[Federal Register Volume 80, Number 154 (Tuesday, August 11, 2015)]
[Rules and Regulations]
[Pages 48013-48018]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2015-19316]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2014-0487; Directorate Identifier 2014-NM-026-AD;
Amendment 39-18226; AD 2015-16-01]
RIN 2120-AA64
Airworthiness Directives; The Boeing Company Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are superseding Airworthiness Directive (AD) 2012-19-11 for
certain The Boeing Company Model 737 airplanes. AD 2012-19-11 required
incorporating design changes to improve the reliability of the cabin
altitude warning system by installing a redundant cabin altitude
pressure switch, replacing the aural warning module (AWM) with a new or
reworked AWM, and changing certain wire bundles or connecting certain
previously capped and stowed wires as necessary. For certain airplanes,
AD 2012-19-11 also required prior or concurrent incorporation of
related design changes by modifying the instrument panels, installing
light assemblies, modifying the wire bundles, and installing a new
circuit breaker, as necessary. This AD was prompted by the report of a
flightcrew not receiving an aural warning during a lack-of-cabin
pressurization event. We are issuing this AD to prevent the loss of
cabin altitude warning, which could delay flightcrew recognition of a
lack of cabin pressurization, and could result in incapacitation of the
flightcrew due to hypoxia (a lack of oxygen in the body), and
consequent loss of control of the airplane.
DATES: This AD is effective September 15, 2015.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in this AD as of September 15,
2015.
The Director of the Federal Register approved the incorporation by
reference of certain other publications listed in this AD as of
November 7, 2012 (77 FR 60296, October 3, 2012).
ADDRESSES: For service information identified in this AD, contact
Boeing Commercial Airplanes, Attention: Data & Services Management, P.
O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-5000,
extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com.
You may view this referenced service information at the FAA, Transport
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information
on the availability of this material at the FAA, call 425-227-1221.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0487; or in person at the Docket Management Facility between 9 a.m. and
5 p.m., Monday through Friday, except Federal holidays. The AD docket
contains this AD, the regulatory evaluation, any comments received, and
other information. The address for the Docket Office (phone: 800-647-
5527) is Docket Management Facility, U.S. Department of Transportation,
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200
New Jersey Avenue SE., Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Francis Smith, Aerospace Engineer,
Cabin Safety and Environmental Systems Branch, ANM-150S, FAA, Seattle
Aircraft Certification Office, 1601 Lind Avenue SW., Renton, WA 98057-
3356; telephone: 425-917-6596; fax: 425-917-6590; email:
[email protected].
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR
part 39 to supersede AD 2012-19-11, Amendment 39-17206 (77 FR 60296,
October 3, 2012). AD 2012-19-11
[[Page 48014]]
applied to certain The Boeing Company Model 737 airplanes. The NPRM
published in the Federal Register on July 29, 2014 (79 FR 43983).
The NPRM was prompted by the report of a flightcrew not receiving
an aural warning during a lack of cabin pressurization event. The NPRM
proposed to continue to require incorporating design changes to improve
the reliability of the cabin altitude warning system by installing a
redundant cabin altitude pressure switch, replacing the AWM with a new
or reworked AWM, and changing certain wire bundles or connecting
certain previously capped and stowed wires as necessary.
For certain airplanes, the NPRM proposed to continue to require
prior or concurrent incorporation of related design changes by
modifying the instrument panels, installing light assemblies, modifying
the wire bundles, and installing a new circuit breaker, as necessary.
The NPRM also proposed to require, for certain airplanes, incorporating
related design changes. The NPRM also proposed, for certain airplanes,
to no longer give credit for the prior accomplishment of certain
actions. We are issuing this AD to prevent the loss of cabin altitude
warning, which could delay flightcrew recognition of a lack of cabin
pressurization, and could result in incapacitation of the flightcrew
due to hypoxia (a lack of oxygen in the body), and consequent loss of
control of the airplane.
Comments
We gave the public the opportunity to participate in developing
this AD. The following presents the comments received on the NPRM (79
FR 43983, July 29, 2014) and the FAA's response to each comment.
