[Federal Register Volume 81, Number 65 (Tuesday, April 5, 2016)]
[Proposed Rules]
[Pages 19505-19509]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-07569]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2016-5039; Directorate Identifier 2013-NM-148-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to supersede airworthiness directive (AD) 2000-10-
18, that applies to certain Airbus Model A300 series airplanes; Model 
A300 B4-600, B4-600R, F4-600R series airplanes, and Model A300 C4-605R 
Variant F airplanes (collectively called Model A300-600 series 
airplanes); and Model A310 series airplanes. AD 2000-10-18 requires 
repetitive inspections to detect cracks in the lower spar of the engine 
pylons between ribs 6 and 7, and repair if necessary. Since we issued 
AD 2000-10-18, we have determined that the compliance times for the 
initial inspection and the repetitive intervals must be reduced to 
allow timely detection of cracks in the engine pylon's lower spar 
between ribs 6 and 7. This proposed AD would reduce the compliance 
times for the initial inspection and the repetitive intervals. We are 
proposing this AD to prevent fatigue cracking, which could result in 
reduced structural integrity of the engine pylon's lower spar, and 
possible separation of the engine from the airplane.

DATES: We must receive comments on this proposed AD by May 20, 2016.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this NPRM, contact Airbus 
SAS, Airworthiness Office--EAW, 1 Rond Point Maurice Bellonte, 31707 
Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 44 
51; email [email protected]; Internet http://www.airbus.com. You may view this referenced service information at the 
FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. 
For information on the availability of this material at the FAA, call 
425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
5039; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Operations office (telephone 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone (425) 227-2125; 
fax (425) 227-1149.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2016-5039; 
Directorate Identifier 2013-NM-148-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://

[[Page 19506]]

www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    On May 16, 2000, we issued AD 2000-10-18, Amendment 39-11742 (65 FR 
34055, May 26, 2000). AD 2000-10-18 requires actions intended to 
address an unsafe condition on certain Airbus Model A300 series 
airplanes; Model A300 B4-600, B4-600R, F4-600R series airplanes, and 
Model A300 C4-605R Variant F airplanes (collectively called Model A300-
600 series airplanes); and Model A310 series airplanes.
    Since we issued AD 2000-10-18, Amendment 39-11742 (65 FR 34055, May 
26, 2000), we have determined that the compliance times for the initial 
inspection and the repetitive intervals must be reduced to allow timely 
detection of cracks in the engine pylon's lower spar between ribs 6 and 
7.
    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued EASA 
Airworthiness Directive 2013-0167, dated July 26, 2013 (referred to 
after this as the Mandatory Continuing Airworthiness Information, or 
``the MCAI''), to correct an unsafe condition. The MCAI states:

    Cracks were found between ribs 6 and 7 in the lower spar of 
engine pylons on A310, A300 and A300-600 aeroplanes. To prevent 
crack initiation, a first inspection programme of this area was 
rendered mandatory by DGAC [Direction G[eacute]n[eacute]rale de 
l'Aviation Civile] France AD 93-228-154 (later revised, currently at 
Revision 3) [http://ad.easa.europa.eu/blob/19932283tb__Superseded.pdf/AD_F-1993-228-154R3_1] [which corresponds 
to certain actions in in FAA AD 2000-10-18, Amendment 39-11742 (65 
FR 34055)] for A300 and A300-600 aeroplanes.
    At a later date and due to new findings, a specific inspection 
programme for A310 aeroplanes was rendered mandatory by DGAC France 
AD 1999-239-287(B) [which corresponds to certain other actions in 
FAA AD 2000-10-18, Amendment 39-11742 (65 FR 34055, May 26, 2000)]. 
That [French] AD was later superseded by EASA AD 2008-0001 [http://ad.easa.europa.eu/blob/easa_ad_2008_0001_Superseded.pdf/AD_2008-0001_1], which introduced new thresholds and intervals in the frame 
of the A310 extended service goal (ESG) exercise.
    Since DGAC France AD 1993-228-154(B)R3 and EASA AD 2008-0001 
were issued, a fleet survey and updated Fatigue and Damage Tolerance 
analyses have been performed in order to substantiate the second ESG 
for A300-600, called ESG2 exercise. The results of these analyses 
have shown that the inspection threshold and interval must be 
reduced to allow timely detection of cracks in the engine pylon 
lower spar between ribs 6 and 7.
    For the reasons described above, this new [EASA] AD retains the 
requirements of DGAC France AD 1993-228-154(B)R3 and EASA AD 2008-
0001, which are superseded, and requires accomplishment of the [eddy 
current or liquid penetrant] inspections [for cracking] and, 
depending on findings, [related investigative and] corrective 
actions [repairs], within the new thresholds and intervals specified 
in Airbus Service Bulletin (SB) A300-54-0073 Revision 03 [dated 
October 11, 2012] or SB A310-54-2017 Revision 06 [dated October 3, 
2012] or SB A300-54-6014 Revision 07 [dated September 5, 2012].

