[Federal Register Volume 84, Number 71 (Friday, April 12, 2019)]
[Rules and Regulations]
[Pages 14865-14870]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-07290]
[[Page 14865]]
-----------------------------------------------------------------------
DEPARTMENT OF HEALTH AND HUMAN SERVICES
Food and Drug Administration
21 CFR Parts 876, 878, and 886
[Docket No. FDA-2018-N-3066]
Medical Devices; Classification of Accessories Distinct From
Other Devices; Finalized List of Accessories Suitable for Class I
AGENCY: Food and Drug Administration, HHS.
ACTION: Final classification action.
-----------------------------------------------------------------------
SUMMARY: The Food and Drug Administration (FDA, we, or Agency) is
classifying suitable accessories into class I as required by the FDA
Reauthorization Act of 2017 (FDARA). The Agency has determined that
general controls alone are sufficient to provide reasonable assurance
of safety and effectiveness for these accessories. We made this
determination based on the risks of the accessories when used as
intended with other devices such as the parent or system.
DATES: This final classification action is effective May 13, 2019.
ADDRESSES: For access to the docket to read background documents or
comments received, go to https://www.regulations.gov and insert the
docket number found in brackets in the heading of this final
classification action into the ``Search'' box and follow the prompts,
and/or go to the Dockets Management Staff, 5630 Fishers Lane, Rm. 1061,
Rockville, MD 20852.
FOR FURTHER INFORMATION CONTACT: Ian Ostermiller, Center for Devices
and Radiological Health, Food and Drug Administration, 10903 New
Hampshire Ave., Bldg. 66, Rm. 5454, Silver Spring, MD 20993-0002, 301-
796-5678.
SUPPLEMENTARY INFORMATION:
I. Background
On August 18, 2017, FDARA was signed into law (Pub. L. 115-52).
Section 707 of FDARA amended section 513(f) of the Federal Food, Drug,
and Cosmetic Act (FD&C Act) (21 U.S.C. 360c(f)) and, among other
amendments, created a process for FDA to propose a list of accessories
suitable for distinct classification into class I. Section
513(f)(6)(D)(i) of the FD&C Act mandated that FDA make the first such
proposal within a year of enactment of FDARA, and FDA published that
proposal in the Federal Register of August 17, 2018 (83 FR 41023).
Section 513(f)(6)(D)(i) also requires that FDA publish a final action
classifying suitable accessories into class I within 180 days after the
end of the comment period. This final classification action fulfills
that requirement.
In the proposal, we explained that the classification of each
accessory is based on the risks of the accessory when used as intended
and the level of regulatory controls necessary to provide a reasonable
assurance of safety and effectiveness of the accessory, notwithstanding
the classification of any other device with which such accessory is
intended to be used (see section 513(f)(6)(A) of the FD&C Act).
In general, we considered an accessory to be eligible for
classification into class I distinct from another device if the
accessory: (1) Is not for use in supporting or sustaining human life,
or of substantial importance in preventing impairment to human health;
(2) does not represent a potential unreasonable risk of illness or
injury; and (3) general controls alone would be sufficient to provide a
reasonable assurance of safety and effectiveness of the accessory.
Note that by regulation, design controls apply to class I devices
only if the devices are automated with computer software or are listed
under Sec. 820.30(a)(2)(ii) (21 CFR 820.30(a)(2)(ii)). Thus, if an
accessory is not automated with computer software but would require
design controls to provide reasonable assurance of safety and
effectiveness, we did not consider it eligible for this classification
process.
In this final classification action, we are classifying into class
I all of the accessories that we proposed as suitable for distinct
classification in class I. We are not including additional accessories
in this final classification action, but FDA intends to publish another
proposed list of accessories that may be suitable for distinct
classification into class I in accordance with the statutory deadline
of 5 years from the first such proposal (see 21 U.S.C.
360c(f)(6)(D)(i)).
II. Comments on the Proposal
FDA received comments from industry, trade associations, and
individuals on FDA's proposal. Various comments were regarding topics
that were determined to be outside the scope of this final
classification action. We have considered the remaining comments and
respond briefly to them as follows. The order of response to the
commenters is purely for organizational purposes and does not signify
the comment's value or importance nor the order in which comments were
received. Certain comments are grouped together under a single number
because the subject matter is similar. In several comments, commenters
requested ``guidance'' on various topics, which we have interpreted to
mean additional information rather than FDA guidance within the meaning
of 21 CFR 10.115(b).