Request To Use the Latest Service Information
Boeing requested that the proposed rule (79 FR 43983, July 29,
2014) incorporate Boeing Special Attention Service Bulletin 737-21-
1165, Revision 3, dated July 16, 2014, and Boeing Alert Service
Bulletin 737-31A1325, Revision 2, dated June 5, 2014. Boeing stated
that it has released new service information and the service
information should be reflected in the proposed rule.
We agree with the commenter's request to reference the latest
service information. We have revised this final rule accordingly.
Boeing Alert Service Bulletin 737-31A1325, Revision 2, dated June
5, 2014, updates reference document names, corrects typographical
errors, and includes airplanes that were removed in error in an earlier
revision of the service information. The procedures remain unchanged.
In addition, we have added paragraph (j)(2) of this AD, to give credit
for previous actions, if those actions were performed before the
effective date of this AD using Boeing Alert Service Bulletin 737-
31A1325, dated January 11, 2010, and Boeing Alert Service Bulletin 737-
31A1325, Revision 1, dated July 5, 2012.
Boeing Special Attention Service Bulletin 737-21-1165, Revision 3,
dated July 16, 2014, includes configuration differences found by
operators during incorporation of earlier revisions of the service
information. The procedures otherwise remain unchanged.
Request To Add an Exception to the Proposed Rule (79 FR 43983, July 29,
2014)
An anonymous commenter requested to add an exception to the
proposed rule (79 FR 43983, July 29, 2014). The commenter stated that
paragraphs (j)(2) and (j)(3) of the proposed AD should include the same
exceptions for group 24 through 25 airplanes, and group 27 through 33
airplanes, as identified in Boeing Alert Service Bulletin 737-31A1332,
Revision 4, dated October 31, 2013.
The commenter also stated that paragraphs (i)(2) and (i)(3) of AD
2012-19-11, Amendment 39-17206 (77 FR 60296, October 3, 2012), did not
give credit for previous actions for group 24 through 25 airplanes, and
group 27 through 33 airplanes, as identified in Boeing Alert Service
Bulletin 737-31A1332, Revision 3, dated March 28, 2012. The commenter
stated that this is because paragraph 1.C. of Boeing Alert Service
Bulletin 737-31A1332, Revision 3, dated March 28, 2012, explicitly
states that changes given in figures 48 through 50 affect wiring
changes previously accomplished in Boeing Service Bulletin 737-24A1141;
also figures 15 through 17, and airplane line numbers 1 through 740,
are moved to a new group 24 through 25 airplanes, and group 27 through
33 airplanes.
The commenter stated that if an airplane is identified in groups 24
through 25 airplanes, and group 27 through 33 airplanes, of Boeing
Alert Service Bulletin 737-31A1332, Revision 4, dated October 31, 2013,
the operator can take credit for previous actions accomplished using
Boeing Alert Service Bulletin 737-31A1332, Revision 2, dated August 18,
2011, and Boeing Alert Service Bulletin 737-31A1332, Revision 1, dated
June 24, 2010. Therefore, the commenter stated that the operator must,
per the exceptions of paragraphs (i)(2) or (i)(3) of AD 2012-19-11,
Amendment 39-17206 (77 FR 60296, October 3, 2012), re-comply with the
proposed AD once the additional actions are taken.
We disagree with the commenter's request. This AD corrects an error
in paragraph (i) of AD 2012-19-11, Amendment 39-17206 (77 FR 60296,
October 3, 2012). In AD 2012-19-11, airplanes were identified
incorrectly as having wiring instructions that may conflict with the
corrective actions of AD 2009-16-07, Amendment 39-15990 (74 FR 41607,
August 18, 2009). Further, this AD supersedes (i.e., ``replaces'') AD
2012-19-11, and therefore compliance is required with this new AD only.
In addition, there are still exclusions in this AD, but they are now
identified by line numbers--not by groups--as shown in paragraphs
(j)(1)(ii) and (j)(1)(iii) of this AD. We have not changed this AD in
this regard.
