[Federal Register Volume 80, Number 130 (Wednesday, July 8, 2015)]
[Rules and Regulations]
[Pages 38959-38966]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2015-16627]
-----------------------------------------------------------------------
ENVIRONMENTAL PROTECTION AGENCY
40 CFR Part 52
[EPA-R09-OAR-2015-0164; FRL-9927-76-Region 9]
Revisions to the California State Implementation Plan, Feather
River Air Quality Management District
AGENCY: Environmental Protection Agency (EPA).
ACTION: Direct final rule.
-----------------------------------------------------------------------
SUMMARY: The Environmental Protection Agency (EPA) is taking direct
final action to approve revisions to the Feather River Air Quality
Management District (FRAQMD or the District) portion of the California
State Implementation Plan (SIP). Included in this approval are the
following three SIP demonstrations from FRAQMD: 2006 Reasonably
Available Control Technology (RACT) Analysis for State Implementation
Plan (SIP), November 2006; Reasonably Available Control Technology
State Implementation Plan Revision Negative Declaration for Control
Techniques Guidelines Issued 2006-2008, June 1, 2009 and; Reasonably
Available Control Technology Analysis and Negative Declarations, July
3, 2014. The first two demonstrations address the 1997 8-hour National
Ambient Air Quality Standards (NAAQS) for ozone, and the third
demonstration addresses the 2008 8-hour NAAQS for ozone. These
submitted SIP revisions contain FRAQMD's negative declarations for
volatile organic compound (VOC) source categories. We are approving the
submitted SIP revisions under the Clean Air Act as amended in 1990 (CAA
or the Act). We are also approving a local rule to regulate VOC
emissions from gasoline dispensing facilities.
DATES: This rule is effective on September 8, 2015 without further
notice, unless EPA receives adverse comments by August 7, 2015. If we
receive such comments, we will publish a timely withdrawal in the
Federal Register to notify the public that this direct final rule will
not take effect.
ADDRESSES: Submit comments, identified by docket number EPA-R09-OAR-
2015-0164, by one of the following methods:
1. Federal eRulemaking Portal: www.regulations.gov. Follow the on-
line instructions.
2. Email: [email protected].
3. Mail or deliver: Andrew Steckel (Air-4), U.S. Environmental
Protection Agency Region IX, 75 Hawthorne Street, San Francisco, CA
94105-3901.
Instructions: All comments will be included in the public docket
without change and may be made available online at www.regulations.gov,
including any personal information provided, unless the comment
includes Confidential Business Information (CBI) or other information
whose disclosure is restricted by statute. Information that you
consider CBI or otherwise protected should be clearly identified as
such and should not be submitted through www.regulations.gov or email.
www.regulations.gov is an ``anonymous access'' system, and EPA will not
know your identity or contact information unless you provide it in the
body of your comment. If you send email directly to EPA, your email
address will be automatically captured and included as part of the
public comment. If EPA cannot read your comment due to technical
difficulties and cannot contact you for clarification, EPA may not be
able to consider your comment. Electronic files should avoid the use of
special characters, any form of encryption, and be free of any defects
or viruses.
Docket: Generally, documents in the docket for this action are
available electronically at www.regulations.gov and in hard copy at EPA
Region IX, 75 Hawthorne Street, San Francisco, California. While all
documents in the docket are listed at www.regulations.gov, some
information may be publicly available only at the hard copy location
(e.g., copyrighted material, large maps), and some may not be publicly
available in either location (e.g., CBI). To inspect the hard copy
materials, please schedule an appointment during normal business hours
with the contact listed in the FOR FURTHER INFORMATION CONTACT section.
FOR FURTHER INFORMATION CONTACT: James Shears, EPA Region IX, (213)
244-1810, [email protected].
SUPPLEMENTARY INFORMATION: Throughout this document, ``we,'' ``us'' and
``our'' refer to EPA.
Table of Contents
I. The State's Submittal
A. What documents and what rule did the state submit?
B. Are there other versions of the documents and rule?
C. What is the purpose of the RACT SIP submissions and the
purpose of the submitted rule revisions?
II. EPA's Evaluation and Action
A. How is EPA evaluating the RACT SIP submissions and the rule?
B. Do the RACT SIP submissions and the rule meet the evaluation
criteria?
C. EPA's Recommendations To Strengthen the RACT SIP and To
Further Improve the Rule
D. Public Comment and Final Action
III. Incorporation by Reference
IV. Statutory and Executive Order Reviews
[[Page 38960]]
I. The State's Submittal.
A. What documents and what rule did the state submit?
Table 1 lists the RACT SIP documents addressed by this action with
the date that each one was adopted by the local air agency and
submitted to EPA by the California Air Resources Board (CARB).
