[Federal Register Volume 83, Number 112 (Monday, June 11, 2018)]
[Proposed Rules]
[Pages 26884-26887]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2018-12233]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2018-0508; Product Identifier 2018-NM-012-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Airbus Model A350-941 airplanes. This proposed AD was prompted 
by a determination that more restrictive maintenance requirements and 
airworthiness limitations are necessary. This proposed AD would require 
revising the maintenance or inspection program, as applicable, to 
incorporate new or more restrictive maintenance requirements and 
airworthiness limitations. We are proposing this AD to address the 
unsafe condition on these products.

DATES: We must receive comments on this proposed AD by July 26, 2018.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5

[[Page 26885]]

p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Airbus 
SAS, Airworthiness Office--EAL, 1 Rond Point Maurice Bellonte, 31707 
Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 45 
80; email [email protected]; internet http://www.airbus.com. You may view this service information at the FAA, 
Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For 
information on the availability of this material at the FAA, call 206-
231-3195.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0508; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this NPRM, the regulatory evaluation, any comments received, 
and other information. The street address for the Docket Operations 
office (telephone 800-647-5527) is in the ADDRESSES section. Comments 
will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Kathleen Arrigotti, Aerospace 
Engineer, International Section, Transport Standards Branch, FAA, 2200 
South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3218.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2018-0508; 
Product Identifier 2018-NM-012-AD'' at the beginning of your comments. 
We specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this NPRM. We will consider all 
comments received by the closing date and may amend this NPRM based on 
those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this NPRM.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Union, has issued EASA AD 
2018-0004, dated January 9, 2018 (referred to after this as the 
Mandatory Continuing Airworthiness Information, or ``the MCAI''), to 
correct an unsafe condition for all Airbus Model A350-941 airplanes. 
The MCAI states:

    Certification Maintenance Requirements (CMR) for the Airbus 
A350, which are approved by EASA, are currently defined and 
published in the Airbus A350 ALS Part 3 document. These instructions 
have been identified as mandatory for continued airworthiness.
    Failure to accomplish these instructions could result in an 
unsafe condition [which is safety-significant latent failures that 
would, in combination with one or more other specific failures or 
events, result in a hazardous or catastrophic failure condition].
    EASA previously issued [EASA] AD 2017-0029 to require the 
actions as specified in Airbus A350 ALS Part 3 Revision 03.
    Since this [EASA] AD was issued, Airbus published Revision 04 of 
Airbus A350 ALS Part 3, to introduce new and more restrictive CMRs.
    For the reason described above, this [EASA] AD retains the 
requirements of EASA AD 2017-0029, which is superseded, and requires 
accomplishment of the actions specified in the ALS.

    You may examine the MCAI in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0508.

Related Service Information Under 1 CFR Part 51

    Airbus has issued A350 Airworthiness Limitations Section (ALS) Part 
3, Certification Maintenance Requirements (CMR), Revision 04, dated 
December 15, 2017. The service information describes mandatory 
maintenance tasks that operators must perform at specified intervals. 
This service information is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.
    This AD requires revisions to certain operator maintenance 
documents to include new actions (e.g., inspections). Compliance with 
these actions is required by 14 CFR 91.403(c). For airplanes that have 
been previously modified, altered, or repaired in the areas addressed 
by this proposed AD, the operator may not be able to accomplish the 
actions described in the revisions. In this situation, to comply with 
14 CFR 91.403(c), the operator must request approval for an alternative 
method of compliance according to paragraph (i) of this proposed AD. 
The request should include a description of changes to the required 
inspections that will ensure the continued operational safety of the 
airplane.

Differences Between This Proposed AD and the MCAI

    The MCAI specifies that if there are findings from the 
airworthiness limitations section (ALS) inspection tasks, corrective 
actions must be accomplished in accordance with Airbus maintenance 
documentation. However, this proposed AD does not include that 
requirement. Operators of U.S.-registered airplanes are required by 
general airworthiness and operational regulations to perform 
maintenance using methods that are acceptable to the FAA. We consider 
those methods to be adequate to address any corrective actions 
necessitated by the findings of ALS inspections required by this 
proposed AD.

Airworthiness Limitations Based on Type Design

    The FAA recently became aware of an issue related to the 
applicability of ADs that require incorporation of an ALS revision into 
an operator's maintenance or inspection program.
    Typically, when these types of ADs are issued by civil aviation 
authorities of other countries, they apply to all airplanes covered 
under an identified type certificate (TC). The corresponding FAA AD 
typically retains applicability to all of those airplanes.
    In addition, U.S. operators must operate their airplanes in an 
airworthy condition, in accordance with 14 CFR 91.7(a). Included in 
this obligation is the requirement to perform any maintenance or 
inspections specified in the ALS, and in accordance with the ALS as 
specified in 14 CFR 43.16 and 91.403(c), unless an alternative has been 
approved by the FAA.
    When a type certificate is issued for a type design, the specific 
ALS, including revisions, is a part of that type design, as specified 
in 14 CFR 21.31(c).
    The sum effect of these operational and maintenance requirements is 
an obligation to comply with the ALS

