[Federal Register Volume 82, Number 118 (Wednesday, June 21, 2017)]
[Proposed Rules]
[Pages 28271-28274]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2017-12794]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2017-0563; Directorate Identifier 2017-NM-021-AD]
RIN 2120-AA64


Airworthiness Directives; Saab AB, Saab Aeronautics (Formerly 
Known as Saab AB, Saab Aerosystems) Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for all 
Saab AB, Saab Aeronautics Model 340A (SAAB/SF340A) and SAAB 340B 
airplanes. This proposed AD was prompted by the determination that new 
inspection tasks for the drag brace support fitting of the main landing 
gear (MLG) and corrosion prevention and control program (CPCP) related 
tasks are necessary. This proposed AD would require revising the 
maintenance or inspection program, as applicable, to incorporate 
airworthiness limitations, including new inspection tasks for the drag 
brace support fitting of the MLG and to implement CPCP related tasks. 
We are proposing this AD to address the unsafe condition on these 
products.

DATES: We must receive comments on this proposed AD by August 7, 2017.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Saab AB, 
Saab Aeronautics, SE-581 88, Link[ouml]ping, Sweden; telephone +46 13 
18 5591; fax +46 13 18 4874; email [email protected]; 
Internet http://www.saabgroup.com. You may view this referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2017-
0563; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Operations office (telephone 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Shahram Daneshmandi, Aerospace 
Engineer, International Branch, ANM-116, Transport Airplane 
Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; 
telephone: 425-227-1112; fax: 425-227-1149.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2017-0563; 
Directorate Identifier 2017-NM-021-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Union, has issued EASA 
Airworthiness Directive 2017-0033, dated February 17, 2017 (referred to 
after this as the Mandatory Continuing Airworthiness Information, or 
``the MCAI''), to correct an unsafe condition for all Saab AB, Saab 
Aeronautics Model 340A (SAAB/SF340A) and SAAB 340B airplanes. The MCAI 
states:

    The airworthiness limitations and/or certification maintenance 
instructions for SAAB SF340A and 340B, which are

[[Page 28272]]

approved by EASA, are currently defined and published in the SAAB 
SF340A and 340B Airworthiness Limitation Manual (ALM). These 
instructions have been identified as mandatory for continued 
airworthiness.
    Failure to accomplish these instructions could result in an 
unsafe condition [reduced structural integrity of the airplane].
    Recently, Saab AB, Aeronautics issued SAAB SF340A and 340B ALM 
Revision 1, mainly to add new inspection tasks for the Main Landing 
Gear drag brace support fitting, and to implement Corrosion 
Prevention and Control Program related tasks.

    You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2017-
0563.

Related Service Information Under 1 CFR Part 51

    We reviewed SAAB 340 Airworthiness Limitation Manual, Revision 1, 
dated December 1, 2016. The service information describes airworthiness 
limitations, including inspection tasks for the drag brace support 
fitting of the MLG and CPCP related tasks. This service information is 
reasonably available because the interested parties have access to it 
through their normal course of business or by the means identified in 
the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Differences Between This Proposed AD and the MCAI or Service 
Information

    The MCAI specifies that if there are findings from the 
airworthiness limitations section (ALS) inspection tasks, corrective 
actions must be accomplished in accordance with SAAB maintenance 
documentation. However, this proposed AD does not include that 
requirement. Operators of U.S.-registered airplanes are required by 
general airworthiness and operational regulations to perform 
maintenance using methods that are acceptable to the FAA. We consider 
those methods to be adequate to address any corrective actions 
necessitated by the findings of ALS inspections required by this 
proposed AD.
    This proposed AD would require revisions to certain operator 
maintenance documents to include new actions (e.g., inspections) and 
Critical Design Configuration Control Limitations (CDCCLs). Compliance 
with these actions and CDCCLs is required by 14 CFR 91.403(c). For 
airplanes that have been previously modified, altered, or repaired in 
the areas addressed by this proposed AD, the operator may not be able 
to accomplish the actions described in the revisions. In this 
situation, to comply with 14 CFR 91.403(c), the operator must request 
approval for an alternative method of compliance according to paragraph 
(i)(1) of this proposed AD. The request should include a description of 
changes to the required actions that will ensure the continued damage 
tolerance of the affected structure.