Table 1--Submitted Documents
------------------------------------------------------------------------
Local agency Document Adopted Submitted
------------------------------------------------------------------------
FRAQMD............ 2006 Reasonably 12/4/06 7/11/07
Available Control
Technology (RACT)
Analysis for State
Implementation Plan
(SIP) (``2006 RACT
SIP'').
FRAQMD............ Reasonably Available 6/1/09 10/27/09
Control Technology
State
Implementation Plan
Revision, Negative
Declaration for
Control Techniques
Guidelines Issued
2006-2008 (``2009
RACT SIP'').
FRAQMD............ Reasonably Available 8/4/14 9/29/14
Control Technology
Analysis and
Negative
Declarations
(``2014 RACT SIP'').
------------------------------------------------------------------------
The FRAQMD 2006 RACT SIP submittal became complete by operation of
law on January 11, 2008, and the FRAQMD 2009 RACT SIP submittal became
complete by operation of law on April 27, 2010, each pursuant to CAA
section 110(k)(1)(B). On January 23, 2015, EPA determined that the
submittal for the FRAQMD 2014 RACT SIP met the completeness criteria in
40 CFR part 51 Appendix V, which must be met before formal EPA review.
For the rule submitted by the state, Table 2 lists the rule we are
approving with the dates it was adopted by the local air agency and
submitted to EPA by CARB.
Table 2--Submitted Rule
----------------------------------------------------------------------------------------------------------------
Local agency Rule No. Document Amended Submitted
----------------------------------------------------------------------------------------------------------------
FRAQMD........................ 3.8 Gasoline Dispensing Facilities.. 6/2/14 11/6/14
----------------------------------------------------------------------------------------------------------------
B. Are there other versions of these documents and the rule?
There are no previous submitted versions of FRAQMD's 2006, 2009,
and 2014 RACT SIPs. For Rule 3.8, we approved an early version: The
Sutter County Rule 3.08(3.8), ``Storage and Transfer of Gasoline'', on
May 3, 1982 (47 FR 18856). With the formation of FRAQMD in 1991, this
rule was adopted with identical language in June 1991 to apply beyond
just Sutter County to the entire larger FRAQMD area.
C. What is the purpose of the RACT SIP submissions and the submitted
rule revision?
VOCs and nitrogen oxides (NOX) help produce ground-level
ozone and smog, which harm human health and the environment. Section
110(a) of the CAA requires states to submit enforceable regulations
that control VOC and NOX emissions. Sections 182(b)(2) and
(f) require that SIPs for ozone nonattainment areas classified as
moderate or above require implementation of RACT for any source covered
by an EPA Control Techniques Guidance (CTG) document and any other
major stationary source of VOCs or NOX. FRAQMD is subject to
this requirement as the southern part of Sutter County in FRAQMD is
designated and classified as a severe ozone nonattainment area for the
1997 and 2008 8-hour NAAQS for ozone (see 40 CFR 81.305). Therefore,
FRAQMD must, at a minimum, adopt RACT-level controls for all sources
covered by a CTG document and for all major non-CTG stationary sources
of VOCs or NOX in south Sutter County. The District adopted
its 2006 RACT SIP, with negative declarations, on December 4, 2006.
FRAQMD adopted its 2009 RACT SIP revision, which included negative
declarations for 11 new or updated CTGs issued from 2006 to 2008, on
June 1, 2009. FRAQMD adopted its 2014 RACT SIP, with negative
declarations, on August 2014. No comments were received on any of the
three RACT SIP demonstrations. Along with the 2014 RACT SIP adoption,
FRAQMD adopted Rule 3.8 which is designed to limit VOC emissions from
displaced gasoline vapors while transferring gasoline into storage
tanks and transport vessels. This rule is intended to fully satisfy the
CTG design criteria for Stage I vapor control systems.
II. EPA's Evaluation and Action
A. How is EPA evaluating the RACT SIP submissions and the submitted
rule revision?
FRAQMD regulates the Yuba County and Sutter County portions of the
Sacramento Valley Air Basin. The southern part of Sutter County is
designated and classified as a severe ozone nonattainment area for the
1997 and 2008 8-hour national ambient air quality standards (NAAQS) for
ozone (40 CFR 81.305). CAA Section 182(b)(2) and (f), as well as 40 CFR
51.912(a)(1) require that SIPs for ozone nonattainment areas classified
as moderate or above require implementation of RACT for any source
covered by a CTG document and any other major stationary source of VOCs
or NOX. Any stationary source that emits or has a potential
to emit at least 25 tons per year (tpy) of VOCs or NOX in a
severe ozone nonattainment area is considered a major stationary source
(see CAA sections 182(b(2)) and (f) and 302(j)). Where there are no
existing sources covered by a particular CTG document or no other major
stationary sources of VOCs or NOX, states may, in lieu of
adopting RACT requirements, adopt negative declarations certifying that
there are no such sources in the relevant nonattainment area (see
Memorandum from William T. Harnett to Regional Air Division Directors,
(May 18, 2006), ``RACT Qs & As--Reasonably Available Control Technology
(RACT) Questions and Answers'' page 7).
