[Federal Register Volume 81, Number 244 (Tuesday, December 20, 2016)]
[Proposed Rules]
[Pages 92742-92745]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-30021]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2016-9502; Directorate Identifier 2016-NM-128-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain The Boeing Company Model 757-200 and -200PF series airplanes. 
This proposed AD was prompted by an evaluation by the design approval 
holder (DAH) indicating that certain areas of the frame webs are 
subject to widespread fatigue damage (WFD). This proposed AD would 
require high frequency eddy current (HFEC) inspections of the frame 
webs for any open coordinating holes, tooling holes, and insulation 
blanket attachment holes; repair if necessary; and modification of the 
frame webs at all open hole locations, which would terminate the 
repetitive inspections. We are proposing this AD to address the unsafe 
condition on these products.

DATES: We must receive comments on this proposed AD by February 3, 
2017.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.

[[Page 92743]]

    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Data & Services Management, P.O. Box 
3707, MC 2H-65, Seattle, WA 98124-2207; telephone: 206-544-5000, 
extension 1; fax: 206-766-5680; Internet: https://www.myboeingfleet.com. You may view this referenced service information 
at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., 
Renton, WA. For information on the availability of this material at the 
FAA, call 425-227-1221. It is also available on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
9502.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
9502; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Muoi Vuong, Aerospace Engineer, 
Airframe Branch, ANM-120L, FAA, Los Angeles Aircraft Certification 
Office (ACO), 3960 Paramount Boulevard, Lakewood, CA 90712-4137; phone: 
562-627-5205; fax: 562-627-5210; email: [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2016-9502; 
Directorate Identifier 2016-NM-128-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Fatigue damage can occur locally, in small areas or structural 
design details, or globally, in widespread areas. Multiple-site damage 
is widespread damage that occurs in a large structural element such as 
a single rivet line of a lap splice joining two large skin panels. 
Widespread damage can also occur in multiple elements such as adjacent 
frames or stringers. Multiple-site damage and multiple-element damage 
cracks are typically too small initially to be reliably detected with 
normal inspection methods. Without intervention, these cracks will 
grow, and eventually compromise the structural integrity of the 
airplane. This condition is known as widespread fatigue damage. It is 
associated with general degradation of large areas of structure with 
similar structural details and stress levels. As an airplane ages, WFD 
will likely occur, and will certainly occur if the airplane is operated 
long enough without any intervention.
    The FAA's WFD final rule (75 FR 69746, November 15, 2010) became 
effective on January 14, 2011. The WFD rule requires certain actions to 
prevent structural failure due to WFD throughout the operational life 
of certain existing transport category airplanes and all of these 
airplanes that will be certificated in the future. For existing and 
future airplanes subject to the WFD rule, the rule requires that DAHs 
establish a limit of validity (LOV) of the engineering data that 
support the structural maintenance program. Operators affected by the 
WFD rule may not fly an airplane beyond its LOV, unless an extended LOV 
is approved.
    The WFD rule (75 FR 69746, November 15, 2010) does not require 
identifying and developing maintenance actions if the DAHs can show 
that such actions are not necessary to prevent WFD before the airplane 
reaches the LOV. Many LOVs, however, do depend on accomplishment of 
future maintenance actions. As stated in the WFD rule, any maintenance 
actions necessary to reach the LOV will be mandated by airworthiness 
directives through separate rulemaking actions.
    In the context of WFD, this action is necessary to enable DAHs to 
propose LOVs that allow operators the longest operational lives for 
their airplanes, and still ensure that WFD will not occur. This 
approach allows for an implementation strategy that provides 
flexibility to DAHs in determining the timing of service information 
development (with FAA approval), while providing operators with 
certainty regarding the LOV applicable to their airplanes.
    We have received a report indicating that certain Model 757 
airplanes have open coordinating holes, tooling holes, and insulation 
blanket attachment holes in the frame webs that were not filled during 
production. There have been no reports of frame web cracking at open 
hole locations. Cracking was found on a fatigue test article where WFD 
analysis identified the need for the inspection. Open attachment holes, 
if not corrected, could result in fatigue cracking that could adversely 
affect the structural integrity of the airplane.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Alert Service Bulletin 757-53A0103, dated June 
22, 2016. The service information describes procedures for performing 
repetitive HFEC inspections of the frame webs for any open coordinating 
holes, tooling holes, insulation blanket attachment holes; and 
modifying the frame webs between stringers S-20 and S-25. This service 
information is reasonably available because the interested parties have 
access to it through their normal course of business or by the means 
identified in the ADDRESSES section.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in the service information described previously, except as discussed 
under ``Differences Between this Proposed AD and the Service 
Information.'' For information on the procedures and compliance times, 
see this service information at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2016-9502.

