[Federal Register Volume 82, Number 104 (Thursday, June 1, 2017)]
[Notices]
[Pages 25338-25340]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2017-11239]


-----------------------------------------------------------------------

DEPARTMENT OF LABOR

Occupational Safety and Health Administration

[Docket No. OSHA-2006-0028]


MET Laboratories, Inc.: Applications for Expansion of Recognition 
and Proposed Modification to the NRTL Program's List of Appropriate 
Test Standards

AGENCY: Occupational Safety and Health Administration, Labor.

ACTION: Notice.

-----------------------------------------------------------------------

SUMMARY: In this notice, OSHA announces the applications of MET 
Laboratories, Inc. for expansion of its recognition as a Nationally 
Recognized Testing Laboratory (NRTL) and presents the Agency's 
preliminary finding to grant the applications. Additionally, OSHA 
proposes to add two new test standards to the NRTL Program's List of 
Appropriate Test Standards.

DATES: Submit comments, information, and documents in response to this 
notice, or requests for an extension of time to make a submission, on 
or before June 16, 2017.

ADDRESSES: Submit comments by any of the following methods:
    1. Electronically: Submit comments and attachments electronically 
at http://www.regulations.gov, which is the Federal eRulemaking Portal. 
Follow the instructions online for making electronic submissions.
    2. Facsimile: If submissions, including attachments, are not longer 
than 10 pages, commenters may fax them to the OSHA Docket Office at 
(202) 693-1648.
    3. Regular or express mail, hand delivery, or messenger (courier) 
service: Submit comments, requests, and any attachments to the OSHA 
Docket Office, Docket No. OSHA-2006-0028, Technical Data Center, U.S. 
Department of Labor, 200 Constitution Avenue NW., Room N-3508, 
Washington, DC 20210; telephone: (202) 693-2350 (TTY number: (877) 889-
5627). Note that security procedures may result in significant delays 
in receiving comments and other written materials by regular mail. 
Contact the OSHA Docket Office for information about security 
procedures concerning delivery of materials by express mail, hand 
delivery, or messenger service. The hours of operation for the OSHA 
Docket Office are 10:00 a.m.-2:30 p.m., e.t.
    4. Instructions: All submissions must include the Agency name and 
the OSHA docket number (OSHA-2006-0028). OSHA places comments and other 
materials, including any personal information, in the public docket 
without revision, and these materials will be available online at 
http://www.regulations.gov. Therefore, the Agency cautions commenters 
about submitting statements they do not want made available to the 
public, or submitting comments that contain personal information 
(either about themselves or others) such as Social Security numbers, 
birth dates, and medical data.
    5. Docket: To read or download submissions or other material in the 
docket, go to http://www.regulations.gov or the OSHA Docket Office at 
the address above. All documents in the docket are listed in the http://www.regulations.gov index; however, some information (e.g., 
copyrighted material) is not publicly available to read or download 
through the Web site. All submissions, including copyrighted material, 
are available for inspection at the OSHA Docket Office. Contact the 
OSHA Docket Office for assistance in locating docket submissions.
    6. Extension of comment period: Submit requests for an extension of 
the comment period on or before June 16, 2017 to the Office of 
Technical Programs and Coordination Activities, Directorate of 
Technical Support and Emergency Management, Occupational Safety and 
Health Administration, U.S. Department of Labor, 200 Constitution 
Avenue NW., Room N-3655, Washington, DC 20210, or by fax to (202) 693-
1644.

FOR FURTHER INFORMATION CONTACT: Information regarding this notice is 
available from the following sources:
    Press inquiries: Contact Mr. Frank Meilinger, Director, OSHA Office 
of Communications, U.S. Department of Labor, 200 Constitution Avenue 
NW., Room N-3647, Washington, DC 20210; telephone: (202) 693-1999; 
email: [email protected].
    General and technical information: Contact Mr. Kevin Robinson, 
Director, Office of Technical Programs and Coordination Activities, 
Directorate of Technical Support and Emergency Management, Occupational 
Safety and Health Administration, U.S. Department of Labor, 200 
Constitution Avenue NW., Room N-3655, Washington, DC 20210; phone: 
(202) 693-2110 or email: [email protected].