SIP rules must be enforceable (see CAA section 110(a)(2)), must not
interfere with applicable requirements concerning attainment and
reasonable further progress or other CAA requirements (see CAA section
110(l)),
[[Page 38961]]
and must not modify certain SIP control requirements in nonattainment
areas without ensuring equivalent or greater emissions reductions (see
CAA section 193).
Guidance and policy documents that we used to evaluate CAA section
182 RACT SIPs for FRAQMD include the following:
1. ``Final Rule to Implement the 8-Hour Ozone National Ambient Air
Quality Standard--Phase 2'' (70 FR 71612; November 29, 2005).
2. ``Air Quality Designations and Classifications for the 8-Hour
Ozone National Ambient Air Quality Standards; Early Action Compact
Areas With Deferred Dates''--Final Rule (69 FR 23858; April 30, 2004).
3. ``State Implementation Plans, General Preamble for the
Implementation of Title I of the Clean Air Act Amendments of 1990'' (57
FR 13498; April 16, 1992).
4. Issues Relating to VOC Regulation Cutpoints, Deficiencies, and
Deviations: Clarification to Appendix D of November 24, 1987 Federal
Register, May 25, 1988, Revised January 11, 1990, U.S. EPA, Air Quality
Management Division, Office of Air Quality Planning and Standards
(``The Blue Book'').
5. Guidance Document for Correcting Common VOC and Other Rule
Deficiencies, August 21, 2001, U.S. EPA Region IX (the ``Little
Bluebook'').
6. ``State Implementation Plans; Nitrogen Oxides Supplement to the
General Preamble for the Implementation of Title I of the Clean Air Act
Amendments of 1990'' (57 FR 55620, November 25, 1992) (``the
NOX Supplement'').
7. Memorandum from William T. Harnett to Regional Air Division
Directors, (May 18, 2006), ``RACT Qs & As--Reasonably Available Control
Technology (RACT) Questions and Answers.''
8. RACT SIPs, Letter dated March 9, 2006 from EPA Region IX (Andrew
Steckel) to CARB (Kurt Karperos) describing Region IX's understanding
of what constitutes a minimally acceptable RACT SIP.
9. ``Final Rule to Implement the 1997 8-Hour Ozone National Ambient
Air Quality Standard: Classification of Areas That Were Initially
Classified Under Subpart 1; Revision of the Anti-Backsliding Provisions
To Address 1-Hour Contingency Measure Requirements; Deletion of
Obsolete 1-Hour Standard Provision''--Final Rule (77 FR 28424; May 14,
2012).
10. ``Model Volatile Organic Compound Rules for Reasonably
Available Control Technology'', EPA (June 1992).
11. Beyond VOC RACT Requirements'', EPA (April 1995).
12. EPA's CTGs http://www.epa.gov/glo/SIPToolkit/ctgs.html.
13. CARB's emissions inventory database http://www.arb.ca.gov/app/emsinv/facinfo/facinfo.php
14. FRAQMD, CARB and EPA Region IX databases of FRAQMD rules--
FRAQMD: http://myairdistrict.com/index.php?Itemid=71
CARB: http://www.arb.ca.gov/ridb.htm
EPA: http://epa.gov/region09/air/sips/index.html
15. Implementation of the 2008 National Ambient Air Quality
Standards for Ozone: State Implementation Plan Requirements''--Final
Rule (80 FR 12264; March 6, 2015).
B. Does the RACT SIP submission meet the evaluation criteria?
The 2006, 2009 and 2014 RACT SIPs each includes three elements, as
described further below:
1. Evaluations of VOC and NOX rules for sources subject
to a CTG.
2. Negative declarations where there are no facilities subject to a
CTG.
3. Negative declaration for major non-CTG sources of VOC or
NOX.
A summary of our evaluation of each element is provided below. For
additional information concerning our evaluation, please refer to the
Technical Support Documents (TSDs) concerning the 2006, 2009 and 2014
RACT SIPs and FRAQMD Rule 3.8, which are available in the docket for
this action.
1. Evaluations of VOC and NOX Rules for Sources Subject to a
CTG
We believe that Rule 3.8 is consistent with the relevant
requirements, as well as policy and guidance regarding enforceability,
RACT, and SIP relaxations. We are not aware of information suggesting
that additional controls are needed to fulfill RACT.
2. Negative Declarations Where There are no Facilities Subject to a CTG
Negative declarations are only required for CTG source categories
for which the District has no sources covered by the CTG. A negative
declaration is not required for non-CTG source categories. Table 3
below lists the CTG source categories for the 2006, 2009 and 2014 RACT
SIPs. The District indicated it does not currently have, nor does it
anticipate sources subject to the CTGs in these categories in the
future. We searched CARB's emissions inventory database to verify there
are no facilities in FRAQMD that might be subject to the CTGs listed
below. We concur with the District's negative declarations.
