[Federal Register Volume 81, Number 170 (Thursday, September 1, 2016)]
[Rules and Regulations]
[Pages 60243-60246]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-20833]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2016-7048; Directorate Identifier 2016-CE-014-AD; 
Amendment 39-18635; AD 2016-18-05]
RIN 2120-AA64


Airworthiness Directives; PILATUS AIRCRAFT LTD. Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for PILATUS 
AIRCRAFT LTD. Models PC-12, PC-12/45, PC-12/47, and PC-12/47E airplanes 
installed with an affected engine mounting frame assembly. This AD 
results from mandatory continuing airworthiness information (MCAI) 
issued by an aviation authority of another country to identify and 
correct an unsafe condition on an aviation product. The MCAI describes 
the unsafe condition as longitudinal material separation on the 
internal surface of the engine mounting frame assembly tubes. We are 
issuing this AD to detect and correct this condition, which could lead 
to partial or complete failure of the structural joint and possibly 
result in in-flight detachment of the engine with consequent loss of 
control.

DATES: This AD is effective October 6, 2016.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in the AD as of October 6, 
2016.

ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
7048; or in person at Document Management Facility, U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.
    For service information identified in this AD, contact Pilatus 
Aircraft Ltd., Customer Support PC-12, CH-6371 Stans, Switzerland; 
phone: +41 41 619 33 33; fax: +41 41 619 73 11; email: 
aircraft.com">SupportPC12@pilatus-aircraft.com; Internet: www.pilatus-aircraft.com. 
For information on the availability of this material at the FAA, call 
(816) 329-4148. It is also available on the Internet at http://www.regulations.gov by searching for Docket No. FAA-2016-7048.

FOR FURTHER INFORMATION CONTACT: Doug Rudolph, Aerospace Engineer, FAA, 
Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 
64106; telephone: (816) 329-4059; fax: (816) 329-4090; email: 
[email protected].

SUPPLEMENTARY INFORMATION: 

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 by adding an AD that would apply to PILATUS AIRCRAFT LTD. 
Models PC-12, PC-12/45, PC-12/47, and PC-12/47E airplanes installed 
with an affected engine mounting frame assembly. The NPRM was published 
in the Federal Register on June 13, 2016 (81 FR 38115). The NPRM 
proposed to correct an unsafe condition for the specified products and 
was based on mandatory continuing airworthiness information (MCAI) 
originated by an aviation authority of another country. The MCAI 
states:

    The PC-12 Engine Mounting Frame Assembly (hereafter referred to 
as ``EMF'' in this AD), Part Number (P/N) 571.20.12.036, is a welded 
structure including three special tubes, P/N 571.20.12.073, P/N 
571.20.12.074 and P/N 571.20.12.107, the ends of which are subject 
to a special swaging process during manufacturing. Longitudinal 
material separation on the internal surface of the special tubes was 
detected on few EMFs on new production aeroplanes. Investigations 
identified the root cause to be an incorrect accomplishment of the 
swaging process.
    This condition, if not detected and corrected, could lead to 
growth of the material separation and subsequent partial or complete 
failure of the structural joint, possibly resulting in in-flight 
detachment of the engine and consequent reduced control, or loss of 
control, of the aeroplane.
    To address this potential unsafe condition, Pilatus issued 
Service Bulletin (SB) No. 71-009, now at Revision 2 (hereafter 
referred to as ``the SB'' in this AD), to provide inspection 
instructions for the affected EMF to detect indications of material 
separation.
    For the reason described above, this AD requires identification 
and inspection of the affected EMF and, depending on the findings, 
their replacement with serviceable EMF.

    The MCAI can be found in the AD docket on the Internet at: https://www.regulations.gov/document?D=FAA-2016-7048-0002.

[[Page 60244]]

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM (81 FR 38115, June 13, 
2016) or on the determination of the cost to the public.

Conclusion

    We reviewed the relevant data and determined that air safety and 
the public interest require adopting the AD as proposed except for 
minor editorial changes. We have determined that these minor changes:
     Are consistent with the intent that was proposed in the 
NPRM (81 FR 38115, June 13, 2016) for correcting the unsafe condition; 
and
     Do not add any additional burden upon the public than was 
already proposed in the NPRM (81 FR 38115, June 13, 2016).