SUPPLEMENTARY INFORMATION:

I. Notice of the Application for Expansion

    The Occupational Safety and Health Administration is providing 
notice that MET Laboratories, Inc. (MET), is applying for expansion of 
its current recognition as an NRTL. MET requests the addition of three 
test standards to its NRTL scope of recognition.
    OSHA recognition of an NRTL signifies that the organization meets 
the requirements specified in 29 CFR 1910.7. Recognition is an 
acknowledgment that the organization can perform independent safety 
testing and certification of the specific products covered within its 
scope of recognition. Each NRTL's scope of recognition includes (1) the 
type of products the NRTL may test, with each type specified by its 
applicable test standard; and (2) the recognized site(s) that has/have 
the technical capability to perform the product-testing and product-
certification activities for test standards within the NRTL's scope. 
Recognition is not a delegation or grant of government authority; 
however, recognition enables employers to use products approved by the 
NRTL to meet OSHA standards that require product testing and 
certification.
    The Agency processes applications by an NRTL for initial 
recognition and for an expansion or renewal of this recognition, 
following requirements in Appendix A to 29 CFR 1910.7. This appendix 
requires that the Agency publish two notices in the Federal Register in 
processing an application. In the first notice, OSHA announces the 
application and provides its preliminary finding. In the second notice, 
the Agency provides its final decision on the application. These 
notices set forth the NRTL's scope of recognition or modifications of 
that scope. OSHA

[[Page 25339]]

maintains an informational Web page for each NRTL, including MET, which 
details the NRTL's scope of recognition. These pages are available from 
the OSHA Web site at http://www.osha.gov/dts/otpca/nrtl/index.html.
    MET currently has one facility (site) recognized by OSHA for 
product testing and certification, with its headquarters located at: 
MET Laboratories, Inc., 914 West Patapsco Avenue, Baltimore, Maryland 
21230. A complete list of MET's scope of recognition is available at 
https://www.osha.gov/dts/otpca/nrtl/met.html.

II. General Background on the Application

    MET submitted three applications, one dated October 15, 2015 (OSHA-
2006-0028-0031), the second dated March 2, 2016 (OSHA-2006-0028-0032) 
and the third dated March 18, 2016 (OSHA-2006-0028-0033), to expand its 
recognition to include three additional test standards. OSHA staff 
performed a detailed analysis of the application packets and reviewed 
other pertinent information. OSHA did not perform any on-site reviews 
in relation to these applications.
    Table 1 below lists the appropriate test standards found in MET's 
applications for expansion for testing and certification of products 
under the NRTL Program.

  Table 1--Proposed List of Appropriate Test Standards for Inclusion in
                     MET's NRTL Scope of Recognition
------------------------------------------------------------------------
           Test standard                     Test standard title
------------------------------------------------------------------------
UL 2108...........................  Standard for Low Voltage Lighting
                                     Systems.
UL 61010-2-091 *..................  Standard for Safety Requirements for
                                     Electrical Equipment for
                                     Measurement, Control and Laboratory
                                     Use--Part 2-091: Particular
                                     Requirements for Cabinet X-Ray
                                     Systems.
UL 61010-2-081 *..................  Standard for Safety Requirements for
                                     Electrical Equipment for
                                     Measurement, Control and Laboratory
                                     Use--Part 2-081: Particular
                                     Requirements for Automatic and Semi-
                                     Automatic Laboratory Equipment for
                                     Analysis and Other Purposes.
------------------------------------------------------------------------
* Represents the standards that OSHA proposes to add to the NRTL
  Program's List of Appropriate Test Standards.