Table 3--Negative Declarations for the 2006, 2009 and 2014 RACT SIPS
----------------------------------------------------------------------------------------------------------------
Negative declaration CTG 2006 RACT 2009 RACT 2014 RACT
CTG source category reference document SIP SIP SIP
----------------------------------------------------------------------------------------------------------------
Aerospace................................... EPA-453/R-97-004--Control of X .......... X
VOC Emissions from Coating
Operations at Aerospace
Manufacturing and Rework.
Automobile Coating; Metal Coil Container, & EPA-450/2-77-008--Control of X .......... X
Closure; Paper & Fabric. Volatile Organic Emissions
from Existing Stationary
Sources--Volume II Surface
Coating of Cans, Coils,
Paper, Fabrics, Automobiles,
and Light-Duty Trucks.
Automobile and Light-Duty Truck Assembly EPA-453/R-08-006--Control .......... X X
Coatings. Techniques Guidelines for
Automobile and Light-Duty
Assembly Coatings.
Cutback Asphalt............................. EPA-450/2-77-037--Control of X .......... X
Volatile Organic Emissions
from Use of Cutback Asphalt.
Dry Cleaning................................ EPA-450/3-82-009--Control of X .......... X
Volatile Organic Compound
Emissions from Large
Petroleum Dry Cleaners.
Flat Wood Paneling Coatings................. EPA-453/R-06-004--Control .......... X X
Techniques Guidelines for
Flat Wood Paneling Coatings.
Fiberglass Boat Manufacturing Materials..... EPA-453/R-08-004--Control .......... X X
Techniques Guidelines for
Fiberglass Boat Manufacturing
Materials.
Flexible Package Printing................... EPA-453/R06-003--Control .......... X X
Techniques Guidelines for
Flexible Package Printing.
[[Page 38962]]
Gasoline Loading Terminal................... EPA-450/2-77-026--Control of X .......... X
Hydrocarbons from Tank Truck
Gasoline Loading Terminals.
Gasoline Trucks............................. EPA-450/2-78-051--Control of X .......... X
Volatile Organic Compound
Leaks from Gasoline Tank
Trucks and Vapor Collection
Systems.
Gasoline Bulk Plants........................ EPA-450/2-77-035--Control of X .......... X
Volatile Organic Emissions
from Gasoline Bulk Plants.
Graphic Arts Rotogravure and Flexography.... EPA-450/2-78-033--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources--Volume VIII:
Rotogravure and Flexography.
Industrial Cleaning Solvents................ EPA-453/R-06-001--Control X X X
Techniques Guidelines for
Industrial Cleaning Solvents.
Large Appliance Coating..................... EPA-450/2-77-034--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources, Volume V: Surface
Coating of Large Appliances.
Large Appliance Coating..................... EPA-453/R-07-004--Control .......... X X
Techniques for Large
Appliance Coatings.
Magnet Wire Coating......................... EPA-450/2-77-033--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources--Volume IV: Surface
Coating of Insulation of
Magnet Wire.
Metal Can Coating; Metal Coil Coating....... EPA-450/2-77-008--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources--Volume II: Surface
Coating of Cans, Coils,
Paper, Fabrics, Automobiles,
and Light-Duty Trucks.
Metal Furniture............................. EPA-450/2-77-032--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources--Volume III: Surface
Coating of Metal Furniture.
Metal Furniture Coatings.................... EPA-453/R-07-005--Control .......... X X
Techniques Guidelines for
Metal Furniture Coatings.
Metal Parts and Products.................... EPA-450/2-78-015--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources--Volume VI: Surface
Coating of Miscellaneous
Parts and Products.
Miscellaneous Industrial Adhesives.......... EPA-453/R-08-005--Control X X X
Techniques Guidelines for
Miscellaneous Industrial
Adhesives.
Miscellaneous Metal and Plastic Parts EPA-453/R-08-003--Control .......... X X
Coatings. Techniques Guidelines for
Miscellaneous Metal and
Plastic Parts Coatings.
Natural Gas/Gasoline........................ EPA-450/2-83-007--Control of X .......... X
VOC Equipment Leaks from
Natural Gas/Gasoline
Processing Plants.
Offset Lithographic Printing and Letterpress EPA-453/R-06-002--Control .......... X X
Printing. Techniques Guidelines for
Offset Lithographic Printing
and Letterpress Printing.
Paper and Fabric Coating.................... EPA-450/2-77-008--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources--Volume II: Surface
Coating of Cans, Coils,
Paper, Fabrics, Automobiles,
and Light-Duty Trucks.
