[Federal Register Volume 83, Number 200 (Tuesday, October 16, 2018)]
[Proposed Rules]
[Pages 52171-52173]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2018-22277]


 ========================================================================
 Proposed Rules
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains notices to the public of 
 the proposed issuance of rules and regulations. The purpose of these 
 notices is to give interested persons an opportunity to participate in 
 the rule making prior to the adoption of the final rules.
 
 ========================================================================
 

  Federal Register / Vol. 83, No. 200 / Tuesday, October 16, 2018 / 
Proposed Rules  

[[Page 52171]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2018-0901; Product Identifier 2018-NM-114-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain The Boeing Company Model 737-100, -200, -200C, -300, -400, and 
-500 series airplanes. This proposed AD was prompted by reports that 
frame web and frame integral inboard chord cracking is occurring on 
multiple airplanes in multiple locations below the passenger floor. 
This proposed AD would require repetitive detailed, general visual, and 
high frequency eddy current (HFEC) inspections of the section 43 lower 
lobe frames at certain stations; an inspection to determine if certain 
repairs are installed; and applicable on-condition actions. We are 
proposing this AD to address the unsafe condition on these products.

DATES: We must receive comments on this proposed AD by November 30, 
2018.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; internet https://www.myboeingfleet.com. You may 
view this referenced service information at the FAA, Transport 
Standards Branch, 2200 South 216th St., Des Moines, WA. For information 
on the availability of this material at the FAA, call 206-231-3195. It 
is also available on the internet at http://www.regulations.gov by 
searching for and locating Docket No. FAA-2018-0901.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0901; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this NPRM, the regulatory evaluation, any comments received, 
and other information. The street address for the Docket Office (phone: 
800-647-5527) is in the ADDRESSES section. Comments will be available 
in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Lu Lu, Aerospace Engineer, Airframe 
Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 
98198; phone and fax: 206-231-3525; email: [email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2018-0901; 
Product Identifier 2018-NM-114-AD'' at the beginning of your comments. 
We specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this NPRM. We will consider all 
comments received by the closing date and may amend this NPRM because 
of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    We have received reports indicating that frame web and frame 
integral inboard chord cracking is occurring on multiple airplanes in 
multiple locations below the passenger floor in section 43 from station 
(STA) 380 to STA 520. This condition, if not addressed, could result in 
the failure of one or more frames. The failure of multiple frames or 
the combination of a severed frame and cracks in fuselage chem-milled 
pockets in this area could lead to uncontrolled decompression of the 
airplane.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Alert Service Bulletin 737-53A1361, dated July 
17, 2018. The service information describes procedures for repetitive 
detailed, general visual, and HFEC inspections of the section 43 lower 
lobe frames from STA 380 to STA 520; a general visual inspection to 
determine if certain repairs are installed; and applicable on-condition 
actions. This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishment of the actions 
identified as ``RC'' (required for compliance) in the Accomplishment 
Instructions of Boeing Alert Service Bulletin 737-53A1361, dated July 
17, 2018, described previously, except for any differences identified 
as exceptions in the regulatory text of this proposed AD.
    For information on the procedures and compliance times, see this 
service information at http://www.regulations.gov by searching for and 
locating Docket No. FAA-2018-0901.

[[Page 52172]]

Costs of Compliance

    We estimate that this proposed AD affects 262 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                                Cost on U.S.
          Action                   Labor cost           Parts cost      Cost per product          operators
----------------------------------------------------------------------------------------------------------------
Inspections..............  Up to 84 work-hours x $85              $0  Up to $7,140 per      Up to $1,870,680 per
                            per hour = $7,140 per                      inspection cycle.     inspection cycle.
                            inspection cycle.
----------------------------------------------------------------------------------------------------------------

    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition actions specified in this proposed 
AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes to the Director of the System Oversight 
Division.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

The Boeing Company: Docket No. FAA-2018-0901; Product Identifier 
2018-NM-114-AD.