Related Service Information Under 1 CFR Part 51

    We reviewed PILATUS AIRCRAFT LTD. PILATUS PC-12 Service Bulletin 
No: 71-009, Reference No: 345, Modification No: EC-15-0632, Revision 2, 
dated March 18, 2016; Pilatus Powerplant Mounting Frame, Removal/
Installation, Date module/Technical publication 12-A-71-00-05-00A-920A-
A, dated February 26, 2010, found in Pilatus Model type-PC-12, PC-12/
45, PC-12/47 MSN-101-888 Aircraft Maintenance Manual (AMM), Document 
No. 02049, 12-A-AM-00-00-00-I; and Pilatus Powerplant Mounting Frame, 
Removal/Installation, Date module/Technical publication 12-B-71-00-05-
00A-920A-A, dated October 4, 2010, found in Pilatus Model type-PC-12/
47E MSN-1001-UP Aircraft Maintenance Manual (AMM), Document No. 02300, 
12-B-AM-00-00-00-I. The service information describes procedures for 
determining if an affected engine mounting frame assembly (EMF) is 
installed, inspecting the EMF, and replacing the EMF with a serviceable 
EMF. This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section of this 
AD.

Costs of Compliance

    We estimate that this AD will affect 888 products of U.S. registry. 
We also estimate that it would take about 3 work-hours per product to 
comply with the basic requirements of this AD. The average labor rate 
is $85 per work-hour.
    Based on these figures, we estimate the cost of this AD on U.S. 
operators to be $226,440, or $255 per product.
    In addition, we estimate that any necessary follow-on actions would 
cost the following amounts. We have no way of determining the number of 
products that may need these actions.
    The visual and eddy current inspections would take about 3 work-
hours for a cost of $255 per product.
    The replacement of the EMF would take about 90 work-hours and 
require parts costing $33,336, for a cost of $40,986 per product.
    According to the manufacturer, some of the costs of this AD may be 
covered under warranty, thereby reducing the cost impact on affected 
individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all costs in our cost 
estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
7048; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains the NPRM, the regulatory evaluation, any comments received, 
and other information. The street address for the Docket Office 
(telephone (800) 647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

2016-18-05 PILATUS AIRCRAFT LTD.: Amendment 39-18635; Docket No. 
FAA-2016-7048; Directorate Identifier 2016-CE-014-AD.

(a) Effective Date

    This airworthiness directive (AD) becomes effective October 6, 
2016.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to PILATUS AIRCRAFT LTD. Models PC-12, PC-12/45, 
PC-12/47, and PC-12/47E airplanes, all serial numbers, that are:
    (1) Installed with an affected serial number engine mounting 
frame assembly (EMF), part number (P/N) 571.20.12.036, listed in 
figure 1 of paragraph (c)(1) of this AD; and

Figure 1 to Paragraph (c)(1) of this AD: EMF P/N 571.20.12.036, Affected
                             Serial Numbers
------------------------------------------------------------------------
 
-------------------------------------------------------------------------
0001 through 1200 inclusive.
1202 through 1272 inclusive.
1275 through 1323 inclusive.
1325 through 1328 inclusive.

[[Page 60245]]

 
1334 through 1338 inclusive.
1340 and 1342.
1344 through 1346 inclusive.
1348 and 1349.
1358, 1361, and 1365.
------------------------------------------------------------------------

    (2) Certificated in any category.

(d) Subject

    Air Transport Association of America (ATA) Code 71: Power Plant.

(e) Reason

    This AD was prompted by mandatory continuing airworthiness 
information (MCAI) originated by an aviation authority of another 
country to identify and correct an unsafe condition on an aviation 
product. The MCAI describes the unsafe condition as longitudinal 
material separation on the internal surface of the engine mounting 
frame assembly tubes (EMF). We are issuing this AD to detect and 
correct material separation on the internal surface of the engine 
mounting frame assembly tubes, which could lead to partial or 
complete failure of the structural joint and possibly result in in-
flight detachment of the engine with consequent loss of control.