    Related investigative actions include eddy current or liquid 
penetrant inspections for cracking of areas with removed protection. 
The unsafe condition is cracking in the lower spar of the engine pylons 
between ribs 6 and 7, which could result in reduced structural 
integrity of the engine pylon's lower spar, and possible separation of 
the engine from the airplane. You may examine the MCAI in the AD docket 
on the Internet at http://www.regulations.gov by searching for and 
locating it in Docket No. FAA-2016-5039.
    The compliance times for the inspections vary, depending on 
airplane configuration and utilization as follows.
    For Model A300-600 series airplanes:
     The compliance time for the initial inspection is before 
the accumulation of 10,900 total flight cycles.
     The compliance times for the repetitive inspection 
interval are 5,700 flight cycles for pre-doubler modified airplanes; 
and for post-doubler modified airplanes, the compliance times range 
from 7,200 flight cycles or 8,200 flight hours, to 8,400 flight cycles 
or 16,000 flight hours.
     The compliance times for the initial inspection following 
crack repair range from 5,200 flight cycles or 5,900 flight hours, to 
6,600 flight cycles or 13,400 flight hours; and the compliance times 
for the post-repair repetitive inspection range from 2,200 flight 
cycles or 2,500 flight hours, to 3,400 flight cycles or 6,900 flight 
hours.
    For Model A300 series airplanes:
     The compliance times for the initial inspection range from 
before the accumulation of 4,400 total flight cycles to 9,400 total 
flight cycles.
     The compliance times for the repetitive inspection 
interval range from 4,400 flight cycles to 6,100 flight cycles.
     The initial inspection compliance times for post-doubler 
modified airplanes range from 12,700 flight cycles or 25,700 flight 
hours, to 20,700 flight cycles or 30,900 flight hours after the 
modification; the post-doubler repetitive inspection interval ranges 
from 7,800 flight cycles or 16,600 flight hours, to 12,200 flight 
cycles or 18,200 flight hours.
     The compliance times for the initial post-repair 
inspection range from 6,500 flight cycles or 13,900 flight hours, to 
10,200 flight cycles or 15,200 flight hours; and the post-repair 
repetitive inspection interval ranges from 4,700 flight cycles or 
10,000 flight hours, to 11,000 flight cycles or 23,300 flight hours.
    For Model A310 series airplanes:
     The compliance times for the initial inspection range from 
before the accumulation of 3,000 total flight cycles or 14,900 total 
flight hours, to 6,400 total flight cycles or 12,800 total flight 
cycles.
     The compliance times for the repetitive inspection 
interval range from 4,600 flight cycles or 23,800 flight hours, to 
6,200 flight cycles or 12,400 flight hours.
     The initial inspection compliance times for post-doubler 
modified airplanes range from 7,500 flight cycles or 37,200 flight 
hours, to 11,000 flight cycles or 22,000 flight hours after the 
modification; the post-doubler repetitive inspection interval ranges 
from 5,900 flight cycles or 29,500 flight hours, to 6,500 flight cycles 
or 13,000 flight hours.
     The compliance times for the initial post-repair 
inspection range from 4,500 flight cycles or 23,700 flight hours, to 
5,400 flight cycles or 10,800 flight hours; and the post-repair 
repetitive inspection interval ranges from 2,500 flight cycles or 
12,200 flight hours, to 2,800 flight cycles or 5,600 flight hours.

Related Service Information Under 1 CFR part 51

    Airbus has issued the following service bulletins.
     Airbus Service Bulletin A300-54-0073, Revision 03, dated 
October 11, 2012 (for Model A300 series airplanes).
     Airbus Service Bulletin A300-54-6014, Revision 07, dated 
September 5, 2012 (for Model A300-600 series airplanes).
     Airbus Service Bulletin A310-54-2017, Revision 06, dated 
October 3, 2012 (for Model A310 series airplanes).
    This service information describes procedures for inspecting for 
cracking of the engine pylon's lower spar between ribs 6 and 7 and 
related investigative actions. This service information is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in the 
ADDRESSES section.

