[Federal Register Volume 81, Number 210 (Monday, October 31, 2016)]
[Notices]
[Pages 75442-75444]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-26203]


-----------------------------------------------------------------------

DEPARTMENT OF LABOR

Occupational Safety and Health Administration

[Docket No. OSHA-2007-0039]


Intertek Testing Services NA, Inc.: Application for Expansion of 
Recognition

AGENCY: Occupational Safety and Health Administration (OSHA), Labor.

ACTION: Notice.

-----------------------------------------------------------------------

SUMMARY: In this notice, OSHA announces the application of Intertek 
Testing Services NA, Inc. for expansion of its recognition as a 
Nationally Recognized Testing Laboratory (NRTL) and presents the 
Agency's preliminary finding to grant the application.

DATES: Submit comments, information, and documents in response to this 
notice, or requests for an extension of time to make a submission, on 
or before November 15, 2016.

ADDRESSES: Submit comments by any of the following methods:
    1. Electronically: Submit comments and attachments electronically 
at http://www.regulations.gov, which is the Federal eRulemaking Portal. 
Follow the instructions online for making electronic submissions.
    2. Facsimile: If submissions, including attachments, are not longer 
than 10 pages, commenters may fax them to the OSHA Docket Office at 
(202) 693-1648.
    3. Regular or express mail, hand delivery, or messenger (courier) 
service: Submit comments, requests, and any attachments to the OSHA 
Docket Office, Docket No. OSHA-2007-0039, Technical Data Center, U.S. 
Department of Labor, 200 Constitution Avenue NW., Room N-3653, 
Washington, DC 20210; telephone: (202) 693-2350 (TTY number: (877) 889-
5627). Note that security procedures may result in significant delays 
in receiving comments and other written materials by regular mail. 
Contact the OSHA Docket Office for information about security 
procedures concerning delivery of materials by express mail, hand 
delivery, or messenger service. The hours of operation for the OSHA 
Docket Office are 8:15 a.m.-4:45 p.m., e.t.
    4. Instructions: All submissions must include the Agency name and 
the OSHA docket number (OSHA-2007-0039). OSHA places comments and other 
materials, including any personal information, in the public docket 
without revision, and these materials will be available online at 
http://www.regulations.gov. Therefore, the Agency cautions commenters 
about submitting statements they do not want made available to the 
public, or submitting comments that contain personal information 
(either about themselves or others) such as Social Security numbers, 
birth dates, and medical data.
    5. Docket: To read or download submissions or other material in the 
docket, go to http://www.regulations.gov or the OSHA Docket Office at 
the address above. All documents in the docket are listed in the http://www.regulations.gov index; however, some information (e.g., 
copyrighted material) is not publicly available to read or download 
through the Web site. All submissions, including copyrighted material, 
are available for inspection at the OSHA Docket Office. Contact the 
OSHA Docket Office for assistance in locating docket submissions.
    6. Extension of comment period: Submit requests for an extension of 
the comment period on or before November 15, 2016 to the Office of 
Technical Programs and Coordination Activities, Directorate of 
Technical Support and Emergency Management, Occupational Safety and 
Health Administration, U.S.

[[Page 75443]]

Department of Labor, 200 Constitution Avenue NW., Room N-3655, 
Washington, DC 20210, or by fax to (202) 693-1644.

FOR FURTHER INFORMATION CONTACT: Information regarding this notice is 
available from the following sources:
    Press inquiries: Contact Mr. Frank Meilinger, Director, OSHA Office 
of Communications, U.S. Department of Labor, 200 Constitution Avenue 
NW., Room N-3647, Washington, DC 20210; telephone: (202) 693-1999; 
email: [email protected].
    General and technical information: Contact Mr. Kevin Robinson, 
Director, Office of Technical Programs and Coordination Activities, 
Directorate of Technical Support and Emergency Management, Occupational 
Safety and Health Administration, U.S. Department of Labor, 200 
Constitution Avenue NW., Room N-3655, Washington, DC 20210; phone: 
(202) 693-2110 or email: [email protected].