(a) Comments Due Date

    We must receive comments by November 30, 2018.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 737-100, -200, -
200C, -300, -400, and -500 series airplanes, certificated in any 
category, as identified in Boeing Alert Service Bulletin 737-
53A1361, dated July 17, 2018.

(d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

(e) Unsafe Condition

    This AD was prompted by reports that frame web and frame 
integral inboard chord cracking is occurring on multiple airplanes 
in multiple locations below the passenger floor. We are issuing this 
AD to address frame cracking, which could result in the failure of 
multiple frames or the combination of a severed frame and cracks in 
fuselage chem-milled pockets in this area, which could lead to 
uncontrolled decompression of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    (1) For airplanes identified as Group 1 in Boeing Alert Service 
Bulletin 737-53A1361, dated July 17, 2018: Within 120 days after the 
effective date of this AD, inspect the airplane and do all 
applicable corrective actions using a method approved in accordance 
with the procedures specified in paragraph (i) of this AD.
    (2) For airplanes identified as Groups 2 through 6 in Boeing 
Alert Service Bulletin 737-53A1361, dated July 17, 2018: Except as 
required by paragraph (h) of this AD, at the applicable times 
specified in paragraph 1.E., ``Compliance,'' of Boeing Alert Service 
Bulletin 737-53A1361, dated July 17, 2018, do all applicable actions 
identified as ``RC'' (required for compliance) in, and in accordance 
with, the Accomplishment Instructions of Boeing Alert Service 
Bulletin 737-53A1361, dated July 17, 2018

(h) Exceptions to Service Information Specifications

    (1) For purposes of determining compliance with the requirements 
of this AD: Where Boeing Alert Service Bulletin 737-53A1361, dated 
July 17, 2018, uses the phrase ``the original issue date of this 
service bulletin,'' this AD requires using ``the effective date of 
this AD.''
    (2) Where Boeing Alert Service Bulletin 737-53A1361, dated July 
17, 2018, specifies contacting Boeing for repair instructions or 
contacting Boeing for alternative inspections: This AD requires 
doing the repair, or the alternative inspections and applicable on-
condition actions, using a method approved in accordance with the 
procedures specified in paragraph (i) of this AD.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Los Angeles ACO Branch, FAA, has the authority 
to approve AMOCs

[[Page 52173]]

for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or local Flight Standards District Office, as 
appropriate. If sending information directly to the manager of the 
certification office, send it to the attention of the person 
identified in paragraph (j)(2) of this AD. Information may be 
emailed to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Los Angeles ACO Branch, FAA, to make those findings. To be 
approved, the repair method, modification deviation, or alteration 
deviation must meet the certification basis of the airplane, and the 
approval must specifically refer to this AD.
    (4) Except as required by paragraph (h)(2) of this AD: For 
service information that contains steps that are labeled as RC, the 
provisions of paragraphs (i)(4)(i) and (i)(4)(ii) of this AD apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. If a step or substep is labeled ``RC Exempt,'' then the 
RC requirement is removed from that step or substep. An AMOC is 
required for any deviations to RC steps, including substeps and 
identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(j) Related Information

    (1) For more information about this AD, contact Lu Lu, Aerospace 
Engineer, Airframe Section, FAA, Seattle ACO Branch, 2200 South 
216th St., Des Moines, WA 98198; phone and fax: 206-231-3525; email: 
[email protected].
    (2) For information about AMOCs, contact George Garrido, 
Aerospace Engineer, Airframe Section, FAA, Los Angeles ACO Branch, 
3960 Paramount Boulevard, Lakewood, CA 90712-4137; phone: 562-627-
5232; fax: 562-627-5210; email: [email protected].
    (3) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; internet https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA, Transport Standards Branch, 2200 South 216th 
St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195.

    Issued in Des Moines, Washington, on October 4, 2018.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2018-22277 Filed 10-15-18; 8:45 am]
 BILLING CODE 4910-13-P