[Federal Register Volume 84, Number 150 (Monday, August 5, 2019)]
[Proposed Rules]
[Pages 37976-37979]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-16571]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2019-0584; Product Identifier 2019-NM-096-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus Canada Limited Partnership (Type 
Certificate Previously Held by C Series Aircraft Limited Partnership 
(CSALP); Bombardier, Inc.) Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

[[Page 37977]]


ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-
500-1A11 airplanes. This proposed AD was prompted by a determination 
that new or more restrictive airworthiness limitations are necessary. 
This proposed AD would require revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations. The FAA is proposing this AD to 
address the unsafe condition on these products.

DATES: The FAA must receive comments on this proposed AD by September 
19, 2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec 
H4S 1Y9, Canada; telephone: 514-855-5000; fax: 514-855-7401; email: 
[email protected]; internet: http://www.bombardier.com. You 
may view this service information at the FAA, Transport Standards 
Branch, 2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0584; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations is listed above. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Andrea Jimenez, Aerospace Engineer, 
Airframe and Propulsion Section, FAA, New York ACO Branch, 1600 Stewart 
Avenue, Suite 410, Westbury, NY 11590; telephone: 516-228-7330; fax: 
516-794-5531; email: [email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    The FAA invites you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2019-0584; 
Product Identifier 2019-NM-096-AD'' at the beginning of your comments. 
The FAA specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this NPRM. The FAA will 
consider all comments received by the closing date and may amend this 
NPRM because of those comments.
    The FAA will post all comments received, without change, to http://www.regulations.gov, including any personal information you provide. 
The FAA will also post a report summarizing each substantive verbal 
contact received about this NPRM.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian AD CF-2019-14, dated April 5, 
2019 (referred to after this as the Mandatory Continuing Airworthiness 
Information, or ``the MCAI''), to correct an unsafe condition for 
certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500-
1A11 airplanes. The MCAI states:

    The Airworthiness Limitations (AWL) for the BD-500-1A10 and BD-
500-1A11 aeroplanes are defined and published in the CSALP AWL 
publication, approved by Transport Canada. The instructions 
contained in the AWL publication have been identified as mandatory 
actions for continued airworthiness. Failure to comply with these 
instructions could result in an unsafe condition.
    Since these aeroplanes have entered service, Issue No. 008.00 of 
the AWL has been published, including new and/or more restrictive 
items. For the reason described above, this [Canadian] AD mandates 
incorporation of the actions specified in the AWL Issue No. 008.00 
into the aeroplane maintenance schedule.

    You may examine the MCAI in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0584.

Related Service Information Under 1 CFR Part 51

    Bombardier has issued C Series Airworthiness Limitations, BD500-
3AB48-11400-02, Issue 009.00, dated June 6, 2019. This service 
information describes airworthiness limitations for fuel tank systems, 
safe life limits, and certification maintenance requirements. This 
service information is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to a bilateral agreement with the State of Design Authority, the FAA 
has been notified of the unsafe condition described in the MCAI and 
service information referenced above. The FAA is proposing this AD 
because the agency evaluated all the relevant information and 
determined the unsafe condition described previously is likely to exist 
or develop on other products of the same type design.

Proposed Requirements of This NPRM

    This proposed AD would require revising the existing maintenance or 
inspection program, as applicable, to incorporate new or more 
restrictive airworthiness limitations.
    This proposed AD would require revisions to certain operator 
maintenance documents to include new actions (e.g., inspections) and 
Critical Design Configuration Control Limitations (CDCCLs). Compliance 
with these actions and CDCCLs is required by 14 CFR 91.403(c). For 
airplanes that have been previously modified, altered, or repaired in 
the areas addressed by this proposed AD, the operator may not be able 
to accomplish the actions described in the revisions. In this 
situation, to comply with 14 CFR 91.403(c), the operator must request 
approval for an alternative method of compliance according to paragraph 
(i)(1) of this proposed AD.