Paper, Film, and Foil Coatings.............. EPA-453/R-07-003--Control .......... X X
Techniques Guidelines for
Paper, Film, and Foil
Coatings.
Perchloroethylene Dry Cleaning Systems\1\... EPA-450/2-78-050--Control of .......... .......... X
Volatile Organic Emissions
from Perchloroethylene Dry
Cleaning Systems.
Petroleum Liquid Storage Tanks.............. EPA-450/2-77-036--Control of X .......... X
VOC Emissions from Storage of
Petroleum Liquids in Fixed
Roof Tanks.
Petroleum Liquid Storage Tanks.............. EPA-450/2-78-047--Control of X .......... X
VOC Emissions from Petroleum
Liquid Storage in External
Floating Roof Tanks.
Pharmaceutical Products..................... EPA-450/2-78-029--Control of X .......... X
Volatile Organic Emissions
from Manufacture of
Synthesized Pharmaceutical
Products.
Resin Manufacturing......................... EPA-450/3-83-008--Control of X .......... X
VOC Emissions from
Manufacture of High-Density
Polyethylene, Polypropylene,
and Polystyrene Resins.
Resin Manufacturing......................... EPA-450/3-83-006--Control of X .......... X
VOC Fugitive Emissions from
Synthetic Organic Chemical
Polymer and Resin
Manufacturing Equipment.
Refineries.................................. EPA-450/2-77-025--Control of X .......... X
Refinery Vacuum Producing
Systems, Wastewater
Separators, and Process Unit
Turnarounds.
Refineries.................................. EPA-450/2-78-036--Control of X .......... X
VOC Leaks from Petroleum
Refinery Equipment.
Rubber Tire Manufacturing................... EPA-450/2-78-030--Control of X .......... X
Volatile Organic Emissions
from Manufacture of Pneumatic
Rubber Tires.
Ship Coatings............................... 61 FR 44050 Shipbuilding and X .......... X
Ship Repair Operations
(Surface Coating).
Ship Coatings............................... EPA-453/R-94-032--Alternative .......... .......... X
Control Technology Document--
Surface Coating Operations at
Shipbuilding and Ship Repair
Operations (Surface Coating).
Solvent Cleaning Degreasers................. EPA-450/2-77-022--Control of X .......... X
Volatile Organic Emissions
from Solvent Metal Cleaning.
[[Page 38963]]
Synthetic Organic Chemical Manufacturing.... EPA-450/3-84-015--Control of X .......... X
VOC Emissions from Air
Oxidation Processes in
Synthetic Organic Chemical
Manufacturing Industry.
Synthetic Organic Chemical Manufacturing.... EPA-450/4-91-031--Control of X .......... X
VOC Emissions from Reactor
Processes and Distillation
Operations in Synthetic
Organic Chemical
Manufacturing Industry.
Wood Coating Factory Surface of Flat Wood EPA-450/2-78-032--Control of X .......... X
Paneling. Volatile Organic Emissions
from Existing Stationary
Sources--Volume VII: Factory
Surface of Flat Wood Paneling.
Wood Furniture Coating...................... EPA-453/R-96-007--Control of X .......... X
VOC Emissions from Wood
Furniture Manufacturing
Operations.
----------------------------------------------------------------------------------------------------------------
\1\ This item is not a CTG because EPA exempted perchloroethylene as a VOC for purposes of ozone SIPs. 61 FR
4588 (February 7, 1996) (codified at 40 CFR 51.100(s)(1)).
3. Negative Declaration for Major Non-CTG Sources of VOC or
NOX
The 2006, 2009 and 2014 RACT SIPs each included a negative
declaration for major non-CTG sources of VOC and NOX. EPA
agrees that there are no major non-CTG sources of NOX or
VOCs in the south Sutter County nonattainment area.
4. Conclusion
We find that FRAQMD's 2006, 2009, and 2014 RACT SIPs including the
negative declarations and the Rule 3.8 revisions, adequately
demonstrate that they satisfy RACT for the 1997 and 2008 8-hour ozone
NAAQS. Our TSDs have more information on our evaluation of the three
RACT SIP submissions and Rule 3.8.
C. EPA Recommendations To Strengthen the RACT SIPs and the Rule
Our TSD for Rule 3.8 describes additional revisions that we
recommend for the next time FRAQMD modifies the rule.
D. Public Comment and Final Action
As authorized in section 110(k)(3) of the Act, EPA is fully
approving the submitted SIP revisions because we believe they fulfill
all relevant requirements. We do not think anyone will object to this
approval, so we are finalizing it without proposing it in advance.
However, in the Proposed Rules section of this Federal Register, we are
simultaneously proposing approval of the same SIP revisions. If we
receive adverse comments by August 7, 2015, we will publish a timely
withdrawal in the Federal Register to notify the public that the direct
final approval will not take effect and we will address the comments in
a subsequent final action based on the proposal. If we do not receive
timely adverse comments, the direct final approval will be effective
without further notice on September 8, 2015. This will incorporate
these documents and rule into the federally enforceable SIP.
