[Federal Register Volume 83, Number 94 (Tuesday, May 15, 2018)]
[Notices]
[Pages 22521-22523]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2018-10330]


-----------------------------------------------------------------------

DEPARTMENT OF LABOR

Occupational Safety and Health Administration

[Docket No. OSHA-2006-0028]


MET Laboratories, Inc.: Grant of Expansion of Recognition and 
Modification to the NRTL Program's List of Appropriate Test Standards

AGENCY: Occupational Safety and Health Administration (OSHA), Labor.

ACTION: Notice.

-----------------------------------------------------------------------

SUMMARY: In this notice, OSHA announces its final decision to expand 
the scope of recognition for MET Laboratories, Inc., as a Nationally 
Recognized Testing Laboratory (NRTL). In addition, OSHA announces the 
addition of one test standard to the NRTL Program's List of Appropriate 
Test Standards.

DATES: The expansion of the scope of recognition becomes effective on 
May 15, 2018.

FOR FURTHER INFORMATION CONTACT: Information regarding this notice is 
available from the following sources:
    Press inquiries: Contact Mr. Frank Meilinger, Director, OSHA Office 
of Communications, U.S. Department of Labor; telephone: (202) 693-1999; 
email: [email protected].
    General and technical information: Contact Mr. Kevin Robinson, 
Director, Office of Technical Programs and Coordination Activities, 
Directorate of Technical Support and Emergency Management, Occupational 
Safety and Health Administration, U.S. Department of Labor; telephone: 
(202) 693-2110; email: [email protected]. OSHA's web page includes 
information about the NRTL Program (see http://www.osha.gov/dts/otpca/nrtl/index.html).

[[Page 22522]]


SUPPLEMENTARY INFORMATION:

I. Notice of Final Decision

    OSHA hereby gives notice of the expansion of the scope of 
recognition of MET Laboratories, Inc. (MET), as a NRTL. MET's expansion 
covers the addition of two test standards to its scope of recognition.
    OSHA recognition of a NRTL signifies that the organization meets 
the requirements specified by 29 CFR 1910.7. Recognition is an 
acknowledgment that the organization can perform independent safety 
testing and certification of the specific products covered within its 
scope of recognition and is not a delegation or grant of government 
authority. As a result of recognition, employers may use products 
properly approved by the NRTL to meet OSHA standards that require 
testing and certification of the products.
    The Agency processes applications by a NRTL for initial 
recognition, or for expansion or renewal of this recognition, following 
requirements in Appendix A to 29 CFR 1910.7. This appendix requires 
that the Agency publish two notices in the Federal Register in 
processing an application. In the first notice, OSHA announces the 
application and provides its preliminary finding and, in the second 
notice, the Agency provides its final decision on the application. 
These notices set forth the NRTL's scope of recognition or 
modifications of that scope. OSHA maintains an informational web page 
for each NRTL that details its scope of recognition. These pages are 
available from the Agency's website at http://www.osha.gov/dts/otpca/nrtl/index.html.
    MET submitted an application, dated July 27, 2016, (OSHA-2006-0028-
0042) to expand its recognition to include two additional test 
standards. OSHA staff performed a detailed analysis of the application 
packet and reviewed other pertinent information. OSHA did not perform 
any on-site reviews in relation to this application.
    OSHA published the preliminary notice announcing MET's expansion 
application in the Federal Register on February 21, 2018 (83 FR 7496). 
The Agency requested comments by March 8, 2018, but it received no 
comments in response to this notice. OSHA now is proceeding with this 
final notice to grant expansion of MET's scope of recognition.
    To obtain or review copies of all public documents pertaining to 
MET's application, go to http://www.regulations.gov or contact the 
Docket Office, Occupational Safety and Health Administration, U.S. 
Department of Labor, 200 Constitution Avenue NW, Room N-3653, 
Washington, DC 20210. Docket No. OSHA-2006-0028 contains all materials 
in the record concerning MET's recognition.