Request To Extend the Compliance Time
United Airlines (UAL) requested that the compliance time for the
proposed rule (79 FR 43983, July 29, 2014) be extended a minimum of 1
year for all airplanes. UAL stated that this is due to the increased
scope of required testing not documented in Boeing Special Attention
Service Bulletin 737-21-1165, Revision 1, dated July 16, 2010, as
revised by Boeing Special Attention Service Bulletin 737-21-1165,
Revision 2, dated April 30, 2012. UAL commented that Boeing Special
Attention Service Bulletin 737-21-1165, Revision 2, dated April 30,
2012, is for the removal of the junction box 46, and additional
administrative time is required during the accomplishment of each
airplane for obtaining an alternate method of compliance (AMOC).
UAL commented that due to the removal of junction box 46, 43
additional operational checks must be accomplished and are estimated to
take an additional 30 hours of elapsed time for each airplane. UAL
stated that the estimated costs of the proposed rule (79 FR 43983, July
29, 2014) should be revised to include an additional 30 hours for
testing.
UAL also stated that multiple AMOCs have been required for the
concurrent requirements and for airplanes affected by AD 2013-02-05,
Amendment 39-17326 (78 FR 6202, January 30, 2013) due to errors in the
Boeing data. UAL stated that the time necessary to seek approved AMOCs
extends the completion time of each airplane beyond the time allotted
in the estimated costs and can result in the airplanes being out of
service.
[[Page 48015]]
We disagree with the commenter's request. Boeing has provided its
work estimates based on average times for accomplishing its service
information specifically to correct the unsafe condition. The time
spent to perform additional functional checks and testing to systems
incidentally associated with the unsafe condition in this AD and any
associated administrative actions in carrying out all work (related to
this AD) will vary among operators. Additionally, we do not consider
the time spent processing AMOCs when we determine estimated costs of an
AD because of the variable occurrences, scope of technical deviations,
and elective nature of many AMOC requests.
The estimate of labor hours provides only a guideline for
operators, and operators are encouraged to review all relevant work
steps to create time and cost estimates specific to their schedules and
work processes. Operators that request AMOCs while their airplane is in
maintenance do not have to wait for the Seattle Aircraft Certification
Office (ACO) approval before they can return the airplane to service,
provided the 72-month compliance time has not passed, and operators do
not claim compliance credit in their maintenance records until the AMOC
is received. As long as the 72-month compliance time has not been
exceeded, an AMOC is not needed; therefore, requests for compliance
time extensions and Seattle ACO responses to early AMOC requests have
no effect on returning an airplane to service from an operator's
maintenance cycle.
We base AD compliance times primarily on our assessment of safety
risk. We consider the overall risk to the fleet, including the severity
of the failure and the likelihood of the failure's occurrence in
development of the compliance time for the ADs. We work with the
respective manufacturers to ensure that all appropriate instructions
and parts are available at the appropriate time to meet our collective
safety goals, and that those goals are based on safety of the fleet. We
have not changed this AD in this regard.
Effect of Winglets on AD
Aviation Partners Boeing stated that the installation of winglets
per STC ST01219SE or ST00830SE does not affect the accomplishment of
the manufacturer's service instructions.
Conclusion
We reviewed the relevant data, considered the comments received,
and determined that air safety and the public interest require adopting
this AD with the changes described previously and minor editorial
changes. We have determined that these minor changes:
Are consistent with the intent that was proposed in the
NPRM (79 FR 43983, July 29, 2014) for correcting the unsafe condition;
and
Do not add any additional burden upon the public than was
already proposed in the NPRM (79 FR 43983, July 29, 2014).
We also determined that these changes will not increase the
economic burden on any operator or increase the scope of this AD.
Related Service Information Under 1 CFR Part 51
We reviewed the following service information:
Boeing Alert Service Bulletin 737-31A1325, Revision 2,
dated June 5, 2014.
Boeing Alert Service Bulletin 737-31A1332, Revision 4,
dated October 31, 2013.
Boeing Special Attention Service Bulletin 737-21-1164,
Revision 2, dated August 23, 2013.
Boeing Special Attention Service Bulletin 737-21-1165,
Revision 3, dated July 16, 2014.