[[Page 19507]]

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Differences Between This Proposed AD and the MCAI or Service 
Information

    Unlike the procedures described in the following service 
information, this proposed AD would not permit further flight if cracks 
are detected in the lower spar of the engine pylons between ribs 6 and 
7. We have determined that, because of the safety implications and 
consequences associated with that cracking, any cracked lower spar of 
the engine pylons between ribs 6 and 7 must be repaired or modified 
before further flight. This difference has been coordinated with the 
EASA.
     Airbus Service Bulletin A300-54-0073, Revision 03, dated 
October 11, 2012 (for Model A300 series airplanes).
     Airbus Service Bulletin A300-54-6014, Revision 07, dated 
September 5, 2012 (for Model A300-600 series airplanes).
     Airbus Service Bulletin A310-54-2017, Revision 06, dated 
October 3, 2012 (for Model A310 series airplanes).
    Where the ``Grace periods'' specified in paragraph 1.E., 
``Compliance,'' of the service information identified previously 
contain ambiguous language, i.e., ``for aircraft that have already 
exceeded or are close to exceed the threshold or scheduled interval,'' 
this proposed AD does not include that language. We have clarified this 
exception to the service information in paragraph (i)(2) of this 
proposed AD.

Costs of Compliance

    We estimate that this proposed AD affects 156 airplanes of U.S. 
registry.
    We also estimate that it would take about 6 work-hours per product 
to comply with the basic requirements of this proposed AD. The average 
labor rate is $85 per work hour. Based on these figures, we estimate 
the cost of this proposed AD on U.S. operators to be $79,560, or $510 
per product.
    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition actions specified in this proposed 
AD. We have no way of determining the number of aircraft that might 
need these actions.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Airworthiness Directive (AD) 
2000-10-18, Amendment 39-11742 (65 FR 34055, May 26, 2000), and adding 
the following new AD:

Airbus: Docket No. FAA-2016-5039; Directorate Identifier 2013-NM-
148-AD.

(a) Comments Due Date

    We must receive comments by May 20, 2016.

(b) Affected ADs

    This AD replaces AD 2000-10-18, Amendment 39-11742 (65 FR 34055, 
May 26, 2000).

(c) Applicability

    This AD applies to the Airbus airplanes identified in paragraphs 
(c)(1) through (c)(6) of this AD, certificated in any category, 
except airplanes on which Airbus Modification 10149 has been 
incorporated in production.
    (1) Airbus Model A300 B2-1A, B2-1C, B2K-3C, B2-203, B4-2C, B4-
103, and B4-203 airplanes.
    (2) Airbus Model A300 B4-601, B4-603, B4-620, and B4-622 
airplanes.
    (3) Airbus Model A300 B4-605R and B4-622R airplanes.
    (4) Airbus Model A300 F4-605R and F4-622R airplanes.
    (5) Airbus Model A300 C4-605R Variant F airplanes.
    (6) Airbus Model A310-203, -204, -221, -222, -304, -322, -324, 
and -325 airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 54, Nacelles/
pylons.

(e) Reason

    This AD was prompted by a determination that the inspection 
compliance time and repetitive interval must be reduced to allow 
timely detection of cracks in the engine pylon's lower spar between 
ribs 6 and 7. We are issuing this AD to prevent fatigue cracking, 
which could result in reduced structural integrity of the engine 
pylon's lower spar, and possible separation of the engine from the 
airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspections and Corrective Actions

    Except as provided by paragraphs (i)(1) and (i)(2) of this AD, 
at the applicable time specified in paragraph 1.E., ``Compliance,'' 
of the applicable Airbus service bulletin specified in paragraphs 
(g)(1), (g)(2), and (g)(3) of this AD: Do an eddy current or liquid 
penetrant inspection for cracking of the

[[Page 19508]]

engine pylon's lower spar between ribs 6 and 7; and do all 
applicable related investigative and corrective actions; in 
accordance with the Accomplishment Instructions of the applicable 
Airbus service bulletin specified in paragraphs (g)(1), (g)(2), and 
(g)(3) of this AD, except as required by paragraph (i)(3) of this 
AD. Do all applicable related investigative and corrective actions 
before further flight. Repeat the inspection of the engine pylon's 
lower spar between ribs 6 and 7 thereafter at the applicable time 
and intervals specified in paragraph 1.E., ``Compliance,'' of the 
applicable Airbus service bulletin specified in paragraphs (g)(1), 
(g)(2), and (g)(3) of this AD until a repair or modification 
specified in the Accomplishment Instructions of the applicable 
Airbus service bulletin identified in paragraphs (g)(1), (g)(2), and 
(g)(3) of this AD is done.