(Comment 1) One commenter stated that class I devices should
include a disclaimer that serious harm may result from their improper
use or installation. The commenter believes this will provide an
incentive for patients to ask their doctors about the proper use of
devices because patients may not see device labeling.
(Response) Class I devices are subject to general controls, which
are defined in section 513(h)(1) of the FD&C Act. These general
controls include, but are not limited to, certain labeling requirements
under the FD&C Act and part 801 (21 CFR part 801), among other
provisions. Changes to labeling requirements under the FD&C Act and
part 801 are outside the scope of this final classification action.
(Comment 2) Several commenters suggested that additional product
codes be considered for distinct classification into class I. One of
these commenters believes that many of the accessories listed in the
comment were considered by FDA to have a higher classification solely
due to the risk of the parent device and FDA's previous review
practices. That commenter believes some of these accessories fall under
existing class I classification regulations and should be placed into
class I through this final classification action.
(Response) We have reviewed all product codes suggested for
distinct classification into class I in response to comments and have
determined that additional product codes identified are not appropriate
for this list at the present time for one or more of the following
reasons: (1) The accessory type is already distinctly classified; (2)
the accessory is of a type that is already class I; or (3) insufficient
information was provided to demonstrate that general controls alone
will provide reasonable assurance of safety and effectiveness.
FDA will consider additional product codes for distinct
classification into class I as part of a future proposal in accordance
with the statutory deadline of 5 years from the first such proposal
under section 513(f)(6)(D)(i) of the FD&C Act. If a manufacturer or
importer with marketing authorization for an accessory believes its
accessories are suitable for distinct classification, the manufacturer
or importer can also request a class I designation through an existing
accessory request pursuant to section 513(f)(6)(D)(ii) of the FD&C Act.
(Comment 3) One commenter requested clarification on two of FDA's
[[Page 14866]]
proposed regulations for penile implant surgical accessories and
implanted mechanical/hydraulic urinary continence device surgical
accessories. This includes the identification of product code FAE for
penile implant surgical accessories, and specific edits to the list of
accessories included in FDA's proposal.
(Response) FDA agrees with the commenter. The identified
accessories intended for use with a penile prosthesis under product
codes FAE and FTQ were within FDA's intent, but the proposal did not
make that clear. FDA has also clarified that penile implant surgical
accessories suitable for class I include the cylinder insertion needle,
device placement tool, tubing plug, and blunt needle. Additionally,
implanted mechanical/hydraulic urinary continence device surgical
accessories suitable for class I include the tubing plug and blunt
needle. For both types of accessories, FDA has found that general
controls alone provide a reasonable assurance of safety and
effectiveness.
(Comment 4) Two commenters noted that section III of the proposal
``Policy Clarification for Classification of Certain Accessories Used
in Orthopedic Surgery'' was inconsistent with the risk-based approach
to classification of accessories as outlined in FDARA, and
classification should not be based upon whether or not an instrument is
considered ``general use'' or ``device-specific''. These commenters
also requested that FDA either revert back to ``previous longstanding
practice and treat all manual surgical instruments provided with Class
II or Class III orthopedic implant systems as Class I (510(k)/PMA
[premarket approval application] exempt) devices, in accordance with
their current classification designation'' or publish new
classifications for instruments that carry a higher risk. One commenter
further noted administrative challenges (e.g., tracking recalls, unique
device identifier markings) for those instruments that have taken on
the classification of the parent device and do not carry their own
product code or regulation.
(Response) This policy clarification does not impose new regulatory
requirements upon devices that had previously been cleared or approved,
but rather provides transparency for the Agency's existing policy
concerning classification of certain orthopedic accessories. We agree
that the classification of existing accessories should and must be
based upon the risk of the accessory when used as intended and the
level of regulatory controls necessary to provide a reasonable
assurance of safety and effectiveness of the accessory, notwithstanding
the classification of the parent device, and that the provisions in
section 513(f)(6) of the FD&C Act may be appropriate to distinctly
classify certain orthopedic accessory types. By clarifying how we have
regulated different types of instruments for orthopedic surgery, we
aimed to explain the limited scope of accessories that would be
appropriate for distinct classification through mechanisms outlined in
section 513(f)(6) of the FD&C Act and provide clarity regarding
accessories that fit within existing class I classification
regulations. If an accessory is distinctly classified, a separate
classification regulation will be created. We believe this will support
separate identification of the accessory distinct from the parent
device.