The service information describe procedures for incorporating
design changes to improve the reliability of the cabin altitude warning
system by installing a redundant cabin altitude pressure switch,
replacing the AWM with a new or reworked AWM, and changing certain wire
bundles or connecting certain previously capped and stowed wires as
necessary. This service information is reasonably available because the
interested parties have access to it through their normal course of
business or by the means identified in the ADDRESSES section of this
AD.
Costs of Compliance
We estimate that this AD affects 1,618 airplanes of U.S. registry.
We estimate the following costs to comply with this AD:
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost on U.S.
Action Labor cost Parts cost Cost per product operators
----------------------------------------------------------------------------------------------------------------
Install a redundant cabin Up to 62 $33,576 Up to $38,846...... Up to $62,852,828
altitude pressure switch, work[dash]hours x
replace the AWM with a new or $85 per hour = up
reworked AWM, change certain to $5,270.
wire bundles or connect certain
capped and stowed wires
[retained actions from AD 2012-
19-11, Amendment 39-17206 (77 FR
60296, October 3, 2012), for
1,618 airplanes].
Modify the instrument panels, Up to 92 5,292 Up to $13,112...... Up to $20,926,752
install light assemblies, modify work[dash]hours x
the wire bundles, and install a $85 per hour = up
new circuit breaker (concurrent to $7,820.
requirements) [retained actions
from AD 2012-19-11, Amendment 39-
17206 (77 FR 60296, October 3,
2012), for 1,596 airplanes].
Modify the instrument panels, Up to 92 5,292 Up to $13,112...... Up to $288,464
install light assemblies, modify work[dash]hours x
the wire bundles, and install a $85 per hour = up
new circuit breaker (concurrent to $7,820.
requirements) [new actions for
22 airplanes].
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII,
[[Page 48016]]
Part A, Subpart III, Section 44701, ``General requirements.'' Under
that section, Congress charges the FAA with promoting safe flight of
civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979),
(3) Will not affect intrastate aviation in Alaska, and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by removing Airworthiness Directive (AD)
2012-19-11, Amendment 39-17206 (77 FR 60296, October 3, 2012), and
adding the following new AD:
2015-16-01 The Boeing Company: Amendment 39-18226; Docket No. FAA-
2014-0487; Directorate Identifier 2014-NM-026-AD.
(a) Effective Date
This AD is effective September 15, 2015.
(b) Affected ADs
This AD replaces AD 2012-19-11, Amendment 39-17206 (77 FR 60296,
October 3, 2012).
(c) Applicability
This AD applies to The Boeing Company airplanes, certificated in
any category, as identified in paragraphs (c)(1) and (c)(2) of this
AD.
(1) Model 737-100, -200, -200C, -300,--400, and -500 series
airplanes, as identified in Boeing Special Attention Service
Bulletin 737-21-1164, Revision 2, dated August 23, 2013.
(2) Model 737-600, -700, -700C, -800, -900, and -900ER series
airplanes, as identified in Boeing Special Attention Service
Bulletin 737-21-1165, Revision 3, dated July 16, 2014.
(d) Subject
Air Transport Association (ATA) of America Code 21, Air
Conditioning.
(e) Unsafe Condition
This AD was prompted by the report of a flightcrew not receiving
an aural warning during a lack of cabin pressurization event. We are
issuing this AD to prevent the loss of cabin altitude warning, which
could delay flightcrew recognition of a lack of cabin
pressurization, and could result in incapacitation of the flightcrew
due to hypoxia (a lack of oxygen in the body), and consequent loss
of control of the airplane.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Retained Installation
This paragraph restates the actions required by paragraph (g) of
AD 2012-19-11, Amendment 39-17206 (77 FR 60296, October 3, 2012),
with revised service information. Within 72 months after November 7,
2012 (the effective date of AD 2012-19-11), install a redundant
cabin altitude pressure switch, replace the aural warning module
(AWM) with a new or reworked AWM, and change certain wire bundles or
connect certain capped and stowed wires, as applicable, in
accordance with the Accomplishment Instructions of the applicable
service information in paragraphs (g)(1) and (g)(2) of this AD;
except as provided by paragraph (k)(1) of this AD.