Airworthiness Limitations Based on Type Design

    The FAA recently became aware of an issue related to the 
applicability of ADs that require incorporation of an ALS revision into 
an operator's maintenance or inspection program.
    Typically, when these types of ADs are issued by civil aviation 
authorities of other countries, they apply to all airplanes covered 
under an identified type certificate (TC). The corresponding FAA AD 
typically retains applicability to all of those airplanes.
    In addition, U.S. operators must operate their airplanes in an 
airworthy condition, in accordance with 14 CFR 91.7(a). Included in 
this obligation is the requirement to perform any maintenance or 
inspections specified in the ALS, and in accordance with the ALS as 
specified in 14 CFR 43.16 and 91.403(c), unless an alternative has been 
approved by the FAA.
    When a type certificate is issued for a type design, the specific 
ALS, including revisions, is a part of that type design, as specified 
in 14 CFR 21.31(c).
    The sum effect of these operational and maintenance requirements is 
an obligation to comply with the ALS defined in the type design 
referenced in the manufacturer's conformity statement. This obligation 
may introduce a conflict with an AD that requires a specific ALS 
revision if new airplanes are delivered with a later revision as part 
of their type design.
    To address this conflict, the FAA has approved alternative methods 
of compliance (AMOCs) that allow operators to incorporate the most 
recent ALS revision into their maintenance/inspection programs, in lieu 
of the ALS revision required by the AD. This eliminates the conflict 
and enables the operator to comply with both the AD and the type 
design.
    However, compliance with AMOCs is normally optional, and we 
recently became aware that some operators choose to retain the AD-
mandated ALS revision in their fleet-wide maintenance/inspection 
programs, including those for new airplanes delivered with later ALS 
revisions, to help standardize the maintenance of the fleet. To ensure 
that operators comply with the applicable ALS revision for newly 
delivered airplanes containing a later revision than that specified in 
an AD, we plan to limit the applicability of ADs that mandate ALS 
revisions to those airplanes that are subject to an earlier revision of 
the ALS, either as part of the type design or as mandated by an earlier 
AD.
    This proposed AD therefore would apply to Model 340A (SAAB/SF340A) 
and SAAB 340B airplanes with an original certificate of airworthiness 
or original export certificate of airworthiness that was issued on or 
before the date of approval of the ALS revision identified in this 
proposed AD. Operators of airplanes with an original certificate of 
airworthiness or original export certificate of airworthiness issued 
after that date must comply with the airworthiness limitations 
specified as part of the approved type design and referenced on the 
type certificate data sheet.

Costs of Compliance

    We estimate that this proposed AD affects 87 airplanes of U.S. 
registry.
    We estimate the following costs to comply with this proposed AD:

[[Page 28273]]



                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on  U.S.
                Action                         Labor cost           Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Revision of the airplane maintenance    1 work-hour x $85 per                 $0             $85          $7,395
 or inspection program.                  hour = $85.
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Saab AB, Saab Aeronautics (Formerly Known as Saab AB, Saab 
Aerosystems): Docket No. FAA-2017-0563; Directorate Identifier 2017-
NM-021-AD.

(a) Comments Due Date

    We must receive comments by August 7, 2017.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Saab AB, Saab Aeronautics (formerly known as 
Saab AB, Saab Aerosystems) Model 340A (SAAB/SF340A) and SAAB 340B 
airplanes, certificated in any category, with an original 
certificate of airworthiness or original export certificate of 
airworthiness that was issued on or before December 1, 2016.

(d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.

(e) Reason

    This AD was prompted by the determination that new inspection 
tasks for the drag brace support fitting of the main landing gear 
(MLG) and corrosion prevention and control program (CPCP) related 
tasks are necessary. We are issuing this AD to prevent reduced 
structural integrity of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Maintenance or Inspection Program Revision

    Within 30 days after the effective date of this AD: Revise the 
maintenance or inspection program, as applicable, to incorporate 
airworthiness limitations, including inspection tasks for the drag 
brace support fitting of the MLG and CPCP related tasks, specified 
in SAAB 340 Airworthiness Limitation Manual, Revision 1, dated 
December 1, 2016. The compliance time for the initial airworthiness 
limitation tasks is at the applicable compliance time specified in 
SAAB 340 Airworthiness Limitation Manual, Revision 1, dated December 
1, 2016, or within 30 days after the effective date of this AD, 
whichever occurs later.

(h) No Alternative Actions, Intervals, Critical Design Configuration 
Control Limitations (CDCCLs)

    After the maintenance or inspection program, as applicable, has 
been revised as required by paragraph (g) of this AD, no alternative 
actions (e.g., inspections), intervals, and/or CDCCLs may be used 
unless the actions, intervals, and/or CDCCLs are approved as an 
alternative method of compliance (AMOC) in accordance with the 
procedures specified in paragraph (i)(1) of this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or local Flight Standards District Office, as 
appropriate. If sending information directly to the manager of the 
International Branch, send it to the attention of the person 
identified in paragraph (j)(2) of this AD. Information may be 
emailed to: [email protected]. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, International 
Branch, ANM-116, Transport Airplane Directorate, FAA; or the 
European Aviation Safety Agency (EASA); or Saab AB, Saab 
Aeronautics's EASA Design Organization Approval (DOA). If approved 
by the DOA, the approval must include the DOA-authorized signature.

(j) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) EASA Airworthiness Directive 2017-0033, dated February 17, 
2017, for related information. This MCAI may be found in the AD 
docket on the Internet at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2017-0563.
    (2) For more information about this AD, contact Shahram 
Daneshmandi, Aerospace Engineer, International Branch, ANM-116,

[[Page 28274]]

Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, 
WA 98057-3356; telephone: 425-227-1112; fax: 425-227-1149.
    (3) For service information identified in this AD, contact Saab 
AB, Saab Aeronautics, SE-581 88, Link[ouml]ping, Sweden; telephone 
+46 13 18 5591; fax +46 13 18 4874; email 
[email protected]; Internet http://www.saabgroup.com. 
You may view this service information at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue SW., Renton, WA. For information on 
the availability of this material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on June 12, 2017.
Dionne Palermo,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2017-12794 Filed 6-20-17; 8:45 am]
 BILLING CODE 4910-13-P