After reviewing the comments, we continue to believe that the
existing policy concerning classification of certain accessories used
in orthopedic surgery should not be changed. Namely, such accessories
are appropriately classified as orthopedic manual surgical instruments
(Sec. 888.4540 (21 CFR 888.4540)) provided they do not meet the
definition of a device-specific orthopedic accessory as outlined in
FDA's proposal and their risk profile and regulatory controls are
commensurate with that of orthopedic manual surgical instruments.
Further, we continue to believe that certain device-specific orthopedic
instruments have new or different risks to health compared to
orthopedic manual surgical instruments, and general controls alone will
not provide reasonable assurance of safety and effectiveness. These
``device-specific'' accessories are specifically designed for
appropriate implantation or placement of the parent device and have
unique dimensions, geometry, or deployment mechanisms. These
accessories are critical for precise and proper placement of the parent
device, and therefore, FDA considers design controls to be an important
element in the regulation of such accessories to ensure appropriate
compatibility between the accessory and the parent device (see Sec.
820.30).
(Comment 5) Two commenters noted that additional guidance should be
provided for manufacturers who wish to seek distinct classification of
orthopedic accessories, namely ``considerations for reclassification of
instruments that have been previously classified through a premarket
submission based on their association with a particular implant
system'' and ``the specific information that FDA would expect to see in
the requests for instrument reclassification, preferably in a
standardized submission format.''
(Response) Although the question pertains to a different provision
than this final classification action, we believe that clarification in
this case may assist manufacturers and FDA staff for future accessory
classification actions. Any manufacturer or importer may submit a
request for appropriate classification of an existing accessory per
section 513(f)(6)(D)(ii) of the FD&C Act. According to FDA's guidance
``Medical Device Accessories: Describing Accessories and Classification
Pathways'' (available at: https://www.fda.gov/downloads/medicaldevices/deviceregulationandguidance/guidancedocuments/ucm429672.pdf), such a
request should include ``[t]he proposed classification of the accessory
(i.e., class I or class II), as well as the current classification,
should also be clearly identified in the cover letter and/or the
request. An Existing Accessory Request should include the necessary
information, based on Least Burdensome principles, to establish the
risk profile of the accessory when used as intended with the identified
parent device. . . . Note that requests for classification of an
accessory in class II must include an initial draft proposal for
special controls, if special controls would be required pursuant to
subsection 513(a)(1)(B) of the FD&C Act.'' Additional information
regarding reclassification processes are described in sections 513(e)
and (f)(3) of the FD&C Act. FDA recommends manufacturers submit a Pre-
Submission if they have specific questions regarding such a request.
More information regarding the Pre-Submission Program can be found in
FDA's guidance entitled ``Requests for Feedback on Medical Device
Submissions: The Pre-Submission Program and Meetings with Food and Drug
Administration Staff'' (available at https://www.fda.gov/downloads/medicaldevices/deviceregulationandguidance/guidancedocuments/ucm311176.pdf).
(Comment 6) One commenter included several comments regarding the
definition of ``device-specific instrument'' that we provided in
section III of the proposal (the ``Policy Clarification for
Classification of Certain Accessories Used in Orthopedic Surgery'').
The commenter noted the definition was vague and sought clarity on what
is meant by ``unique dimensions, geometry, and/or deployment.''
(Response) To provide further clarity regarding how we interpret
``unique dimensions, geometry, and/or
[[Page 14867]]
deployment'' in the definition for device-specific orthopedic
instrument outlined in FDA's proposal, we provide the following
examples to illustrate the types of instruments that we would consider
to be ``device-specific'' and types that are not:
Examples of instruments that would be considered ``device-
specific'':
(1) A screwdriver that mates through a unique geometry or
connection to a specially designed screw, which could not be inserted
by a standard, generally available screwdriver. Such an instrument
would possess a unique geometry that could not be utilized with screws
of industry standard dimensions (such as cortical (HA) and cancellous
(HB) bone screws per ASTM F543 \1\). In contrast, a general use
screwdriver could be used across screws ``from multiple
manufacturers''.
