[Federal Register Volume 81, Number 62 (Thursday, March 31, 2016)]
[Rules and Regulations]
[Pages 18464-18467]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-07025]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2016-5033; Directorate Identifier 2015-NM-118-AD; 
Amendment 39-18450; AD 2016-07-05]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain 
The Boeing Company Model 747-8 series airplanes. This AD requires an 
inspection to determine if all oxygen components in the passenger 
oxygen system are installed, installation of new o-rings, and 
corrective actions if necessary. This AD was prompted by a report that 
oxygen tube couplings in the passenger oxygen system could be missing 
or incorrectly installed. We are issuing this AD to detect and correct 
oxygen leaks from oxygen tube couplings in the passenger oxygen system, 
which could result in depletion of emergency oxygen at a faster rate 
than expected, reduce the passengers' and crews' protection from 
hypoxia at elevated cabin altitudes, and increase the risk of a fire.

DATES: This AD is effective April 15, 2016.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of April 15, 
2016.
    We must receive comments on this AD by May 16, 2016.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For service information identified in this final rule, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may view this referenced service information 
at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., 
Renton, WA. For information on the availability of this material at the 
FAA, call 425-227-1221. It is also available on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
5033.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
5033; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this AD, the regulatory evaluation, any comments received, and 
other information. The street address for the Docket Office (phone: 
800-647-5527) is in the ADDRESSES section. Comments will be available 
in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Susan Monroe, Aerospace Engineer, 
Cabin Safety and Environmental Systems Branch, ANM-150S, FAA, Seattle 
Aircraft Certification Office (ACO), 1601 Lind Avenue SW., Renton, WA; 
phone: 425-917-6457; fax: 425-917-6590; email: [email protected].

SUPPLEMENTARY INFORMATION: 

Discussion

    We have determined that some Model 747-8 series airplanes could 
have oxygen components missing or incorrectly installed at oxygen tube 
couplings attached to the outboard stowage bin support assemblies. The 
manufacturer believes that these airplanes were delivered with the 
correct configuration of oxygen components. However, because of an 
error in an engineering drawing and related parts list, which omitted 
part number call-outs for some oxygen components, we want to be certain

[[Page 18465]]

installations are correct and prevent incorrect installation during 
subsequent rework of the oxygen tubing components. This condition, if 
not corrected, could result in oxygen leaks from oxygen tube couplings 
in the passenger oxygen system, which could result in depletion of 
emergency oxygen at a faster rate than expected, reduce the passengers' 
and crews' protection from hypoxia at elevated cabin altitudes, and 
increase the risk of a fire.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Special Attention Service Bulletin 747-35-2132, 
dated June 8, 2015. The service information describes procedures for 
inspection of passenger oxygen coupler assemblies for missing oxygen 
components, installation of o-rings, and corrective actions. This 
service information is reasonably available because the interested 
parties have access to it through their normal course of business or by 
the means identified in the ADDRESSES section.

FAA's Determination

    We are issuing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

AD Requirements

    This AD requires accomplishing the actions identified in the 
service information identified previously. For information on the 
procedures and compliance times, see this service information at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-
5033.
    The phrase ``corrective actions'' is used in this AD. ``Corrective 
actions'' are actions that correct or address any condition found. 
Corrective actions in an AD could include, for example, repairs.
    This AD also requires sending the inspection results to the 
Manager, Seattle Aircraft Certification Office, FAA.

FAA's Justification and Determination of the Effective Date

    There are no products of this type currently registered in the 
United States. However, this rule is necessary to ensure that the 
described unsafe condition is addressed if any of these products are 
placed on the U.S. Register in the future. Therefore, we find that 
notice and opportunity for prior public comment are unnecessary and 
that good cause exists for making this amendment effective in less than 
30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety and was not preceded by notice and an opportunity for public 
comment. However, we invite you to send any written data, views, or 
arguments about this AD. Send your comments to an address listed under 
the ADDRESSES section. Include ``Docket No. FAA-2016-5033; Directorate 
Identifier 2015-NM-118-AD'' at the beginning of your comments. We 
specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this AD. We will consider all 
comments received by the closing date and may amend this AD because of 
those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this AD.

Costs of Compliance

    We estimate that this AD affects 0 airplanes of U.S. registry.
    We estimate the following costs to comply with this AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                     Cost per      Cost on U.S.
                Action                         Labor cost           Parts cost        product        operators
----------------------------------------------------------------------------------------------------------------
Inspection...........................  8 work-hours x $85 per                 $0            $680              $0
                                        hour = $680.
Reporting............................  1 work-hour x $85 per                   0              85               0
                                        hour = $85.
----------------------------------------------------------------------------------------------------------------

    We estimate the following costs to do any necessary corrective 
actions that will be required based on the results of the inspection. 
We have no way of determining the number of aircraft that might need 
these repairs:

                                               On-Condition Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                     Cost per
                    Action                                Labor cost               Parts cost        product
----------------------------------------------------------------------------------------------------------------
Corrective Action............................  8 work-hours x $85 per hour =            $6,888           $7,568
                                                $680.
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, some of the costs of this AD may be 
covered under warranty, thereby reducing the cost impact on affected 
individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all costs in our cost 
estimate.

