[Federal Register Volume 83, Number 102 (Friday, May 25, 2018)]
[Proposed Rules]
[Pages 24242-24244]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2018-11269]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2018-0415; Product Identifier 2017-NM-149-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for all 
The Boeing Company Model 737-100, -200, -200C, -300, -400, -500 series 
airplanes. This proposed AD was prompted by the results of a fleet 
survey that revealed cracking in the bulkhead frame web at a certain 
body station. This proposed AD would require repetitive inspections of 
the bulkhead frame web at a certain station, and repair if necessary. 
We are proposing this AD to address the unsafe condition on these 
products.

DATES: We must receive comments on this proposed AD by July 9, 2018.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; 
telephone 562-797-1717; internet https://www.myboeingfleet.com. You may 
view this referenced service information at the FAA, Transport 
Standards Branch, 2200 South 216th St., Des Moines, WA. For information 
on the availability of this material at the FAA, call 206-231-3195. It 
is also available on the internet at http://www.regulations.gov by 
searching for and locating Docket No. FAA-2018-0415.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0415; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this NPRM, the regulatory evaluation, any comments received, 
and other information. The street address for the Docket Office (phone: 
800-647-5527) is in the ADDRESSES section. Comments will be available 
in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: George Garrido, Aerospace Engineer, 
Airframe Section, FAA, Los Angeles ACO Branch, 3960 Paramount 
Boulevard, Lakewood, CA 90712-4137; phone: 562-627-5232; fax: 562-627-
5210; email: [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2018-0415; 
Product Identifier 2017-NM-149-AD'' at the beginning of your comments. 
We specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this NPRM. We will consider all 
comments received by the closing date and may amend this NPRM because 
of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

[[Page 24243]]

Discussion

    We have received a report indicating that the results of a fleet 
survey revealed cracking in the bulkhead frame web at a certain body 
station. Boeing performed a fleet survey on retired Model 737-300 
airplanes and inspected the upper bulkhead frame at station (STA) 
259.5. One airplane had two cracks in the bulkhead frame web at 
fasteners connecting the bulkhead frame web to the outer chord between 
stringers S-11 and S-12 on the right side of the airplane. The cracks 
measured 0.45 inch and 1.7 inches in length, and the airplane had 
accomplished 73,655 total flight cycles at the time of inspection. A 
second airplane, which had accomplished 73,290 total flight cycles at 
the time of inspection, had two cracks in the right side bulkhead frame 
web measuring 1.772 inches and 0.219 inch in length, and one crack in 
the left side bulkhead frame web measuring 1.64 inches. Cracks have 
been reported on a total of five airplanes that had accomplished 60,640 
to 73,655 total flight cycles. The cracks are a result of fatigue 
caused by cyclic pressurization of the fuselage. This condition, if not 
corrected, could result in reduced structural integrity of the 
airplane.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Alert Requirements Bulletin 737-53A1369 RB, 
dated October 12, 2017. The service information describes procedures 
for repetitive high frequency eddy current inspections and low 
frequency eddy current inspections and repair of the STA 259.5 bulkhead 
frame web from the first stiffener above stringers S-10 to S-13, on the 
left and right sides of the airplane. This service information is 
reasonably available because the interested parties have access to it 
through their normal course of business or by the means identified in 
the ADDRESSES section.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishment of the actions 
identified in the Boeing Alert Requirements Bulletin 737-53A1369 RB, 
dated October 12, 2017, described previously, except for any 
differences identified as exceptions in the regulatory text of this 
proposed AD.
    For information on the procedures and compliance times, see this 
service information at http://www.regulations.gov by searching for and 
locating Docket No. FAA-2018-0415.

Explanation of Requirements Bulletin

    The FAA worked in conjunction with industry, under the 
Airworthiness Directives Implementation Aviation Rulemaking Committee 
(AD ARC), to enhance the AD system. One enhancement is a process for 
annotating which steps in the service information are ``required for 
compliance'' (RC) with an AD. Boeing has implemented this RC concept 
into Boeing service bulletins.
    In an effort to further improve the quality of ADs and AD-related 
Boeing service information, a joint process improvement initiative was 
worked between the FAA and Boeing. The initiative resulted in the 
development of a new process in which the service information more 
clearly identifies the actions needed to address the unsafe condition 
in the ``Accomplishment Instructions.'' The new process results in a 
Boeing Requirements Bulletin, which contains only the actions needed to 
address the unsafe condition (i.e., only the RC actions).