---------------------------------------------------------------------------
\1\ ASTM F543, Standard Specification and Test Methods for
Metallic Medical Bone Screws. For the current edition of the FDA
recognized standard referenced in this document, see the FDA
Recognized Consensus Standards Database, available at: https://www.accessdata.fda.gov/scripts/cdrh/cfdocs/cfStandards/search.cfm.
---------------------------------------------------------------------------
(2) An inserter instrument that is designed to specifically
interface with features of the parent device to allow for insertion of
the device. Such an instrument would possess unique dimensions or
geometry to mate specifically with the parent device. In contrast,
impactors are used to place an implant and do not require a specific
interface with the parent device. These are general use instruments
that could be used across multiple device types and are not based on
unique dimensions, geometry, or deployment of a parent device.
Examples of instruments that would not be considered ``device-
specific'':
(1) Bone taps solely to create a preliminary hole to help guide
subsequent placement of a screw and can be used across multiple screw
types/sizes. These are not based upon unique dimensions, geometry, or
deployment of a parent device.
(2) Reamers are not based upon unique dimensions, geometry, or
deployment of a parent device and can be used across multiple device
types to prepare a site for implantation.
In all such examples, a general use version of the instrument may
still be designed based upon certain dimensions of the parent device
(e.g., according to industry standard screw dimensions). However,
device-specific instruments are designed specifically for use with a
particular parent device based upon ``unique dimensions, geometry, or
deployment'' of the parent device (e.g., sizes that would not be
compatible with industry standard dimensions, or specific features that
are only present on the parent device).
(Comment 7) One commenter proposed an alternative definition for
``device-specific instrument'' as follows: ``A device-specific
orthopedic instrument is considered to be an accessory designed
specifically for appropriate implantation or placement of the parent
device, based upon unique dimensions, geometry, and/or deployment when
the instrument has an intended use or fundamental scientific technology
that differs from those of the generic types of instruments either
listed in the regulation or previously accepted as being contained
within the regulation.''
The commenter notes that these revisions are necessary to avoid the
definition applying to instruments that clearly fall within an existing
class I classification regulation (e.g., Sec. 888.4540), citing a
screwdriver as being an example of such an instrument that could be
interpreted, based upon the definition, to be ``device-specific.''
(Response) FDA does not agree with the proposed additional text
(i.e., ``. . . when the instrument has an intended use or fundamental
scientific technology that differs from those of the generic types of
instruments either listed in the regulation or previously accepted as
being contained within the regulation''). This text suggests that such
instruments could fit under existing class I regulations (i.e., would
exceed the limitation of exemption under 21 CFR 888.9(a) and (b)) but
would subsequently be appropriately regulated under such regulation
following submission of a 510(k)). However, this does not address the
Agency's position that general controls alone are insufficient to
mitigate risks to health. Furthermore, the phrase ``previously accepted
as being contained within the regulation'' is unclear.
We also disagree with the commenter's statement that the definition
as written would result in such a screwdriver being deemed device-
specific, as such an instrument would not be ``based upon unique
dimensions, geometry, and/or deployment'' of the parent device, unless
the parent device (screw) was somehow unique in design (e.g., a screw
head which would not fit a standard screwdriver).
(Comment 8) One commenter posed several specific scenarios to
better understand circumstances under which an accessory would be
deemed ``device-specific,'' such as whether branding makes an accessory
device-specific, whether an accessory remains ``device-specific'' if
used with another device made by a manufacturer, or whether accessories
to be used ``across systems'' applies to systems from the same
manufacturer. Similarly, they asked if a combination of two general
accessories from two different systems could still be considered a
general use accessory.
(Response) In response to the comments, we are clarifying that the
sole presence of a branding statement would not render an accessory
``device-specific'' according to this definition. An accessory for use
with other devices made by a manufacturer may or may not be determined
to be ``device-specific,'' depending on the design of the accessory.