Please note that if EPA receives adverse comment on a specific
provision of this SIP revision and if that provision may be severed
from the remainder of the SIP revision, EPA may adopt as final those
provisions of the SIP revision that are not the subject of an adverse
comment.
III. Incorporation by Reference
In this rule, the EPA is finalizing regulatory text that includes
incorporation by reference. In accordance with requirements of 1 CFR
51.5, EPA is finalizing the incorporation by reference of the FRAQMD
rule described in the amendments to 40 CFR 52 set forth below. EPA has
made, and will continue to make, this document available electronically
through www.regulations.gov and in hard copy at the appropriate EPA
office (see the ADDRESSES section of this preamble for more
information).
IV. Statutory and Executive Order Reviews
Under the Clean Air Act, the Administrator is required to approve a
SIP submission that complies with the provisions of the Act and
applicable Federal regulations. 42 U.S.C. 7410(k); 40 CFR 52.02(a).
Thus, in reviewing SIP submissions, EPA's role is to approve state
choices, provided that they meet the criteria of the Clean Air Act.
Accordingly, this action merely approves state law as meeting Federal
requirements and does not impose additional requirements beyond those
imposed by state law. For that reason, this action:
Is not a ``significant regulatory action'' subject to
review by the Office of Management and Budget under Executive Order
12866 (58 FR 51735, October 4, 1993);
does not impose an information collection burden under the
provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq.);
is certified as not having a significant
economic impact on a substantial number of small entities under the
Regulatory Flexibility Act (5 U.S.C. 601 et seq.);
does not contain any unfunded mandate or significantly or
uniquely affect small governments, as described in the Unfunded
Mandates Reform Act of 1995 (Pub. L. 104-4);
does not have Federalism implications as specified in
Executive Order 13132 (64 FR 43255, August 10, 1999);
is not an economically significant regulatory action based
on health or safety risks subject to Executive Order 13045 (62 FR
19885, April 23, 1997);
is not a significant regulatory action subject to
Executive Order 13211 (66 FR 28355, May 22, 2001);
is not subject to requirements of Section 12(d) of the
National Technology Transfer and Advancement Act of 1995 (15 U.S.C. 272
note) because application of those requirements would be inconsistent
with the Clean Air Act; and
does not provide EPA with the discretionary authority to
address disproportionate human health or environmental effects with
practical, appropriate, and legally permissible methods under Executive
Order 12898 (59 FR 7629, February 16, 1994).
In addition, the SIPs and the rule are not approved to apply on any
Indian reservation land or in any other area where EPA or an Indian
tribe has demonstrated that a tribe has jurisdiction. In those areas of
Indian country, the rule does not have tribal implications and will not
impose substantial direct costs on tribal governments or preempt tribal
law as
[[Page 38964]]
specified by Executive Order 13175 (65 FR 67249, November 9, 2000).
The Congressional Review Act, 5 U.S.C. 801 et seq., as added by the
Small Business Regulatory Enforcement Fairness Act of 1996, generally
provides that before a rule may take effect, the agency promulgating
the rule must submit a rule report, which includes a copy of the rule,
to each House of the Congress and to the Comptroller General of the
United States. EPA will submit a report containing this action and
other required information to the U.S. Senate, the U.S. House of
Representatives, and the Comptroller General of the United States prior
to publication of the rule in the Federal Register. A major rule cannot
take effect until 60 days after it is published in the Federal
Register. This action is not a ``major rule'' as defined by 5 U.S.C.
804(2).
Under section 307(b)(1) of the Clean Air Act, petitions for
judicial review of this action must be filed in the United States Court
of Appeals for the appropriate circuit by September 8, 2015. Filing a
petition for reconsideration by the Administrator of this final rule
does not affect the finality of this action for the purposes of
judicial review nor does it extend the time within which a petition for
judicial review may be filed, and shall not postpone the effectiveness
of such rule or action. Parties with objections to this direct final
rule are encouraged to file a comment in response to the parallel
notice of proposed rulemaking for this action published in the Proposed
Rules section of today's Federal Register, rather than file an
immediate petition for judicial review of this direct final rule, so
that EPA can withdraw this direct final rule and address the comment in
the proposed rulemaking. This action may not be challenged later in
proceedings to enforce its requirements (see section 307(b)(2)).
List of Subjects in 40 CFR Part 52
Environmental protection, Air pollution control, Incorporation by
reference, Intergovernmental relations, Nitrogen dioxide, Ozone,
Reporting and recordkeeping requirements, Volatile organic compounds.
Authority: 42 U.S.C. 7401 et seq.