    Note 1 to paragraph (g) of this AD: An additional source of 
guidance for accomplishing the modification specified in Airbus 
Service Bulletin A300-54-0073, Revision 03, dated October 11, 2012, 
can be found in Airbus Service Bulletin A300-54-0080, Revision 02, 
dated July 9, 2002.


    Note 2 to paragraph (g) of this AD: An additional source of 
guidance for accomplishing the modification specified in Airbus 
Service Bulletin A300-54-6014, Revision 07, dated September 5, 2012, 
can be found in Airbus Service Bulletin A300-54-6020, Revision 02, 
dated July 9, 2002.


    Note 3 to paragraph (g) of this AD: An additional source of 
guidance for accomplishing the modification specified in Airbus 
Service Bulletin A310-54-2017, Revision 06, dated October 3, 2012, 
can be found in Airbus Service Bulletin A310-54-2023, Revision 03, 
dated July 9, 2002.

    (1) Airbus Service Bulletin A300-54-0073, Revision 03, dated 
October 11, 2012 (for Model A300 series airplanes).
    (2) Airbus Service Bulletin A300-54-6014, Revision 07, dated 
September 5, 2012 (for Model A300-600 series airplanes).
    (3) Airbus Service Bulletin A310-54-2017, Revision 06, dated 
October 3, 2012 (for Model A310 series airplanes).

(h) Post-Repair/Modification and Corrective Actions

    For airplanes on which any repair or modification specified in 
the Accomplishment Instructions of the applicable Airbus service 
bulletin identified in paragraphs (g)(1), (g)(2), and (g)(3) of this 
AD is done: Except as provided by paragraphs (i)(1) and (i)(2) of 
this AD, at the applicable time specified in paragraph 1.E., 
``Compliance,'' of the applicable Airbus service bulletin specified 
in paragraphs (g)(1), (g)(2), and (g)(3) of this AD: Do an eddy 
current or liquid penetrant inspection for cracking of the engine 
pylon's lower spar between ribs 6 and 7; and do all applicable 
related investigative and corrective actions; in accordance with the 
Accomplishment Instructions of the applicable Airbus service 
bulletin specified in paragraphs (g)(1), (g)(2), and (g)(3) of this 
AD, except as required by paragraph (i)(3) of this AD. Do all 
applicable related investigative and corrective actions before 
further flight. Repeat the inspection of the engine pylon's lower 
spar between ribs 6 and 7 thereafter at the applicable time and 
intervals specified in paragraph 1.E., ``Compliance,'' of the 
applicable Airbus service bulletin specified in paragraphs (g)(1), 
(g)(2), and (g)(3) of this AD.

(i) Exceptions to Service Information

    (1) Where a ``Threshold'' is specified in paragraph 1.E., 
``Compliance,'' of the service information specified in paragraphs 
(g)(1), (g)(2), and (g)(3) of this AD, the ``FC'' and ``FH'' 
compliance times are total flight cycle and total flight hour 
compliance times, except that if a repair or service bulletin 
identified in paragraph 1.E., ``Compliance,'' of the service 
bulletins specified in paragraphs (g)(1), (g)(2), and (g)(3) of this 
AD has been done, the ``FC'' and ``FH'' compliance times are flight 
cycle and flight hour compliance times since the identified repair 
or service bulletin was done.
    (2) Except as provided by paragraphs (i)(2)(i) and (i)(2)(ii) of 
this AD: For the ``Grace period'' specified in paragraph 1.E., 
``Compliance,'' of the service information specified in paragraphs 
(g)(1), (g)(2), and (g)(3) of this AD, operators must comply with 
the actions specified in paragraphs (g) and (h) of this AD, as 
applicable, at the later of the applicable times in the 
``Threshold'' and ``Grace Period'' specified in paragraph 1.E., 
``Compliance,'' of the service information, except the language 
``for aircraft that have already exceeded or are close to exceed the 
threshold or scheduled interval'' does not apply.
    (i) Where Airbus Service Bulletin A300-54-0073, Revision 03, 
dated October 11, 2012; and Airbus Service Bulletin A310-54-2017, 
Revision 06, dated October 3, 2012; specify a compliance time ``. . 
. after receipt of this Inspection Service Bulletin without 
exceeding the requirements of previous issue of this ISB,'' this AD 
requires compliance within the specified compliance time after the 
effective date of this AD.
    (ii) Where Airbus Service Bulletin A300-54-6014, Revision 07, 
dated September 5, 2012, specifies a compliance time ``. . . after 
receipt of this Inspection Service Bulletin without exceeding the 
requirements of previous issue of this SB,'' this AD requires 
compliance within the specified compliance time after the effective 
date of this AD.
    (3) If any crack is found during any inspection required by this 
AD and an Airbus service bulletin specified in paragraph (g)(1), 
(g)(2), or (g)(3) of this AD specifies to contact Airbus: Before 
further flight, repair the crack using a method approved by the 
Manager, International Branch, ANM-116, Transport Airplane 
Directorate, FAA; or the European Aviation Safety Agency (EASA); or 
Airbus's EASA Design Organization Approval (DOA).