For example, an accessory designed for use for a specific system, i.e.,
across multiple-device sizes within the same family of devices, would
be device-specific if it is designed specifically for appropriate
implantation or placement of the parent device, based upon unique
dimensions, geometry, and/or deployment.
In some cases, an accessory may also be designed for use across
multiple systems from the same manufacturer. Accessories that can be
used across systems from the same manufacturer may or may not be
considered device-specific, depending on technology, design, and
configuration. For example, one manufacturer may have several systems
of intervertebral body fusion devices, with inserter instruments that
are specifically designed to mate with a unique feature on all devices
in the systems and would therefore be considered device-specific. Such
an instrument would possess unique dimensions or geometry to mate
specifically with the parent device.
In contrast, the combination of two general use accessories would
result in a general use accessory. This is because neither accessory
has a design, geometry, and/or deployment suited to a particular device
or device family.
(Comment 9) One commenter sought clarity on how the device-specific
definition should be applied retroactively to previously cleared/
approved orthopedic accessories.
(Response) The definition of ``device-specific'' was intended to
clarify existing policy regarding regulation of orthopedic accessories,
not to establish new policy. If a device was cleared within a 510(k) as
an accessory but appropriately fits into an existing class I
classification regulation based on the policy clarification, this
determination can be documented to file by the manufacturer along with
updating the listing accordingly.
(Comment 10) One commenter provided several comments regarding
[[Page 14868]]
sizing templates, noting that they would meet the definition of
``device-specific'' but are otherwise distinctly classified in a class
I classification regulation (Sec. 888.4800 (21 CFR 888.4800)). This
commenter also included several examples of other devices (e.g.,
sizers, cutting guides, and trials) that would fall under this
classification regulation.
(Response) In recent history, Sec. 888.4800 has been interpreted
to apply to imaging templates used to estimate proper device size prior
to surgery rather than physical trials/sizers to be used in a surgical
procedure. The initial classification panel identified the following
risks to health associated with devices under this classification
regulation: Tissue damage and adverse tissue reaction. Fracture of the
device could injure surrounding tissue and, if device fragments remain
in the tissue, could cause an adverse tissue reaction.
Further review in response to this comment has led FDA to
reconsider the instruments that were to be subject to this
classification regulation. We agree that trials or templates that are
basic sizing devices for proper implant selection may be appropriately
regulated under Sec. 888.4800, despite the recent practice of
regulating these trials with the parent device.
The Agency does not, however, consider cutting guides to fall
within this classification regulation, as Sec. 888.4800 specifically
calls out devices that are used for ``guiding the marking of tissue
before cutting'' but does not expressly include a physical guide to
direct the orientation of a cut. These devices carry a higher risk than
devices simply intended to mark tissues, as in addition to the risk
associated with this classification regulation (i.e., tissue damage and
adverse tissue reaction), an improper physical cut in the tissue leads
to improper placement of the parent device and potential for resulting
device malfunction or failure.
(Comment 11) One commenter sought clarity on the application of
design controls to class I instruments that interface with higher-
classification parent devices. The commenter notes that ``any interface
with a mating instrument (regardless of instrument classification)
would be subject to design controls via requirements for the parent
device.''
(Response) As FDA stated in the proposal, by regulation, design
controls apply to class I devices only if the devices are automated
with computer software or are listed under Sec. 820.30(a)(2)(ii).
(Comment 12) One commenter sought clarity as to whether a risk-
based justification could be utilized in determining if a device is an
accessory to a parent device. While an instrument may have device-
specific features, the risk may be commensurate with that of orthopedic
manual surgical instruments.
(Response) The determination of whether a device meets the
definition of an accessory is not a risk-based decision. We have
outlined in FDA's proposal why we consider devices with features
specific to a parent device to pose additional risk beyond those of
general use orthopedic manual surgical instruments.
(Comment 13) One commenter stated that the definition of ``device-
specific'' instrument is not consistent with FDA's definition of an
accessory as outlined in the guidance document entitled ``Medical
Device Accessories: Describing Accessories and Classification
Pathways.''
(Response) We do not consider the proposed definition for device-
specific instrument to be inconsistent with FDA's definition of an
accessory, as device-specific orthopedic instruments are those designed
specifically for appropriate implantation or placement of the parent
device, based upon unique dimensions, geometry, and/or deployment.