Dated: April 30, 2015.
Jared Blumenfeld,
Regional Administrator, Region IX.
Part 52, Chapter I, Title 40 of the Code of Federal Regulations is
amended as follows:
PART 52--[AMENDED]
0
1. The authority citation for part 52 continues to read as follows:
Authority: 42 U.S.C. 7401 et seq.
Subpart F--California
0
2. Section 52.220 is amended by adding paragraphs (c)(382)(ii)(B),
(c)(457)(i)(A)(3), (c)(459) and (c)(460) to read as follows:
Sec. 52.220 Identification of plan.
* * * * *
(c) * * *
(382) * * *
(ii) * * *
(B) Feather River Air Quality Management District.
(1) 2006 Reasonably Available Control Technology (RACT) Analysis
for State Implementation Plan (SIP) (``2006 RACT SIP'') as adopted on
December 4, 2006.
* * * * *
(457) * * *
(i) * * *
(A) * * *
(3) Rule 3.8, ``Gasoline Dispensing Facilities,'' amended on June
2, 2014.
* * * * *
(459) The following plan revision was submitted on September 29,
2014, by the Governor's designee.
(i) [Reserved]
(ii) Additional Material.
(A) Feather River Air Quality Management District.
(1) Reasonably Available Control Technology Analysis and Negative
Declarations (``2014 RACT SIP''), as adopted on August 4, 2014.
(460) New and amended regulations for the following AQMDs were
submitted on November 5, 2014 by the Governor's designee.
(i) Incorporation by Reference.
(A) Feather River Air Quality Management District.
(1) Rule 3.8, ``Gasoline Dispensing Facilities,'' amended on June
2, 2014.
0
3. Section 52.222 is amended by adding paragraph (a)(11) to read as
follows:
Sec. 52.222 Negative declarations.
(a) * * *
(11) Feather River Air Quality Management District.
----------------------------------------------------------------------------------------------------------------
2006 RACT 2009 RACT 2014 RACT
Negative declaration CTG SIP SIP SIP
CTG source category reference document submitted submitted submitted
7/11/07 10/27/09 9/29/14
----------------------------------------------------------------------------------------------------------------
Aerospace................................... EPA-453/R-97-004--Control of X .......... X
VOC Emissions from Coating
Operations at Aerospace
Manufacturing and Rework.
Automobile Coating; Metal Coil Container, & EPA-450/2-77-008--Control of X .......... X
Closure; Paper & Fabric. Volatile Organic Emissions
from Existing Stationary
Sources--Volume II Surface
Coating of Cans, Coils,
Paper, Fabrics, Automobiles,
and Light-Duty Trucks.
Automobile and Light-Duty Truck Assembly EPA-453/R-08-006--Control .......... X X
Coatings. Techniques Guidelines for
Automobile and Light-Duty
Assembly Coatings.
Cutback Asphalt............................. EPA-450/2-77-037--Control of X .......... X
Volatile Organic Emissions
from Use of Cutback Asphalt.
Dry Cleaning................................ EPA-450/3-82-009--Control of X .......... X
Volatile Organic Compound
Emissions from Large
Petroleum Dry Cleaners.
Flat Wood Paneling Coatings................. EPA-453/R-06-004--Control .......... X X
Techniques Guidelines for
Flat Wood Paneling Coatings.
Fiberglass Boat Manufacturing Materials..... EPA-453/R-08-004--Control .......... X X
Techniques Guidelines for
Fiberglass Boat Manufacturing
Materials.
Flexible Package Printing................... EPA-453/R06-003--Control .......... X X
Techniques Guidelines for
Flexible Package Printing.
Gasoline Loading Terminal................... EPA-450/2-77-026--Control of X .......... X
Hydrocarbons from Tank Truck
Gasoline Loading Terminals.
Gasoline Trucks............................. EPA-450/2-78-051--Control of X .......... X
Volatile Organic Compound
Leaks from Gasoline Tank
Trucks and Vapor Collection
Systems.
Gasoline Bulk Plants........................ EPA-450/2-77-035--Control of X .......... X
Volatile Organic Emissions
from Gasoline Bulk Plants.
[[Page 38965]]
Graphic Arts Rotogravure and Flexography.... EPA-450/2-78-033--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources--Volume VIII:
Rotogravure and Flexography.
Industrial Cleaning Solvents................ EPA-453/R-06-001--Control X X X
Techniques Guidelines for
Industrial Cleaning Solvents.
Large Appliance Coating..................... EPA-450/2-77-034--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources, Volume V: Surface
Coating of Large Appliances.
Large Appliance Coating..................... EPA-453/R-07-004--Control .......... X X
Techniques for Large
Appliance Coatings.
Magnet Wire Coating......................... EPA-450/2-77-033--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources--Volume IV: Surface
Coating of Insulation of
Magnet Wire.