SUPPLEMENTARY INFORMATION: 

I. Notice of the Application for Expansion

    The Occupational Safety and Health Administration is providing 
notice that Intertek Testing Services NA, Inc. (ITSNA), is applying for 
expansion of its current recognition as an NRTL. ITSNA requests the 
addition of twenty-three (23) test standards to its NRTL scope of 
recognition.
    OSHA recognition of an NRTL signifies that the organization meets 
the requirements specified in 29 CFR 1910.7. Recognition is an 
acknowledgment that the organization can perform independent safety 
testing and certification of the specific products covered within its 
scope of recognition. Each NRTL's scope of recognition includes (1) the 
type of products the NRTL may test, with each type specified by its 
applicable test standard; and (2) the recognized site(s) that has/have 
the technical capability to perform the product-testing and product-
certification activities for test standards within the NRTL's scope. 
Recognition is not a delegation or grant of government authority; 
however, recognition enables employers to use products approved by the 
NRTL to meet OSHA standards that require product testing and 
certification.
    The Agency processes applications by an NRTL for initial 
recognition and for an expansion or renewal of this recognition, 
following requirements in Appendix A to 29 CFR 1910.7. This appendix 
requires that the Agency publish two notices in the Federal Register in 
processing an application. In the first notice, OSHA announces the 
application and provides its preliminary finding. In the second notice, 
the Agency provides its final decision on the application. These 
notices set forth the NRTL's scope of recognition or modifications of 
that scope. OSHA maintains an informational Web page for each NRTL, 
including ITSNA, which details the NRTL's scope of recognition. These 
pages are available from the OSHA Web site at http://www.osha.gov/dts/otpca/nrtl/index.html.
    ITSNA currently has fourteen (14) facilities (sites) recognized by 
OSHA for product testing and certification, with its headquarters 
located at: Intertek Testing Services NA, Inc., 545 East Algonquin 
Road, Suite F, Arlington Heights, Illinois 60005. A complete list of 
ITSNA's scope of recognition is available at https://www.osha.gov/dts/otpca/nrtl/its.html.

II. General Background on the Application

    ITSNA submitted an application, dated April 21, 2015 (OSHA-2007-
0039-0022), to expand its recognition to include twenty-three (23) 
additional test standards. OSHA staff performed detailed analysis of 
the application packet and reviewed other pertinent information. OSHA 
did not perform any on-site reviews in relation to this application.
    Table 1 below lists the appropriate test standards found in ITSNA's 
application for expansion for testing and certification of products 
under the NRTL Program.

  Table 1--Proposed List of Appropriate Test Standards for Inclusion in
                    ITSNA's NRTL Scope of Recognition
------------------------------------------------------------------------
           Test standard                     Test standard title
------------------------------------------------------------------------
UL 5C.............................  Standard for Surface Raceways and
                                     Fittings for Use with Data, Signal
                                     and Control Circuits.
UL 50E............................  Enclosures for Electrical Equipment,
                                     Environmental Considerations.
UL 565............................  Standard for Liquid-Level Gauges for
                                     Anhydrous Ammonia and LP-Gas.
UL 60745-2-1......................  Hand-Held Motor-Operated Electric
                                     Tools--Safety--Part 2-1: Particular
                                     Requirements for Drills and Impact
                                     Drills.
UL 60745-2-14.....................  Hand-Held Motor-Operated Electric
                                     Tools--Safety--Part 2-14:
                                     Particular Requirements for
                                     Planers.
UL 60745-2-17.....................  Hand-Held Motor-Operated Electric
                                     Tools--Safety--Part 2-17:
                                     Particular Requirements for Routers
                                     and Trimmers.
UL 60745-2-3......................  Hand-Held Motor-Operated Electric
                                     Tools--Safety--Part 2-3: Particular
                                     Requirements for Grinders,
                                     Polishers and Disk-Type Sanders.
UL 962A...........................  Standard for Furniture Power
                                     Distribution Units.
UL 1769...........................  Standard for Cylinder Valves.
UL 2061...........................  Standard for Adapters and Cylinder
                                     Connection Devices for Portable LP-
                                     Gas Cylinder Assemblies.
UL 2108...........................  Standard for Low-Voltage Lighting
                                     Systems.
UL 2238...........................  Standard for Cable Assemblies and
                                     Fittings for Industrial Control and
                                     Signal Distribution.
UL 2305...........................  Standard for Display Units,
                                     Fabrication and Installation.
UL 2438...........................  Standard for Outdoor Seasonal-Use
                                     Cord-Connected Wiring Devices.
UL 5085-2.........................  Low Voltage Transformers--Part 2:
                                     General Purpose Transformers.
UL 61010-031......................  Safety-Requirements for Electrical
                                     Equipment for Measurement, Control
                                     and Laboratory Use--Part 031:
                                     Safety requirements for hand-held
                                     probe assemblies for electrical
                                     measurement and test.
UL 61010-2-030....................  Safety requirements for electrical
                                     equipment for measurement, control
                                     and laboratory use--Part 2-030:
                                     Particular requirements for testing
                                     and measuring circuits.
UL 60730-2-2......................  Standard for Automatic Electrical
                                     Controls for Household and Similar
                                     Use; Part 2: Particular
                                     Requirements for Thermal Motor
                                     Protectors.
UL 60745-2-5......................  Hand-Held Motor-Operated Electric
                                     Tools--Safety--Part 2-5: Particular
                                     Requirements for Circular Saws.
UL 60745-2-21.....................  Hand-Held Motor-Operated Electric
                                     Tools--Safety--Part 2-21:
                                     Particular Requirements for Drain
                                     Cleaners.
UL 60950-23.......................  Information Technology Equipment--
                                     Safety--Part 23: Large Data Storage
                                     Equipment.
UL 62368-1........................  Audio/video, information and
                                     communication technology equipment--
                                     Part 1: Safety requirements.