Furthermore, the device-specific orthopedic instrument definition is
derived from the definition of accessories (i.e., in that ``design
specifications are critical to the proper use of the accessory in
supporting, supplementing, and/or augmenting the performance of the
parent device and/or a specific system.'').
(Comment 14) One commenter notes that FDA stated in its proposal
that ``certain device-specific instruments are accessories and require
precise technical specifications or design characteristics to function
as intended to support, supplement or augment the parent device and if
they are not designed appropriately could cause implant malpositioning
or migration,'' and, thus, ``are ineligible for reclassification in
class I.'' The commenter sought clarity as to why other class I exempt
devices would not also ``require precise technical specifications or
design characteristics.''
(Response) We expect that any device would have certain technical
specifications or design characteristics that dictate their
manufacture. However, for some devices, including device-specific
orthopedic instruments, the safety, performance, and dependability of
the device are critical for precise and proper placement of the parent
device. Design controls, among other benefits, increase the likelihood
that the design transferred to production will translate into a device
that is appropriate for its intended use, including precise and proper
placement of the parent.\2\ Therefore, device-specific orthopedic
instruments require the application of design controls for reasonable
assurance of safety and effectiveness.
---------------------------------------------------------------------------
\2\ For more information about design controls, refer to FDA's
guidance document entitled ``Design Control Guidance for Medical
Device Manufacturers,'' available at https://www.fda.gov/downloads/MedicalDevices/DeviceRegulationandGuidance/GuidanceDocuments/ucm070642.pdf.
---------------------------------------------------------------------------
(Comment 15) One commenter asked for examples of what ``other
regulatory controls'' beyond design controls may be necessary to ensure
compatibility, as stated in the proposal.
(Response) Another regulatory control could be, for example,
premarket notification. For these devices for which verification of
compatibility would be necessary, this may be evaluated through
information (e.g., device description, performance testing) provided in
a premarket submission.
(Comment 16) One commenter sought guidance on the type of
information needed to describe a device-specific orthopedic instrument
in premarket submissions, as well as guidance for manufacturers whose
accessories have been reclassified under section 513(f)(6)(D)(ii) of
the FD&C Act. This commenter also suggested that FDA consider
classification of the orthopedic instruments as class I with design
controls.
(Response) The commenter's requests are outside the scope of this
final classification action.
(Comment 17) One commenter noted that one of the proposed
accessories for classification into class I is a handle to an inserter
device for a class III product. They sought further clarity to
determine whether handles for modular orthopedic instruments could be
distinctly classified from their working end.
(Response) The referenced corneal inlay implant device is class
III, and we proposed distinct classification of the associated handles
into class I. Similarly, other such instrument handles associated with
orthopedic devices cleared through 510(k) or PMA could be distinctly
classified from the parent device using mechanisms outlined in section
513(f)(6)(D)(ii) of the FD&C Act.
(Comment 18) One commenter noted that some instruments provided in
sets used during a surgery may not be considered ``accessories'' but
are provided within these sets for ease of processing and access for
the surgeon. Furthermore, some of these instruments may fall under
existing class I classification regulations.
[[Page 14869]]
(Response) We agree with the commenter. Many instruments in
instrument sets would not be considered accessories to the device, and
some accessories may already be distinctly classified in existing class
I classification regulations.
III. Policy Clarification for Classification of Certain Accessories
Used in Orthopedic Surgery
In the proposal, FDA provided a policy clarification for the
regulatory approach for certain accessories used in orthopedic surgery
to distinguish which accessories may be candidates for classification
under section 513(f)(6)(D)(i) of the FD&C Act. This policy
clarification acknowledged that instruments used in orthopedic surgery
span a wide range of complexity, with many ``general use'' instruments
falling within existing class I classification regulations (e.g., Sec.
888.4540), while other ``device-specific'' instruments have
historically been reviewed in the same premarket submission as the
parent device.