Metal Can Coating; Metal Coil Coating....... EPA-450/2-77-008--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources--Volume II: Surface
Coating of Cans, Coils,
Paper, Fabrics, Automobiles,
and Light-Duty Trucks.
Metal Furniture............................. EPA-450/2-77-032--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources--Volume III: Surface
Coating of Metal Furniture.
Metal Furniture Coatings.................... EPA-453/R-07-005--Control .......... X X
Techniques Guidelines for
Metal Furniture Coatings.
Metal Parts and Products.................... EPA-450/2-78-015--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources--Volume VI: Surface
Coating of Miscellaneous
Parts and Products.
Miscellaneous Industrial Adhesives.......... EPA-453/R-08-005--Control X X X
Techniques Guidelines for
Miscellaneous Industrial
Adhesives.
Miscellaneous Metal and Plastic Parts EPA-453/R-08-003--Control .......... X X
Coatings. Techniques Guidelines for
Miscellaneous Metal and
Plastic Parts Coatings.
Natural Gas/Gasoline........................ EPA-450/2-83-007--Control of X .......... X
VOC Equipment Leaks from
Natural Gas/Gasoline
Processing Plants.
Offset Lithographic Printing and Letterpress EPA-453/R-06-002--Control .......... X X
Printing. Techniques Guidelines for
Offset Lithographic Printing
and Letterpress Printing.
Paper and Fabric Coating.................... EPA-450/2-77-008--Control of X .......... X
Volatile Organic Emissions
from Existing Stationary
Sources--Volume II: Surface
Coating of Cans, Coils,
Paper, Fabrics, Automobiles,
and Light-Duty Trucks.
Paper, Film, and Foil Coatings.............. EPA-453/R-07-003--Control .......... X X
Techniques Guidelines for
Paper, Film, and Foil
Coatings.
Petroleum Liquid Storage Tanks.............. EPA-450/2-77-036--Control of X .......... X
VOC Emissions from Storage of
Petroleum Liquids in Fixed
Roof Tanks.
Petroleum Liquid Storage Tanks.............. EPA-450/2-78-047--Control of X .......... X
VOC Emissions from Petroleum
Liquid Storage in External
Floating Roof Tanks.
Pharmaceutical Products..................... EPA-450/2-78-029--Control of X .......... X
Volatile Organic Emissions
from Manufacture of
Synthesized Pharmaceutical
Products.
Resin Manufacturing......................... EPA-450/3-83-008--Control of X .......... X
VOC Emissions from
Manufacture of High-Density
Polyethylene, Polypropylene,
and Polystyrene Resins.
Resin Manufacturing......................... EPA-450/3-83-006--Control of X .......... X
VOC Fugitive Emissions from
Synthetic Organic Chemical
Polymer and Resin
Manufacturing Equipment.
Refineries.................................. EPA-450/2-77-025--Control of X .......... X
Refinery Vacuum Producing
Systems, Wastewater
Separators, and Process Unit
Turnarounds.
Refineries.................................. EPA-450/2-78-036--Control of X .......... X
VOC Leaks from Petroleum
Refinery Equipment.
Rubber Tire Manufacturing................... EPA-450/2-78-030--Control of X .......... X
Volatile Organic Emissions
from Manufacture of Pneumatic
Rubber Tires.
Ship Coatings............................... 61 FR 44050 Shipbuilding and X .......... X
Ship Repair Operations
(Surface Coating).
Ship Coatings............................... EPA-453/R-94-032--Alternative .......... .......... X
Control Technology Document--
Surface Coating Operations at
Shipbuilding and Ship Repair
Operations (Surface Coating).
Solvent Cleaning Degreasers................. EPA-450/2-77-022--Control of X .......... X
Volatile Organic Emissions
from Solvent Metal Cleaning.
Synthetic Organic Chemical Manufacturing.... EPA-450/3-84-015--Control of X .......... X
VOC Emissions from Air
Oxidation Processes in
Synthetic Organic Chemical
Manufacturing Industry.
Synthetic Organic Chemical Manufacturing.... EPA-450/4-91-031--Control of X .......... X
VOC Emissions from Reactor
Processes and Distillation
Operations in Synthetic
Organic Chemical
Manufacturing Industry.
Wood Coating Factory Surface of Flat Wood EPA-450/2-78-032--Control of X .......... X
Paneling. Volatile Organic Emissions
from Existing Stationary
Sources--Volume VII: Factory
Surface of Flat Wood Paneling.
[[Page 38966]]
Wood Furniture Coating...................... EPA-453/R-96-007--Control of X .......... X
VOC Emissions from Wood
Furniture Manufacturing
Operations.
----------------------------------------------------------------------------------------------------------------
[FR Doc. 2015-16627 Filed 7-7-15; 8:45 am]
BILLING CODE 6560-50-P