Costs of Compliance

    We estimate that this proposed AD affects 411 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                                Cost on U.S.
           Action                  Labor cost         Parts cost      Cost per  product          operators
----------------------------------------------------------------------------------------------------------------
Inspections................  57 work-hours x $85                $0  $4,845 per inspection  $1,991,295 per
                              per hour = $4,845                      cycle.                 inspection cycle.
                              per inspection cycle.
----------------------------------------------------------------------------------------------------------------

    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition actions specified in this proposed 
AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes to the Director of the System Oversight 
Division.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and

[[Page 24244]]

    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

The Boeing Company: Docket No. FAA-2018-0415; Product Identifier 
2017-NM-149-AD.

(a) Comments Due Date

    We must receive comments by July 9, 2018.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all The Boeing Company Model 737-100, -200, -
200C, -300, -400, and -500 series airplanes, certificated in any 
category.

(d) Subject

    Air Transport Association (ATA) of America Code 53; Fuselage.

(e) Unsafe Condition

    This AD was prompted by the results of a fleet survey that 
revealed cracking in the bulkhead frame web at a certain body 
station. We are issuing this AD to detect and correct cracking in 
the station 259.5 bulkhead frame web from the first stiffener above 
stringers S-10 to S-13. Such cracking could result in reduced 
structural integrity of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Required Actions

    Except as required by paragraph (h) of this AD: At the 
applicable times specified in the ``Compliance'' paragraph of Boeing 
Alert Requirements Bulletin 737-53A1369 RB, dated October 12, 2017, 
do all applicable actions identified in, and in accordance with, the 
Accomplishment Instructions of Boeing Alert Requirements Bulletin 
737-53A1369 RB, dated October 12, 2017.

    Note 1 to paragraph (g) of this AD: Guidance for accomplishing 
the actions required by this AD is included in Boeing Alert Service 
Bulletin 737-53A1369, dated October 12, 2017, which is referred to 
in Boeing Alert Requirements Bulletin 737-53A1369 RB, dated October 
12, 2017.

(h) Exceptions to Service Information Specifications

    (1) For purposes of determining compliance with the requirements 
of this AD: Where Boeing Alert Requirements Bulletin 737-53A1369 RB, 
dated October 12, 2017, uses the phrase ``the original issue date of 
Requirements Bulletin 737-53A1369,'' this AD requires using the 
effective date of this AD.
    (2) Where Boeing Alert Requirements Bulletin 737-53A1369 RB, 
dated October 12, 2017, specifies contacting Boeing, this AD 
requires repair using a method approved in accordance with the 
procedures specified in paragraph (i) of this AD.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Los Angeles ACO Branch, FAA, has the authority 
to approve AMOCs for this AD, if requested using the procedures 
found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your 
request to your principal inspector or local Flight Standards 
District Office, as appropriate. If sending information directly to 
the manager of the certification office, send it to the attention of 
the person identified in paragraph (j)(1) of this AD. Information 
may be emailed to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Los Angeles ACO Branch, to make those findings. To be 
approved, the repair method, modification deviation, or alteration 
deviation must meet the certification basis of the airplane, and the 
approval must specifically refer to this AD.

(j) Related Information

    (1) For more information about this AD, contact George Garrido, 
Aerospace Engineer, Airframe Section, FAA, Los Angeles ACO Branch, 
3960 Paramount Boulevard, Lakewood, CA 90712-4137; phone: 562-627-
5232; fax: 562-627-5210; email: [email protected].
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Contractual & Data Services 
(C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-
5600; telephone 562-797-1717; internet https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA, Transport Standards Branch, 2200 South 216th 
St., Des Moines, WA. For information on the availability of this 
material at the FAA, call 206-231-3195.

    Issued in Des Moines, Washington, on May 11, 2018.
Michael Kaszycki,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2018-11269 Filed 5-24-18; 8:45 am]
 BILLING CODE 4910-13-P