In an effort to ensure a common understanding as to which
orthopedic accessories are considered ``device-specific,'' thereby not
falling within an existing class I classification regulation, and which
may be candidates for classification under section 513(f)(6)(D)(i) of
the FD&C Act, we provided the following definition: A device-specific
orthopedic instrument is considered to be an accessory designed
specifically for appropriate implantation or placement of the parent
device, based upon unique dimensions, geometry, and/or deployment. In
these cases, design specifications are critical to the proper use of
the accessory in supporting, supplementing, and/or augmenting the
performance of the parent device and/or a specific system. FDA
considers design controls (see Sec. 820.30) to be an important element
in the regulation of device-specific accessories, among other
regulatory controls, to ensure appropriate compatibility between the
accessory and the parent device. This excludes general use orthopedic
instruments that are provided as a part of a system.
Based upon comments in response to this section of the proposal,
FDA has not altered the policy clarification or definition of device-
specific orthopedic instruments as previously described but has
provided additional clarification and examples in the responses
discussed in section II above. FDA intends to engage with industry
stakeholders on the topic to resolve additional questions regarding the
existing policy or future proposals for distinct classification of
accessories under section 513(f)(6)(D)(ii) of the FD&C Act.
IV. Analysis of Environmental Impact
The Agency has determined under 21 CFR 25.34(b) that this final
classification action is of a type that does not individually or
cumulatively have a significant effect on the human environment.
Therefore, neither an environmental assessment nor an environmental
impact statement is required.
V. Paperwork Reduction Act of 1995
This final classification action refers to previously approved
collections of information. These collections of information are
subject to review by the Office of Management and Budget (OMB) under
the Paperwork Reduction Act of 1995 (44 U.S.C. 3501-3520). The
collections of information in the following FDA regulations and
guidance have been approved by OMB as listed in the following table:
----------------------------------------------------------------------------------------------------------------
OMB control
21 CFR part; guidance; or FDA form Topic No.
----------------------------------------------------------------------------------------------------------------
807, subpart E........................................... Premarket notification............... 0910-0120
814, subparts A through E................................ Premarket approval................... 0910-0231
``De Novo Classification Process (Evaluation of Automatic De Novo classification process....... 0910-0844
Class III Designation)''.
800, 801, and 809........................................ Medical Device Labeling Regulations.. 0910-0485
820...................................................... Current Good Manufacturing Practice 0910-0073
(CGMP); Quality System (QS)
Regulation.
``Medical Device Accessories: Describing Accessories and Medical Device Accessories........... 0910-0823
Classification Pathways for New Accessory Types.''.
``Requests for Feedback on Medical Device Submissions: Q-submissions........................ 0910-0756
The Pre-Submission Program and Meetings with Food and
Drug Administration Staff''.
----------------------------------------------------------------------------------------------------------------
List of Subjects
21 CFR Part 876
Medical devices.
21 CFR Part 878
Medical devices.
21 CFR Part 886
Medical devices, Ophthalmic goods and services.
Therefore, under the Federal Food, Drug, and Cosmetic Act and under
authority delegated to the Commissioner of Food and Drugs, 21 CFR parts
876, 878, and 886 are amended as follows:
PART 876--GASTROENTEROLOGY-UROLOGY DEVICES
0
1. The authority citation for part 876 continues to read as follows:
Authority: 21 U.S.C. 351, 360, 360c, 360e, 360j, 360l, 371.
0
2. Add Sec. 876.1080 to subpart B to read as follows:
Sec. 876.1080 Gastroenterology-urology accessories to a biopsy
instrument.
(a) Identification. A gastroenterology-urology accessory to a
biopsy instrument is an accessory used to remove a specimen of tissue
for microscopic examination by cutting or aspiration. This generic type
of device includes a syringe for specimen aspiration and a biopsy
channel adaptor. This device does not include accessories to biopsy
instruments used in other medical specialty areas.
(b) Classification. Class I (general controls). The device is
exempt from the premarket notification procedures in subpart E of part
807 of this chapter subject to the limitations in Sec. 876.9.
0
3. Add Sec. 876.3500 to subpart D to read as follows:
Sec. 876.3500 Penile implant surgical accessories.
(a) Identification. Penile implant surgical accessories are manual
devices designed to be used for surgical procedures associated with the
implantation of a penile inflatable implant or penile rigidity implant.
This generic type of device includes the cylinder sizer, cylinder
insertion tool
[[Page 14870]]
and needle, device placement tool, connector assembly tool, incision
closing tool, corporeal dilator, tubing passer, measurement tool or
tape, tubing plug, blunt needle, and hemostat shod tubing.