[[Page 26886]]

defined in the type design referenced in the manufacturer's conformity 
statement. This obligation may introduce a conflict with an AD that 
requires a specific ALS revision if new airplanes are delivered with a 
later revision as part of their type design.
    To address this conflict, the FAA has approved alternative methods 
of compliance (AMOCs) that allow operators to incorporate the most 
recent ALS revision into their maintenance/inspection programs, in lieu 
of the ALS revision required by the AD. This eliminates the conflict 
and enables the operator to comply with both the AD and the type 
design.
    However, compliance with AMOCs is normally optional, and we 
recently became aware that some operators choose to retain the AD-
mandated ALS revision in their fleet-wide maintenance/inspection 
programs, including those for new airplanes delivered with later ALS 
revisions, to help standardize the maintenance of the fleet. To ensure 
that operators comply with the applicable ALS revision for newly 
delivered airplanes containing a later revision than that specified in 
an AD, we plan to limit the applicability of ADs that mandate ALS 
revisions to those airplanes that are subject to an earlier revision of 
the ALS, either as part of the type design or as mandated by an earlier 
AD.
    This proposed AD therefore applies to all Airbus Model A350-941 
airplanes with an original certificate of airworthiness or original 
export certificate of airworthiness that was issued on or before the 
date of approval of the ALS revision identified in this proposed AD. 
Operators of airplanes with an original certificate of airworthiness or 
original export certificate of airworthiness issued after that date 
must comply with the airworthiness limitations specified as part of the 
approved type design and referenced on the type certificate data sheet.

Costs of Compliance

    We estimate that this proposed AD affects 6 airplanes of U.S. 
registry.
    We estimate the following costs to comply with this proposed AD:
    We have determined that revising the maintenance or inspection 
program takes an average of 90 work-hours per operator, although this 
figure may vary from operator to operator. In the past, we have 
estimated that this action takes 1 work-hour per airplane. Since 
operators incorporate maintenance or inspection program changes for 
their affected fleet(s), we have determined that a per-operator 
estimate is more accurate than a per-airplane estimate. Therefore, we 
estimate the total cost per operator to be $7,650 (90 work-hours x $85 
per work-hour).

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes to the Director of the System Oversight 
Division.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Airbus: Docket No. FAA-2018-0508; Product Identifier 2018-NM-012-AD.

(a) Comments Due Date

    We must receive comments by July 26, 2018.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus Model A350-941 airplanes, certificated 
in any category, with an original certificate of airworthiness or 
original export certificate of airworthiness issued on or before 
December 15, 2017.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Reason

    This AD was prompted by a determination that more restrictive 
maintenance requirements and airworthiness limitations are 
necessary. We are issuing this AD to address safety-significant 
latent failures that would, in combination with one or more other 
specific failures or events, result in a hazardous or catastrophic 
failure condition.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Maintenance or Inspection Program Revision

    Within 90 days after the effective date of this AD, revise the 
maintenance or inspection program, as applicable, to incorporate 
Airbus A350 Airworthiness Limitations Section (ALS) Part 3, 
Certification Maintenance Requirements (CMR), Revision 04, dated 
December 15, 2017. The initial compliance time for accomplishing the 
actions is at the applicable times specified in Airbus A350 
Airworthiness Limitations Section (ALS) Part 3, Certification 
Maintenance Requirements (CMR), Revision 04, dated December 15, 
2017; or within 90 days after the effective date of this AD; 
whichever occurs later.

[[Page 26887]]

(h) No Alternative Actions or Intervals

    After the maintenance or inspection program has been revised as 
required by paragraph (g) of this AD, no alternative actions (e.g., 
inspections) or intervals, may be used unless the actions or 
intervals are approved as an alternative method of compliance (AMOC) 
in accordance with the procedures specified in paragraph (i)(1) of 
this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Section, Transport Standards Branch, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Section, send it to the attention of 
the person identified in paragraph (j)(2) of this AD. Information 
may be emailed to: [email protected]. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, International 
Section, Transport Standards Branch, FAA; or the European Aviation 
Safety Agency (EASA); or Airbus's EASA Design Organization Approval 
(DOA). If approved by the DOA, the approval must include the DOA-
authorized signature.

(j) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) EASA AD 2018-0004, dated January 9, 2018, for related 
information. This MCAI may be found in the AD docket on the internet 
at http://www.regulations.gov by searching for and locating Docket 
No. FAA-2018-0508.
    (2) For more information about this AD, contact Kathleen 
Arrigotti, Aerospace Engineer, International Section, Transport 
Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; 
telephone and fax 206-231-3218.
    (3) For service information identified in this AD, contact 
Airbus SAS, Airworthiness Office--EAL, 1 Rond Point Maurice 
Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; 
fax +33 5 61 93 45 80; email [email protected]; internet http://www.airbus.com. You 
may view this service information at the FAA, Transport Standards 
Branch, 2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195.

    Issued in Des Moines, Washington, on May 31, 2018.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2018-12233 Filed 6-8-18; 8:45 am]
 BILLING CODE 4910-13-P