Paperwork Reduction Act

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to penalty for 
failure to comply with a collection of information subject to the 
requirements of the Paperwork Reduction Act unless that collection of 
information displays a current valid OMB control number. The control 
number for the collection of information required by this AD is 2120-
0056. The paperwork cost associated with this AD has been detailed in 
the Costs of Compliance section of this document and includes time for 
reviewing instructions, as well as completing and reviewing the 
collection of information. Therefore, all reporting associated with 
this AD is mandatory. Comments concerning the accuracy of this burden 
and suggestions for reducing the burden should be directed to the FAA 
at 800 Independence Ave. SW., Washington, DC 20591, ATTN: Information 
Collection Clearance Officer, AES-200.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue

[[Page 18466]]

rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation Programs'' 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2016-07-05 The Boeing Company: Amendment 39-18450; Docket No. FAA-
2016-5033 Directorate Identifier 2015-NM-118-AD.

(a) Effective Date

    This AD is effective April 15, 2016.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Boeing Model 747-8 series airplanes, 
certificated in any category, as identified in Boeing Special 
Attention Service Bulletin 747-35-2132, dated June 8, 2015.

(d) Subject

    Air Transport Association (ATA) of America Code 35, Oxygen.

(e) Unsafe Condition

    This AD was prompted by a report of oxygen tube couplings in the 
passenger oxygen system that could be missing or incorrectly 
installed. We are issuing this AD to detect and correct oxygen leaks 
from oxygen tube couplings in the passenger oxygen system, which 
could result in depletion of emergency oxygen at a faster rate than 
expected, reduce the passengers' and crews' protection from hypoxia 
at elevated cabin altitudes, and increase the risk of a fire.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection and Corrective Actions

    Within 72 months after the effective date of this AD: Do a 
general visual inspection to determine if all oxygen components are 
installed; and do all applicable corrective actions; in accordance 
with the Accomplishment Instructions of Boeing Special Attention 
Service Bulletin 747-35-2132, dated June 8, 2015. Do all applicable 
corrective actions before further flight.

(h) Reporting

    Submit a report of the findings (both positive and negative) of 
the inspection required by paragraph (g) of this AD to the Manager, 
Seattle Aircraft Certification Office (ACO), at the applicable time 
specified in paragraph (h)(1) or (h)(2) of this AD. The report must 
include the inspection results, a description of the condition 
found, and the airplane serial number.
    (1) If the inspection was done on or after the effective date of 
this AD: Submit the report within 30 days after the inspection.
    (2) If the inspection was done before the effective date of this 
AD: Submit the report within 30 days after the effective date of 
this AD.

(i) Paperwork Reduction Act Burden Statement

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to a penalty 
for failure to comply with a collection of information subject to 
the requirements of the Paperwork Reduction Act unless that 
collection of information displays a current valid OMB Control 
Number. The OMB Control Number for this information collection is 
2120-0056. Public reporting for this collection of information is 
estimated to be approximately 5 minutes per response, including the 
time for reviewing instructions, completing and reviewing the 
collection of information. All responses to this collection of 
information are mandatory. Comments concerning the accuracy of this 
burden and suggestions for reducing the burden should be directed to 
the FAA at: 800 Independence Ave. SW., Washington, DC 20591, Attn: 
Information Collection Clearance Officer, AES-200.

(j) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or local Flight Standards District Office, as 
appropriate. If sending information directly to the manager of the 
ACO, send it to the attention of the person identified in paragraph 
(k) of this AD. Information may be emailed to: [email protected].
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) For service information that contains steps that are labeled 
as Required for Compliance (RC), the provisions of paragraphs 
(j)(3)(i) and (j)(3)(ii) apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. An AMOC is required for any deviations to RC steps, 
including substeps and identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.
    (4) An AMOC that provides an acceptable level of safety may be 
used for any repair, modification, or alteration required by this AD 
if it is approved by the Boeing Commercial Airplanes Organization 
Designation Authorization (ODA) that has been authorized by the 
Manager, Seattle ACO, to make those findings. To be approved, the 
repair method, modification deviation, or alteration deviation must 
meet the certification basis of the airplane, and the approval must 
specifically refer to this AD.

(k) Related Information

    For more information about this AD, contact Susan Monroe, 
Aerospace Engineer, Cabin Safety and Environmental Systems Branch, 
ANM-150S, FAA, Seattle ACO, 1601 Lind Avenue SW., Renton, WA; phone: 
425-917-6457; fax: 425-917-6590; email: [email protected].

[[Page 18467]]

(l) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Boeing Special Attention Service Bulletin 747-35-2132, dated 
June 8, 2015.
    (ii) Reserved.
    (3) For Boeing service information identified in this AD, 
contact Boeing Commercial Airplanes, Attention: Data & Services 
Management, P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; 
telephone 206-544-5000, extension 1; fax 206-766-5680; Internet 
https://www.myboeingfleet.com.
    (4) You may view this service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 
425-227-1221.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on March 20, 2016.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2016-07025 Filed 3-30-16; 8:45 am]
 BILLING CODE 4910-13-P