(1) Boeing Special Attention Service Bulletin 737-21-1164,
Revision 1, dated May 17, 2012; or Boeing Special Attention Service
Bulletin 737-21-1164, Revision 2, dated August 23, 2013 (for Model
737-100, -200, -200C, -300, -400, and -500 series airplanes). As of
the effective date of this AD, use Boeing Special Attention Service
Bulletin 737-21-1164, Revision 2, dated August 23, 2013, for the
actions specified in paragraph (g) of this AD.
(2) Boeing Special Attention Service Bulletin 737-21-1165,
Revision 1, dated July 16, 2010, as revised by Boeing Special
Attention Service Bulletin 737-21-1165, Revision 2, dated April 30,
2012; or Boeing Special Attention Service Bulletin 737-21-1165,
Revision 3, dated July 16, 2014 (for Model 737-600, -700, -700C, -
800, -900, and -900ER series airplanes). As of the effective date of
this AD use Boeing Special Attention Service Bulletin 737-21-1165,
Revision 3, dated July 16, 2014.
(h) Retained Concurrent Actions
This paragraph restates the concurrent actions required by
paragraph (h) of AD 2012-19-11, Amendment 39-17206 (77 FR 60296,
October 3, 2012), with revised service information. For airplanes
identified in Boeing Alert Service Bulletin 737-31A1325, dated
January 11, 2010 (for Model 737-100, -200, -200C, -300, -400, and -
500 series airplanes); and Boeing Alert Service Bulletin 737-
31A1332, Revision 3, dated March 28, 2012 (for Model 737-600, -700,
-700C, -800, -900, and -900ER series airplanes); except as provided
by paragraph (i) of this AD: Before or concurrently with
accomplishment of the actions specified in paragraph (g) of this AD,
as applicable, modify the instrument panels, install light
assemblies, modify the wire bundles, and install a new circuit
breaker, in accordance with the Accomplishment Instructions of the
applicable service information in paragraphs (h)(1) and (h)(2) of
this AD; except as provided by paragraph (k)(2) of this AD.
(1) The service information for Model 737-100, -200, -200C, -
300, -400, and -500 series airplanes as identified in paragraphs
(h)(1)(i), (h)(1)(ii), and (h)(1)(iii), of this AD. As of the
effective date of this AD, use Boeing Alert Service Bulletin 737-
31A1325, Revision 2, dated June 5, 2014 (for Model 737-100, -200, -
200C, -300, -400, and -500 series airplanes), for the actions
specified in paragraph (h) of this AD.
(i) Boeing Alert Service Bulletin 737-31A1325, dated January 11,
2010.
(ii) Boeing Alert Service Bulletin 737-31A1325, Revision 1,
dated July 5, 2012.
(iii) Boeing Alert Service Bulletin 737-31A1325, Revision 2,
dated June 5, 2014.
(2) Boeing Alert Service Bulletin 737-31A1332, Revision 3, dated
March 28, 2012; or Boeing Alert Service Bulletin 737-31A1332,
Revision 4, dated October 31, 2013 (for Model 737-600, -700, -700C,
-800, -900, and -900ER series airplanes). As of the effective date
of this AD, use Boeing Alert Service Bulletin 737-31A1332, Revision
4, dated October 31, 2013 (for Model 737-600, -700, -700C, -800, -
900, and -900ER series airplanes), for the actions specified in
paragraph (h) of this AD.
(i) New Concurrent Requirement
For airplanes having variable numbers YA001 through YA008
inclusive, YA251, YA501 through YA508 inclusive, and YC321 through
YC325 inclusive: Before or concurrently with accomplishment of the
actions specified in paragraph (g) of this AD, or within 18 months
after the effective date of this AD, whichever occurs later, modify
the instrument panels, install light assemblies, modify the wire
bundles, and install a new circuit breaker, in accordance with the
Accomplishment Instructions of Boeing Alert Service Bulletin 737-
31A1332, Revision 4, dated October 31, 2013.
[[Page 48017]]
(j) Credit for Previous Actions
(1) This paragraph restates the credit for previous actions
stated in paragraph (i) of AD 2012-19-11, Amendment 39-17206 (77 FR
60296, October 3, 2012), with correct paragraph reference and
revised exempted airplanes.