(f) Actions and Compliance

    Do the actions in paragraphs (f)(1) through (7) of this AD. If 
paragraphs (f)(1) through (6) of this AD have already been done 
before October 6, 2016 (the effective date of this AD), then only 
paragraph (f)(7) of this AD applies.
    (1) Within the compliance time identified in figure 2 of 
paragraph (f)(1) of this AD, do an ultrasonic inspection of the 
swaged engine mounting tube ends of the affected EMF following the 
instructions of paragraph 3.B.(1) of PILATUS AIRCRAFT LTD PILATUS 
PC-12 Service Bulletin No: 71-009, Reference No: 345, Modification 
No: EC-15-0632, Revision 2, dated March 18, 2016.

    Figure 2 to Paragraph (f)(1) of This AD: Initial Compliance Time
------------------------------------------------------------------------
 
------------------------------------------------------------------------
                     A or B, Whichever Occurs Later
------------------------------------------------------------------------
A......................................  Before the EMF exceeds 11,000
                                          hours time-in-service (TIS) or
                                          13,500 flight cycles (FC),
                                          whichever occurs first since
                                          first installation of the EMF
                                          on an airplane.
B......................................  Within 1,000 hours TIS or 1,000
                                          FC or 6 months, whichever
                                          occurs first after October 6,
                                          2016 (the effective date of
                                          this AD).
------------------------------------------------------------------------

    (2) If an indication with an echo of less than 40 percent full 
screen height is detected on an EMF during the ultrasonic inspection 
required in paragraph (f)(1) of this AD, except for paragraph 
(f)(7), no further actions are required for this AD. Document 
compliance with this AD in the maintenance records.
    (3) If an indication with an echo of 40 percent full screen 
height or more is detected on an EMF during the ultrasonic 
inspection required in paragraph (f)(1) of this AD, do the actions 
in paragraphs (f)(3)(i) through (iii) of this AD, as applicable.
    (i) Before further flight and repetitively thereafter at 
intervals not to exceed 600 hours TIS or 12 months, whichever occurs 
first, do a visual inspection of the welding and do an eddy current 
inspection of the tubes at the indication point detected during the 
ultrasonic inspection. Use the instructions of paragraphs 3.B.(2) 
and 3.B.(3) of PILATUS AIRCRAFT LTD PILATUS PC-12 Service Bulletin 
No: 71-009, Reference No: 345, Modification No: EC-15-0632, Revision 
2, dated March 18, 2016.
    (ii) If any cracks are found during any of the visual 
inspections or if an indication with a signal of 20 percent or more 
is detected during any of the eddy current inspections required in 
paragraph (f)(3)(i) of this AD, before further flight, replace the 
EMF with a serviceable EMF following the instructions in the service 
information listed in paragraph (f)(5) of this AD, including all 
subparagraphs as applicable.
    (iii) Unless already done as required by paragraph (f)(3)(ii) of 
this AD, with>in 1,800 hours TIS or 36 months after the initial 
visual and eddy current inspections of the affected EMF required by 
paragraph (f)(3)(i) of this AD, whichever occurs first, replace the 
EMF with a serviceable EMF following the instructions in the service 
information listed in paragraph (f)(5) of this AD, including all 
subparagraphs as applicable.
    (4) For the purpose of this AD, a serviceable EMF is defined as 
any EMF that is not listed in figure 1 of paragraph (c)(1) of this 
AD or an affected EMF that is listed in figure 1 of paragraph (c)(1) 
of this AD but has had the ultrasonic inspection required in 
paragraph (f)(1) of this AD and had an indication with an echo of 
less than 40 percent full screen height.
    (5) For replacement of the EMF, follow the instructions listed 
in paragraphs (f)(5)(i) and (ii), as applicable.
    (i) For Models PC-12, PC-12/45, and PC-12/47, manufacturer 
serial numbers (MSN) 101-888: Pilatus Powerplant Mounting Frame, 
Removal/Installation, Date module/Technical publication 12-A-71-00-
05-00A-920A-A, dated February 26, 2010, found in Pilatus Model type-
PC-12, PC-12/45, PC-12/47 MSN-101-888 Aircraft Maintenance Manual 
(AMM), Document No. 02049, 12-A-AM-00-00-00-I.
    (ii) For Model PC-12/47E, MSN 1001 and up: Pilatus Powerplant 
Mounting Frame, Removal/Installation, Date module/Technical 
publication 12-B-71-00-05-00A-920A-A, dated October 4, 2010, found 
in Pilatus Model type-PC-12/47E MSN-1001-UP Aircraft Maintenance 
Manual (AMM), Document No. 02300, 12-B-AM-00-00-00-I.
    (6) If an EMF has an indication with an echo of 40 percent or 
more during the ultrasonic inspection required in paragraph (f)(1) 
of this AD, you may replace the EMF with a serviceable EMF in lieu 
of the visual or eddy current inspections required in paragraph 
(f)(3)(i) of this AD. For replacement of the EMF, follow the 
instructions in the service information listed in paragraph (f)(5) 
of this AD, including all subparagraphs as applicable.
    (7) As of October 6, 2016 (the effective date of this AD), do 
not install an EMF P/N 571.20.12.036 unless it has been determined 
to be a serviceable EMF as specified in paragraph (f)(4) of this AD.
    (8) Airplanes with an MSN of 1556 or higher are not affected by 
this AD provided that the EMF has not been replaced since its 
manufacture. A review of the maintenance records, Airworthiness 
Approval Tag (FAA Form 8130-3), or other positive form of parts 
identification such as a shipping ticket, invoice, or direct ship 
authority letter, can be used to determine the serial number of the 
EMF.