(j) Credit for Previous Actions

    This paragraph provides credit for actions required by 
paragraphs (g) and (h) of this AD, if those actions were performed 
before the effective date of this AD using an applicable service 
bulletin specified in paragraphs (j)(1) through (j)(10) of this AD.
    (1) Airbus Service Bulletin A300-54-0073, Revision 1, dated 
March 28, 1994 (for Model A300 series airplanes), which is 
incorporated by reference in AD 96-11-05, Amendment 39-9630 (61 FR 
26091, May 24, 1996).
    (2) Airbus Service Bulletin A300-54-0073, Revision 02, dated 
July 9, 2002 (for Model A300 series airplanes), which is not 
incorporated by reference in this AD.
    (3) Airbus Service Bulletin A300-54-6014, Revision 1, dated 
March 28, 1994 (for Model A300-600 series airplanes), which is 
incorporated by reference in AD 96-11-05, Amendment 39-9630 (61 FR 
26091, May 24, 1996).
    (4) Airbus Service Bulletin A300-54-6014, Revision 03, dated 
June 4, 1998 (for Model A300-600 series airplanes), which is not 
incorporated by reference in this AD.
    (5) Airbus Service Bulletin A300-54-6014, Revision 04, dated 
March 9, 2002 (for Model A300-600 series airplanes), which is not 
incorporated by reference in this AD.
    (6) Airbus Service Bulletin A300-54-6014, Revision 05, dated 
September 1, 2011 (for Model A300-600 series airplanes), which is 
not incorporated by reference in this AD.
    (7) Airbus Service Bulletin A300-54-6014, Revision 06, dated May 
24, 2012 (for Model A300-600 series airplanes), which is not 
incorporated by reference in this AD.
    (8) Airbus Service Bulletin A310-54-2017, Revision 03, dated 
June 11, 1999 (for Model A310 series airplanes), which is 
incorporated by reference in AD 2000-10-18, Amendment 39-11742 (65 
FR 34055, May 26, 2000).
    (9) Airbus Service Bulletin A310-54-2017, Revision 04, dated 
July 9, 2002 (for Model A310 series airplanes), which is not 
incorporated by reference in this AD.
    (10) Airbus Service Bulletin A310-54-2017, Revision 05, dated 
November 16, 2007 (for Model A310 series airplanes), which is not 
incorporated by reference in this AD.

(k) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Branch, send it to ATTN: Dan Rodina, 
Aerospace Engineer, International Branch, ANM-116, Transport 
Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057-
3356; telephone (425) 227-2125; fax (425) 227-1149. Information may 
be emailed to: [email protected]. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office. The 
AMOC approval letter must specifically reference this AD.
    (2) Contacting the Manufacturer: As of the effective date of 
this AD, for any requirement in this AD to obtain corrective actions 
from a manufacturer, the action must be accomplished using a method 
approved by

[[Page 19509]]

the Manager, International Branch, ANM-116, Transport Airplane 
Directorate, FAA; or the EASA; or Airbus's EASA DOA. If approved by 
the DOA, the approval must include the DOA-authorized signature.

(l) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) EASA Airworthiness Directive 2013-0167, dated July 26, 2013, 
for related information. This MCAI may be found in the AD docket on 
the Internet at http://www.regulations.gov by searching for and 
locating it in Docket No. FAA-2016-5039.
    (2) For service information identified in this AD, contact 
Airbus SAS, Airworthiness Office--EAW, 1 Rond Point Maurice 
Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; 
fax +33 5 61 93 44 51; email [email protected]; 
Internet http://www.airbus.com. You may view this service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on March 24, 2016.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2016-07569 Filed 4-4-16; 8:45 am]
 BILLING CODE 4910-13-P