III. Proposal To Add New Test Standard to the NRTL Program's List of 
Appropriate Test Standards

    Periodically, OSHA will propose to add new test standards to the 
NRTL list of appropriate test standards following an evaluation of the 
test standard document. To qualify as an appropriate test standard, the 
Agency evaluates the document to (1) verify it represents a product 
category for which OSHA requires certification by an NRTL, (2) verify 
the document represents an end product and not a component, and (3) 
verify the document defines safety test specifications (not 
installation or operational performance specifications).
    In this notice, OSHA proposes to add two new test standards to the 
NRTL Program's List of Appropriate Test Standards. Table 2, below, 
lists the test standards that are new to the NRTL Program. OSHA 
preliminarily determined these test standards are appropriate test 
standards and proposes to include them in the NRTL Program's List of 
Appropriate Test Standards. OSHA seeks public comment on this 
preliminary determination.

 Table 2--Test Standards OSHA Is Proposing To Add to the NRTL Program's
                   List of Appropriate Test Standards
------------------------------------------------------------------------
           Test standard                     Test standard title
------------------------------------------------------------------------
UL 61010-2-091....................  Standard for Safety Requirements for
                                     Electrical Equipment for
                                     Measurement, Control and Laboratory
                                     Use--Part 2-091: Particular
                                     Requirements for Cabinet X-Ray
                                     Systems.
UL 61010-2-081....................  Standard for Safety Requirements for
                                     Electrical Equipment for
                                     Measurement, Control and Laboratory
                                     Use--Part 2-081: Particular
                                     Requirements for Automatic and Semi-
                                     Automatic Laboratory Equipment for
                                     Analysis and Other Purposes.
------------------------------------------------------------------------

IV. Preliminary Findings on the Application

    MET submitted acceptable applications for expansion of its scope of 
recognition. OSHA's review of the application file, and pertinent 
documentation, indicate that MET can meet the requirements prescribed 
by 29 CFR 1910.7 for expanding its recognition to include the addition 
of these three test standards for NRTL testing and certification listed 
above. This preliminary finding does not constitute an interim or 
temporary approval of MET's application.
    OSHA welcomes public comment as to whether MET meets the 
requirements of 29 CFR 1910.7 for expansion of its recognition as an 
NRTL. Comments should consist of pertinent written documents and 
exhibits. Commenters needing more time to comment must submit a request 
in writing, stating the reasons for the request. Commenters must submit 
the written request for an extension by the due date for comments. OSHA 
will limit any extension to 10 days unless the requester justifies a 
longer period. OSHA may deny a request for an extension if the request 
is not adequately justified. To obtain or review copies of the exhibits 
identified in this notice, as well as comments submitted to the docket, 
contact the Docket Office, Room N-3508, Occupational Safety and Health 
Administration, U.S. Department of Labor, at the above address. These 
materials also are available online at http://www.regulations.gov under 
Docket No. OSHA-2006-0028.
    OSHA staff will review all comments to the docket submitted in a 
timely manner and, after addressing the issues raised by these 
comments, will recommend to the Assistant Secretary for Occupational 
Safety and Health whether to grant MET's applications for expansion of 
its scope of recognition. The Assistant Secretary will make the final 
decision on granting the applications. In making this decision, the 
Assistant Secretary may undertake other proceedings prescribed in 
Appendix A to 29 CFR 1910.7.
    OSHA will publish a public notice of its final decision in the 
Federal Register.

[[Page 25340]]

Authority and Signature

    Dorothy Dougherty, Deputy Assistant Secretary of Labor for 
Occupational Safety and Health, 200 Constitution Avenue NW., 
Washington, DC 20210, authorized the preparation of this notice. 
Accordingly, the Agency is issuing this notice pursuant to 29 U.S.C. 
657(g)(2), Secretary of Labor's Order No. 1-2012 (77 FR 3912, Jan. 25, 
2012), and 29 CFR 1910.7.

    Signed at Washington, DC, on May 24, 2017.
Dorothy Dougherty,
Deputy Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2017-11239 Filed 5-31-17; 8:45 am]
BILLING CODE 4510-26-P