[Federal Register Volume 81, Number 65 (Tuesday, April 5, 2016)]
[Proposed Rules]
[Pages 19514-19516]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-07578]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2016-5041; Directorate Identifier 2015-NM-102-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain The Boeing Company Model 747-8 and 747-8F series airplanes. 
This proposed AD was prompted by a report that static strength analysis 
has shown that the aluminum transmission aft bearing plate assemblies 
have inadequate structural strength for one or more of the required 
load cases, including cases for drive system jam, flap skew, and 
structural damage tolerance. Inadequate structural strength can result 
in damage to the transmission aft bearing plate assemblies. This 
proposed AD would require removing aluminum transmission aft bearing 
plate assemblies from the flap track and installing titanium 
transmission aft bearing plate assemblies to the flap track. We are 
proposing this AD to prevent inadequate structural strength of 
transmission aft bearing plate assemblies. This condition could result 
in damaged transmission aft bearing plate assemblies, which could 
result in incorrect operation and departure of the flap from the 
airplane and consequent loss of controllability of the airplane.

DATES: We must receive comments on this proposed AD by May 20, 2016.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Boeing 
Commercial Airplanes, Attention: Data & Services Management, P.O. Box 
3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-5000, 
extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. 
You may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221. It 
is also available on the Internet at http://www.regulations.gov by 
searching for and locating Docket No. FAA-2016-5041.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-

[[Page 19515]]

5041; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Bill Ashforth, Aerospace Engineer, 
Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office 
(ACO), 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-
6432; fax: 425-917-6590; email: [email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2016-5041; 
Directorate Identifier 2015-NM-102-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    We have received a report that static strength analysis has shown 
that the aluminum transmission aft bearing plate assemblies have 
inadequate structural strength for one or more of the required load 
cases, including cases for drive system jam, flap skew, and structural 
damage tolerance. These types of load cases can cause a flap 
transmission torque brake to engage, which will then cause additional 
loading on the transmission aft bearing plate assemblies common to that 
flap. This could cause damage to the transmission aft bearing plate 
assemblies. This condition, if not corrected, could result in 
transmission aft bearing plate assemblies working incorrectly or 
departure of the flap from the airplane, which could result in loss of 
controllability of the airplane.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Alert Service Bulletin 747-57A2348, dated June 
12, 2015. The service information describes procedures for removing the 
aluminum transmission aft bearing plate assembly from the flap track 
and installing a new titanium transmission aft bearing plate assembly 
to the flap track. This service information is reasonably available 
because the interested parties have access to it through their normal 
course of business or by the means identified in the ADDRESSES section.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in the service information described previously.

Costs of Compliance

    We estimate that this proposed AD affects 11 airplanes of U.S. 
registry.
    We estimate the following costs to comply with this proposed AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
                Action                         Labor cost           Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Replacement...........................  114 work-hours x $85 per         $48,682         $58,372        $642,092
                                         hour = $9,690.
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, all of the costs of this proposed AD 
may be covered under warranty, thereby reducing the cost impact on 
affected individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all costs in our cost 
estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

[[Page 19516]]

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

The Boeing Company: Docket No. FAA-2016-5041; Directorate Identifier 
2015-NM-102-AD.

(a) Comments Due Date

    We must receive comments by May 20, 2016.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 747-8 and 747-8F 
series airplanes, certified in any category, as identified in Boeing 
Alert Service Bulletin 747-57A2348, dated June 12, 2015.

(d) Subject

    Air Transport Association (ATA) of America Code 57, Wings.

(e) Unsafe Condition

    This AD was prompted by a report that static strength analysis 
has shown that the aluminum transmission aft bearing plate 
assemblies have inadequate structural strength for one or more of 
the required load cases, including cases for drive system jam, flap 
skew, and structural damage tolerance. Inadequate structural 
strength can result in damage to the transmission aft bearing plate 
assemblies. We are issuing this AD to prevent inadequate structural 
strength of transmission aft bearing plate assemblies. This 
condition could result in damaged transmission aft bearing plate 
assemblies, which could result in incorrect operation and departure 
of the flap from the airplane and consequent loss of controllability 
of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Replacement

    Within 48 months after the effective date of this AD: Remove 
aluminum transmission aft bearing plate assemblies from the flap 
track and install new titanium transmission aft bearing plate 
assemblies to the flap track, in accordance with the Accomplishment 
Instructions of Boeing Alert Service Bulletin 747-57A2348, dated 
June 12, 2015.

(h) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or local 
Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in paragraph (i)(1) of this AD. 
Information may be emailed to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Seattle ACO, to make those findings. To be approved, the 
repair method, modification deviation, or alteration deviation must 
meet the certification basis of the airplane, and the approval must 
specifically refer to this AD.
    (4) For service information that contains steps that are labeled 
as Required for Compliance (RC), the provisions of paragraphs 
(h)(4)(i) and (h)(4)(ii) of this AD apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. An AMOC is required for any deviations to RC steps, 
including substeps and identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(i) Related Information

    (1) For more information about this AD, contact Bill Ashforth, 
Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle ACO, 
1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6432; 
fax: 425-917-6590; email: [email protected].
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. For information on the availability of this 
material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on March 24, 2016.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2016-07578 Filed 4-4-16; 8:45 am]
BILLING CODE 4910-13-P