II. Final Decision and Order

    OSHA staff examined MET's expansion application, its capability to 
meet the requirements of the test standards, and other pertinent 
information. Based on its review of this evidence, OSHA finds that MET 
meets the requirements of 29 CFR 1910.7 for expansion of its 
recognition, subject to the specified limitation and conditions listed 
below. OSHA, therefore, is proceeding with this final notice to grant 
MET's scope of recognition. OSHA limits the expansion of MET's 
recognition to testing and certification of products for demonstration 
of conformance to the test standards listed, below in Table 1.

          Table 1--List of Appropriate Test Standards for Inclusion in MET's NRTL Scope of Recognition
----------------------------------------------------------------------------------------------------------------
                Test standard                                         Test standard title
----------------------------------------------------------------------------------------------------------------
UL 60947-1..................................  Standard for Low Voltage Switchgear and Controlgear--Part 1:
                                               General Rules.
UL 60947-4-1................................  Standard for Safety Low Voltage Switchgear and Controlgear--Part 4-
                                               1: Contactors and Motor-Starters--Electromechanical Contactors
                                               and Motor-Starters.
----------------------------------------------------------------------------------------------------------------

    In this notice, OSHA also announces the addition of a new test 
standard to the NRTL Program's List of Appropriate Test Standards. 
Table 2, below, lists the test standard that is new to the NRTL 
Program. OSHA has determined that this test standard is an appropriate 
test standard and will include it in the NRTL Program's List of 
Appropriate Test Standards.

         Table 2--Test Standard OSHA Is Adding to the NRTL Program's List of Appropriate Test Standards
----------------------------------------------------------------------------------------------------------------
                Test standard                                         Test standard title
----------------------------------------------------------------------------------------------------------------
UL 60947-4-1................................  Standard for Safety Low Voltage Switchgear and Controlgear--Part 4-
                                               1: Contactors and Motor-Starters--Electromechanical Contactors
                                               and Motor-Starters.
----------------------------------------------------------------------------------------------------------------

    OSHA's recognition of any NRTL for a particular test standard is 
limited to equipment or materials for which OSHA standards require 
third-party testing and certification before using them in the 
workplace. Consequently, if a test standard also covers any products 
for which OSHA does not require such testing and certification, a 
NRTL's scope of recognition does not include these products.
    The American National Standards Institute (ANSI) may approve the 
test standards listed above as American National Standards. However, 
for convenience, the use of the designation of the standards-developing 
organization for the standard as opposed to the ANSI designation may 
occur. Under the NRTL Program's policy (see OSHA Instruction CPL 1-0.3, 
Appendix C, paragraph XIV), any NRTL recognized for a particular test 
standard may use either the proprietary version of the test standard or 
the ANSI version of that standard. Contact ANSI to determine whether a 
test standard is currently ANSI-approved.

A. Conditions

    In addition to those conditions already required by 29 CFR 1910.7, 
MET must abide by the following conditions of the recognition:
    1. MET must inform OSHA as soon as possible, in writing, of any 
change of ownership, facilities, or key personnel, and of any major 
change in its operations as a NRTL, and provide details of the 
change(s);
    2. MET must meet all the terms of its recognition and comply with 
all OSHA

[[Page 22523]]

policies pertaining to this recognition; and
    3. MET must continue to meet the requirements for recognition, 
including all previously published conditions on MET's scope of 
recognition, in all areas for which it has recognition.
    Pursuant to the authority in 29 CFR 1910.7, OSHA hereby expands the 
scope of recognition of MET, subject to the limitation and conditions 
specified above.

III. Authority and Signature

    Loren Sweatt, Deputy Assistant Secretary of Labor for Occupational 
Safety and Health, authorized the preparation of this notice. 
Accordingly, the Agency is issuing this notice pursuant to 29 U.S.C. 
657(g)(2), Secretary of Labor's Order No. 1-2012 (77 FR 3912, Jan. 25, 
2012), and 29 CFR 1910.7.

    Signed at Washington, DC, on May 9, 2018.
Loren Sweatt,
Deputy Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2018-10330 Filed 5-14-18; 8:45 am]
BILLING CODE 4510-26-P