(b) Classification. Class I (general controls). The device is
exempt from the premarket notification procedures in subpart E of part
807 of this chapter subject to the limitations in Sec. 876.9.
0
4. Add Sec. 876.4630 to subpart E to read as follows:
Sec. 876.4630 Ureteral stent accessories.
(a) Identification. Ureteral stent accessories aid in the insertion
of the ureteral stent that is placed into the ureter to provide
ureteral rigidity and allow the passage of urine. This generic type of
device includes the stent positioner, wire guide, and pigtail
straightener.
(b) Classification. Class I (general controls). The device is
exempt from the premarket notification procedures in subpart E of part
807 of this chapter subject to the limitations in Sec. 876.9.
0
5. Add Sec. 876.5012 to subpart F to read as follows:
Sec. 876.5012 Biliary stent, drain, and dilator accessories.
(a) Identification. Biliary stent, drain, and dilator accessories
are manual devices that aid in the introduction and connection of
biliary stents, drains, or dilators. This generic type of device
includes the guiding catheter, pushing catheter, pigtail straightener,
flap protector, nasal transfer tube, and drainage connecting tube.
(b) Classification. Class I (general controls). The device is
exempt from the premarket notification procedures in subpart E of part
807 of this chapter subject to the limitations in Sec. 876.9.
0
6. Add Sec. 876.5100 to subpart F to read as follows:
Sec. 876.5100 Suprapubic catheter accessories.
(a) Identification. Suprapubic catheter accessories are manual
devices that are used to facilitate the placement of a suprapubic
catheter. This generic type of device includes the introducer, access
dilator, and peel-away sheath.
(b) Classification. Class I (general controls). The device is
exempt from the premarket notification procedures in subpart E of part
807 of this chapter subject to the limitations in Sec. 876.9.
0
7. Add Sec. 876.5290 to subpart F to read as follows:
Sec. 876.5290 Implanted mechanical/hydraulic urinary continence
device surgical accessories.
(a) Identification. Implanted mechanical/hydraulic urinary
continence device surgical accessories are manual devices designed to
be used for surgical procedures associated with the implantation of an
implanted mechanical/hydraulic urinary continence device. This generic
type of device includes the measurement tool or tape, connector
assembly tool, tubing plug, incision closing tool, tubing passer, blunt
needle, and hemostat shod tubing.
(b) Classification. Class I (general controls). The device is
exempt from the premarket notification procedures in subpart E of part
807 of this chapter subject to the limitations in Sec. 876.9.
PART 878--GENERAL AND PLASTIC SURGERY DEVICES
0
8. The authority citation for part 878 continues to read as follows:
Authority: 21 U.S.C. 351, 360, 360c, 360e, 360j, 360l, 371.
0
9. Add Sec. 878.5080 to subpart F to read as follows:
Sec. 878.5080 Air-handling apparatus accessory.
(a) Identification. An air-handling apparatus accessory is a
supplementary device that is intended to be used with an air-handling
apparatus for a surgical operating room. This device provides an
interface between the components of the device or can be used to switch
electrical power. This generic type of device includes fittings,
adapters, couplers, remote switches, and footswitches.
(b) Classification. Class I (general controls). The device is
exempt from the premarket notification procedures in subpart E of part
807 of this chapter subject to the limitations in Sec. 878.9.
PART 886--OPHTHALMIC DEVICES
0
10. The authority citation for part 886 continues to read as follows:
Authority: 21 U.S.C. 351, 360, 360c, 360e, 360j, 360l, 371.
0
11. Add Sec. 886.4355 to subpart F to read as follows:
Sec. 886.4355 Corneal inlay inserter handle.
(a) Identification. The corneal inlay inserter handle is a hand-
held device intended to be used as an accessory to a corneal inlay
inserter. The device extends the length of the inlay inserter to aid in
delivering the inlay implant.
(b) Classification. Class I (general controls). The device is
exempt from the premarket notification procedures in subpart E of part
807 of this chapter subject to the limitations in Sec. 886.9.
Dated: April 9, 2019.
Lowell J. Schiller,
Principal Associate Commissioner for Policy.
[FR Doc. 2019-07290 Filed 4-11-19; 8:45 am]
BILLING CODE 4164-01-P