Costs of Compliance

    The FAA estimates that this proposed AD affects 13 airplanes of 
U.S. registry. The FAA estimates the following costs to comply with 
this proposed AD:
    The FAA has determined that revising the existing maintenance or 
inspection program takes an average of 90 work-hours per operator, 
although the agency recognizes that this number may vary from operator 
to operator. In the past, the FAA has estimated that this action

[[Page 37978]]

takes 1 work-hour per airplane. Since operators incorporate maintenance 
or inspection program changes for their affected fleet(s), the FAA has 
determined that a per-operator estimate is more accurate than a per-
airplane estimate. Therefore, the FAA estimates the total cost per 
operator to be $7,650 (90 work-hours x $85 per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    The FAA is issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes and associated appliances to the 
Director of the System Oversight Division.

Regulatory Findings

    The FAA has determined that this proposed AD would not have 
federalism implications under Executive Order 13132. This proposed AD 
would not have a substantial direct effect on the States, on the 
relationship between the national Government and the States, or on the 
distribution of power and responsibilities among the various levels of 
government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Will not affect intrastate aviation in Alaska, and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Airbus Canada Limited Partnership (Type Certificate Previously Held 
by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.):
    Docket No. FAA-2019-0584; Product Identifier 2019-NM-096-AD.

(a) Comments Due Date

    The FAA must receive comments by September 19, 2019.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus Canada Limited Partnership (Type 
Certificate previously held by C Series Aircraft Limited Partnership 
(CSALP); Bombardier, Inc.) Model BD-500-1A10 and BD-500-1A11 
airplanes, certificated in any category, identified in paragraphs 
(c)(1) and (c)(2) of this AD.
    (1) Model BD-500-1A10 airplanes, serial numbers 50001 and 
subsequent with an original airworthiness certificate or original 
export certificate of airworthiness issued on or before June 6, 
2019.
    (2) Model BD-500-1A11 airplanes, serial numbers 55001 and 
subsequent with an original airworthiness certificate or original 
export certificate of airworthiness issued on or before June 6, 
2019.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Reason

    This AD was prompted by a determination that new or more 
restrictive airworthiness limitations are necessary. The FAA is 
issuing this AD to prevent reduced structural integrity of the 
airplane or reduced controllability of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Maintenance or Inspection Program Revision

    Within 90 days after the effective date of this AD, revise the 
existing maintenance or inspection program, as applicable, to 
incorporate the information specified in Bombardier C Series 
Airworthiness Limitations, BD500-3AB48-11400-02, Issue 009.00, dated 
June 6, 2019. The initial compliance time for doing the tasks is at 
the time specified in Bombardier C Series Airworthiness Limitations, 
BD500-3AB48-11400-02, Issue 009.00, dated June 6, 2019, or within 90 
days after the effective date of this AD, whichever occurs later.

(h) No Alternative Actions, Intervals, or Critical Design Configuration 
Control Limitations (CDCCLs)

    After the existing maintenance or inspection program has been 
revised as required by paragraph (g) of this AD, no alternative 
actions (e.g., inspections), intervals, or CDCCLs may be used unless 
the actions, intervals, and CDCCLs are approved as an alternative 
method of compliance (AMOC) in accordance with the procedures 
specified in paragraph (i)(1) of this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York ACO Branch, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or local Flight Standards District Office, as appropriate. 
If sending information directly to the manager of the certification 
office, send it to ATTN: Program Manager, Continuing Operational 
Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone: 516-228-7300; fax: 516-794-5531. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
local flight standards district office/certificate holding district 
office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO 
Branch, FAA; or Transport Canada Civil Aviation (TCCA); or CSALP's 
TCCA Design Approval Organization (DAO). If approved by the DAO, the 
approval must include the DAO-authorized signature.

(j) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian AD CF-2019-14, dated April 5, 2019, for related 
information. This MCAI may be found in the AD docket on the internet 
at http://www.regulations.gov by searching for and locating Docket 
No. FAA-2019-0584.
    (2) For more information about this AD, contact Andrea Jimenez, 
Aerospace Engineer, Airframe and Propulsion Section, FAA, New York 
ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; 
telephone:

[[Page 37979]]

516-228-7330; fax: 516-794-5531; email: [email protected].
    (3) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone: 514-855-5000; fax: 514-
855-7401; email: [email protected]; internet: http://www.bombardier.com. You may view this service information at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, 
WA. For information on the availability of this material at the FAA, 
call 206-231-3195.

    Issued in Des Moines, Washington, on July 29, 2019.
Dionne Palermo,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2019-16571 Filed 8-2-19; 8:45 am]
 BILLING CODE 4910-13-P