Differences Between This Proposed AD and the Service Information

    Boeing Alert Service Bulletin 757-53A0103, dated June 22, 2016, 
specifies to contact the manufacturer for certain instructions, but 
this proposed AD would require accomplishment of repair methods, 
modification deviations, and alteration deviations in one of the 
following ways:
     In accordance with a method that we approve; or

[[Page 92744]]

     Using data that meet the certification basis of the 
airplane, and that have been approved by the Boeing Commercial 
Airplanes Organization Designation Authorization (ODA) whom we have 
authorized to make those findings.

Costs of Compliance

    We estimate that this proposed AD affects 74 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                 Cost on U.S.
              Action                    Labor cost        Parts cost      Cost per product        operators
----------------------------------------------------------------------------------------------------------------
HFEC inspection..................  68 work-hours x $85              $0  $5,780 per           $427,720 per
                                    per hour = $5,780                    inspection cycle.    inspection cycle.
                                    per inspection
                                    cycle.
Modification.....................  1 work-hour x $85            \1\ $0  85.................  85.
                                    per hour = $85.
----------------------------------------------------------------------------------------------------------------
\1\ Parts supplied by the operator.

    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition actions specified in this proposed 
AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

The Boeing Company: Docket No. FAA-2016-9502; Directorate Identifier 
2016-NM-128-AD.

(a) Comments Due Date

    We must receive comments by February 3, 2017.

 (b) Affected ADs

    None.

 (c) Applicability

    This AD applies to The Boeing Company Model 757-200 and -200PF 
series airplanes, certificated in any category, as identified in 
Boeing Alert Service Bulletin 757-53A0103, dated June 22, 2016.

 (d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

 (e) Unsafe Condition

    This AD was prompted by an evaluation by the design approval 
holder (DAH) indicating that the frame webs between stringers S-20 
and S-25 on the left side and right side, from station (STA) 440 to 
STA 820 and from STA 1300 to STA 1701, are subject to widespread 
fatigue damage (WFD). We are issuing this AD to prevent fatigue 
cracking that could adversely affect the reduced structural 
integrity of the airplane.

 (f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

 (g) Repetitive High Frequency Eddy Current (HFEC) Inspections of the 
Frame Webs

    At the applicable time specified in paragraph 1.E., 
``Compliance,'' of Boeing Alert Service Bulletin 757-53A0103, dated 
June 22, 2016, do an HFEC inspection of the frame webs for any crack 
in any open coordinating holes, tooling holes, and insulation 
blanket attachment holes in accordance with the Accomplishment 
Instructions of Boeing Alert Service Bulletin 757-53A0103, dated 
June 22, 2016. If any cracking is found, repair before further 
flight using a method approved in accordance with the procedures 
specified in paragraph (i) of this AD. Repeat the inspection at the 
time specified in paragraph 1.E., ``Compliance,'' of Boeing Alert 
Service Bulletin 757-53A0103, dated June 22, 2016.

 (h) Modification of the Frame Webs

    Before the accumulation of 59,000 total flight cycles, modify 
the frame webs at all open hole locations, in accordance with the 
Accomplishment Instructions of Boeing Alert Service Bulletin 757-
53A0103, dated June 22, 2016. Accomplishment of this modification 
terminates the repetitive inspection requirements of paragraph (g) 
of this AD at the modified locations only.

 (i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Los Angeles Aircraft Certification Office 
(ACO), FAA, has the authority to approve AMOCs for this AD, if 
requested using the procedures found in 14 CFR 39.19. In accordance 
with 14 CFR 39.19, send your request to your principal inspector or 
local Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in paragraph (j)(1) of this AD. 
Information may be emailed to [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager

[[Page 92745]]

of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Los Angeles ACO, to make those findings. To be approved, 
the repair method, modification deviation, or alteration deviation 
must meet the certification basis of the airplane, and the approval 
must specifically refer to this AD.
    (4) Except as required by paragraph (g) of this AD: For service 
information that contains steps that are labeled as Required for 
Compliance (RC), the provisions of paragraphs (i)(4)(i) and 
(i)(4)(ii) of this AD apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. If a step or substep is labeled ``RC Exempt,'' then the 
RC requirement is removed from that step or substep. An AMOC is 
required for any deviations to RC steps, including substeps and 
identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

 (j) Related Information

    (1) For more information about this AD, contact Muoi Vuong, 
Aerospace Engineer, Airframe Branch, ANM-120L, FAA, Los Angeles ACO, 
3960 Paramount Boulevard, Lakewood, CA 90712-4137; phone: 562-627-
5205; fax: 562-627-5210; email: [email protected].
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P. O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone: 206-
544-5000, extension 1; fax: 206-766-5680; Internet: https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on December 2, 2016.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2016-30021 Filed 12-19-16; 8:45 am]
 BILLING CODE 4910-13-P