crew and courier distribution system (OCCDS) on A330 
freighter airplanes. The FAA is issuing this AD to address cracked 
oxygen hoses. This condition, if not addressed, could lead to oxygen 
leakage in the flexible hose of the OCCDS, which, in combination 
with in-flight depressurization, smoke in the flight deck, or a 
smoke evacuation procedure, could result in crew injury and reduced 
control of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Requirements

    Except as specified in paragraph (h) of this AD: Comply with all 
required actions and compliance times specified in, and in 
accordance with, European Aviation Safety Agency (EASA) AD 2019-
0027, dated February 4, 2019 (``EASA AD 2019-0027'').

(h) Exceptions to EASA AD 2019-0027

    (1) For purposes of determining compliance with the requirements 
of this AD: Where EASA AD 2019-0027 refers to its effective date, 
this AD requires using the effective date of this AD.
    (2) The ``Remarks'' section of EASA AD 2019-0027 does not apply 
to this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (j) of this AD. Information may 
be emailed to: [email protected]. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain instructions from a manufacturer, the instructions must be 
accomplished using a method approved

[[Page 37959]]

by the Manager, International Section, Transport Standards Branch, 
FAA; or EASA; or Airbus SAS's EASA Design Organization Approval 
(DOA). If approved by the DOA, the approval must include the DOA-
authorized signature.
    (3) Required for Compliance (RC): For any service information 
referenced in EASA AD 2019-0027 that contains RC procedures and 
tests: Except as required by paragraph (i)(2) of this AD, RC 
procedures and tests must be done to comply with this AD; any 
procedures or tests that are not identified as RC are recommended. 
Those procedures and tests that are not identified as RC may be 
deviated from using accepted methods in accordance with the 
operator's maintenance or inspection program without obtaining 
approval of an AMOC, provided the procedures and tests identified as 
RC can be done and the airplane can be put back in an airworthy 
condition. Any substitutions or changes to procedures or tests 
identified as RC require approval of an AMOC.

(j) Related Information

    For more information about this AD, contact Vladimir Ulyanov, 
Aerospace Engineer, International Section, Transport Standards 
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone 
and fax 206-231-3229.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless this AD specifies otherwise.
    (i) European Aviation Safety Agency (EASA) AD 2019-0027, dated 
February 4, 2019.
    (ii) [Reserved]
    (3) For EASA AD 2019-0027, contact the EASA, Konrad-Adenauer-
Ufer 3, 50668 Cologne, Germany; telephone +49 221 89990 6017; email 
[email protected]; Internet www.easa.europa.eu. You may find this 
EASA AD on the EASA website at https://ad.easa.europa.eu.
    (4) You may view this EASA AD at the FAA, Transport Standards 
Branch, 2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195. EASA AD 
2019-0027 may be found in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-
2019-0255.
    (5) You may view this material that is incorporated by reference 
at the National Archives and Records Administration (NARA). For 
information on the availability of this material at NARA, call 202-
741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Des Moines, Washington, on July 18, 2019.
Suzanne Masterson,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-16701 Filed 8-2-19; 8:45 am]
BILLING CODE 4910-13-P