(i) This paragraph provides credit for the actions required by
paragraph (g) of this AD, if those actions were performed before
November 7, 2012 (the effective date of AD 2012-19-11, Amendment 39-
17206 (77 FR 60296, October 3, 2012)), using Boeing Special
Attention Service Bulletin 737-21-1165, Revision 1, dated July 16,
2010, which was incorporated by reference in AD 2012-19-11.
(ii) For airplanes identified in Boeing Alert Service Bulletin
737-31A1332, Revision 1, dated June 24, 2010; except airplanes
having variable numbers YA001 through YA019 inclusive, YA201 through
YA203 inclusive, YA231 through YA242 inclusive, YA251, YA252, YA271,
YA272, YA301, YA302, YA311, YA312, YA501 through YA508 inclusive,
YA541, YA701, YA702, YC001 through YC007 inclusive, YC051, YC052,
YC101, YC102, YC111, YC121, YC301, YC302, YC321 through YC330
inclusive, YC381, YC401 through YC403 inclusive, YC501, YC502, and
YE001 through YE003 inclusive: This paragraph provides credit for
the actions required by paragraph (h) of this AD, if those actions
were performed before the effective date of this AD using Boeing
Alert Service Bulletin 737-31A1332, Revision 1, dated June 24, 2010,
which was incorporated by reference in AD 2012-19-11, Amendment 39-
17206 (77 FR 60296, October 3, 2012).
(iii) For airplanes identified in Boeing Alert Service Bulletin
737-31A1332, Revision 2, dated August 18, 2011; except airplanes
identified in paragraph (j)(4) of this AD and airplanes having
variable numbers YA001 through YA019 inclusive, YA201 through YA203
inclusive, YA231 through YA242 inclusive, YA251, YA252, YA271,
YA272, YA301, YA302, YA311, YA312, YA501 through YA508 inclusive,
YA541, YA701, YA702, YC001 through YC007 inclusive, YC051, YC052,
YC101, YC102, YC111, YC121, YC301, YC302, YC321 through YC330
inclusive, YC381, YC401 through YC403 inclusive, YC501, YC502, and
YE001 through YE003 inclusive: This paragraph provides credit for
the actions required by paragraph (h) of this AD, if those actions
were performed before the effective date of this AD using Boeing
Alert Service Bulletin 737-31A1332, Revision 2, dated August 18,
2011, which was incorporated by reference in AD 2012-19-11,
Amendment 39-17206 (77 FR 60296, October 3, 2012).
(iv) For Group 21, Configuration 2 airplanes identified in
Boeing Alert Service Bulletin 737-31A1332, Revision 3, dated March
28, 2012: This paragraph provides credit for the actions required by
paragraph (h) of this AD, if those actions were performed before the
effective date of this AD using Boeing Alert Service Bulletin 737-
31A1332, Revision 2, dated August 18, 2011, which was incorporated
by reference in AD 2012-19-11, Amendment 39-17206 (77 FR 60296,
October 3, 2012); and provided that the actions specified in Boeing
Service Bulletin 737-21-1171, dated February 12, 2009 (which is not
incorporated by reference in this AD), were accomplished prior to or
concurrently with the actions specified in Boeing Alert Service
Bulletin 737-31A1332, Revision 2, dated August 18, 2011.
(2) This paragraph provides credit for the actions specified in
paragraph (h) of this AD, if those actions were performed before the
effective date of this AD using the service information identified
in paragraph (j)(2)(i) or (j)(2)(ii) of this AD.
(i) Boeing Alert Service Bulletin 737-31A1325, dated January 11,
2010, which was incorporated by reference in AD 2012-19-11,
Amendment 39-17206 (77 FR 60296, October 3, 2012).
(ii) Boeing Alert Service Bulletin 737-31A1325, Revision 1,
dated July 5, 2012, which is not incorporated by reference in this
AD.
(k) New Requirements to This AD: Exceptions to the Service Information
(1) Where Boeing Special Attention Service Bulletin 737-21-1164,
Revision 2, dated August 23, 2013, specifies to contact Boeing for
instructions: Before further flight, repair using a method approved
in accordance with the procedures specified in paragraph (l) of this
AD.