(g) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Standards Office, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. Send 
information to ATTN: Doug Rudolph, Aerospace Engineer, FAA, Small 
Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 
64106; telephone: (816) 329-4059; fax: (816) 329-4090; email: 
[email protected]. Before using any approved AMOC on any airplane 
to which the AMOC applies, notify your appropriate principal 
inspector (PI) in the FAA Flight Standards District Office (FSDO), 
or lacking a PI, your local FSDO.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

(h) Related Information

    (1) Refer to MCAI European Aviation Safety Agency (EASA) AD No. 
2016-0081, dated April 25, 2016, for related information pertaining 
to this AD. The MCAI can be found in the AD docket on the Internet 
at: https://www.regulations.gov/document?D=FAA-2016-7048-0002.

(i) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) PILATUS PC-12 Service Bulletin No: 71-009, Reference No: 
345, Modification No: EC-15-0632, Revision 2, dated March 18, 2016;
    (ii) Pilatus Powerplant Mounting Frame, Removal/Installation, 
Date module/Technical publication 12-A-71-00-05-00A-920A-A, dated 
February 26, 2010, found in Pilatus Model type-PC-12, PC-12/45, PC-
12/47 MSN-101-888 Aircraft Maintenance Manual

[[Page 60246]]

(AMM), Document No. 02049, 12-A-AM-00-00-00-I; and
    (iii) Pilatus Powerplant Mounting Frame, Removal/Installation, 
Date module/Technical publication 12-B-71-00-05-00A-920A-A, dated 
October 4, 2010, found in Pilatus Model type- PC-12/47E MSN-1001-UP 
Aircraft Maintenance Manual (AMM), Document No. 02300, 12-B-AM-00-
00-00-I.
    (3) For service information identified in this AD, contact 
Pilatus Aircraft Ltd., Customer Support PC-12, CH-6371 Stans, 
Switzerland; phone: +41 41 619 33 33; fax: +41 41 619 73 11; email: 
aircraft.com">SupportPC12@pilatus-aircraft.com; Internet: www.pilatus-
aircraft.com.
    (4) You may view this service information at the FAA, Small 
Airplane Directorate, 901 Locust, Kansas City, Missouri 64106. For 
information on the availability of this material at the FAA, call 
(816) 329-4148. In addition, you can access this service information 
on the Internet at http://www.regulations.gov by searching for and 
locating Docket No. FAA-2016-7048.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Kansas City, Missouri, on August 23, 2016.
David R. Showers,
Acting Manager, Small Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2016-20833 Filed 8-31-16; 8:45 am]
 BILLING CODE 4910-13-P