[[Page 75444]]

 
UL 1691...........................  Single Pole Locking-Type Separable
                                     Connectors.
------------------------------------------------------------------------

III. Preliminary Findings on the Application

    ITSNA submitted an acceptable application for expansion of its 
scope of recognition. OSHA's review of the application file, and 
pertinent documentation, indicate that ITSNA can meet the requirements 
prescribed by 29 CFR 1910.7 for expanding its recognition to include 
the addition of these twenty-three test standards for NRTL testing and 
certification listed above. This preliminary finding does not 
constitute an interim or temporary approval of ITSNA's application.
    OSHA welcomes public comment as to whether ITSNA meets the 
requirements of 29 CFR 1910.7 for expansion of its recognition as an 
NRTL. Comments should consist of pertinent written documents and 
exhibits. Commenters needing more time to comment must submit a request 
in writing, stating the reasons for the request. Commenters must submit 
the written request for an extension by the due date for comments. OSHA 
will limit any extension to 10 days unless the requester justifies a 
longer period. OSHA may deny a request for an extension if the request 
is not adequately justified. To obtain or review copies of the exhibits 
identified in this notice, as well as comments submitted to the docket, 
contact the Docket Office, Room N-3653, Occupational Safety and Health 
Administration, U.S. Department of Labor, at the above address. These 
materials also are available online at http://www.regulations.gov under 
Docket No. OSHA-2007-0039
    OSHA staff will review all comments to the docket submitted in a 
timely manner and, after addressing the issues raised by these 
comments, will recommend to the Assistant Secretary for Occupational 
Safety and Health whether to grant ITSNA's application for expansion of 
its scope of recognition. The Assistant Secretary will make the final 
decision on granting the application. In making this decision, the 
Assistant Secretary may undertake other proceedings prescribed in 
Appendix A to 29 CFR 1910.7.
    OSHA will publish a public notice of its final decision in the 
Federal Register.

Authority and Signature

    David Michaels, Ph.D., MPH, Assistant Secretary of Labor for 
Occupational Safety and Health, 200 Constitution Avenue NW., 
Washington, DC 20210, authorized the preparation of this notice. 
Accordingly, the Agency is issuing this notice pursuant to 29 U.S.C. 
657(g)(2), Secretary of Labor's Order No. 1-2012 (77 FR 3912, Jan. 25, 
2012), and 29 CFR 1910.7.

    Signed at Washington, DC, on October 25, 2016.
David Michaels,
Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2016-26203 Filed 10-28-16; 8:45 am]
 BILLING CODE 4510-26-P