(2) Where Boeing Alert Service Bulletin 737-31A1325, Revision 2,
dated June 5, 2014, specifies to contact Boeing for instructions:
Before further flight, repair using a method approved in accordance
with the procedures specified in paragraph (l) of this AD.
(l) Alternative Methods of Compliance (AMOCs)
(1) The Manager, Seattle Aircraft Certification Office (ACO),
FAA, has the authority to approve AMOCs for this AD, if requested
using the procedures found in 14 CFR 39.19. In accordance with 14
CFR 39.19, send your request to your principal inspector or local
Flight Standards District Office, as appropriate. If sending
information directly to the manager of the ACO, send it to the
attention of the person identified in paragraph (m)(1) of this AD.
Information may be emailed to: [email protected].
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
(3) An AMOC that provides an acceptable level of safety may be
used for any repair required by this AD if it is approved by the
Boeing Commercial Airplanes Organization Designation Authorization
(ODA) that has been authorized by the Manager, Seattle ACO, to make
those findings. For a repair method to be approved, the repair must
meet the certification basis of the airplane, and the approval must
specifically refer to this AD.
(4) AMOCs approved for AD 2012-19-11, Amendment 39-17206 (77 FR
60296, October 3, 2012), are approved as AMOCs for the corresponding
provisions of this AD.
(m) Related Information
(1) For more information about this AD, contact Francis Smith,
Aerospace Engineer, Cabin Safety and Environmental Systems Branch,
ANM-150S, FAA, Seattle Aircraft Certification Office, 1601 Lind
Avenue SW., Renton, WA 98057-3356; phone: 425-917-6596; fax: 425-
917-6590; email: [email protected].
(2) Service information identified in this AD that is not
incorporated by reference is available at the addresses specified in
paragraphs (n)(5) and (n)(6) of this AD.
(n) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless the AD specifies otherwise.
(3) The following service information was approved for IBR on
September 15, 2015.
(i) Boeing Alert Service Bulletin 737-31A1325, Revision 2, dated
June 5, 2014.
(ii) Boeing Alert Service Bulletin 737-31A1332, Revision 4,
dated October 31, 2013.
(iii) Boeing Special Attention Service Bulletin 737-21-1164,
Revision 2, dated August 23, 2013.
(iv) Boeing Special Attention Service Bulletin 737-21-1165,
Revision 3, dated July 16, 2014.
(4) The following service information was approved for IBR on
November 7, 2012 (77 FR 60296, October 3, 2012).
(i) Boeing Alert Service Bulletin 737-31A1325, dated January 11,
2010.
(ii) Boeing Alert Service Bulletin 737-31A1332, Revision 1,
dated June 24, 2010.
(iii) Boeing Alert Service Bulletin 737-31A1332, Revision 2,
dated August 18, 2011.
(iv) Boeing Alert Service Bulletin 737-31A1332, Revision 3,
dated March 28, 2012.
(v) Boeing Special Attention Service Bulletin 737-21-1164,
Revision 1, dated May 17, 2012.
(vi) Boeing Special Attention Service Bulletin 737-21-1165,
Revision 1, dated July 16, 2010.
(vii) Boeing Special Attention Service Bulletin 737-21-1165,
Revision 2, dated April 30, 2012.
(5) For Boeing service information identified in this AD,
contact Boeing Commercial Airplanes, Attention: Data & Services
Management, P. O. Box 3707, MC 2H-65, Seattle, WA 98124-2207;
telephone 206-544-5000, extension 1; fax 206-766-5680; Internet
https://www.myboeingfleet.com.
(6) You may view this referenced service information at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA.
For information on the availability of this material at the FAA,
call 425-227-1221.
(7) You may view this service information that is incorporated
by reference at the National Archives and Records Administration
(NARA). For information on the availability of this material at
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.
[[Page 48018]]
Issued in Renton, Washington, on July 22, 2015.
Victor Wicklund,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 2015-19316 Filed 8-10-15; 8:45 am]
BILLING CODE 4910-13-P